Home › Suspension › TIRE PRESSURE MONITORING › TIRE PRESSURE WARNING SYSTEM › from 2019.06
RM35X0E _53 Suspension _078885 TIRE PRESSURE MONITORING _0382739 TIRE PRESSURE WARNING SYSTEM C

TIRE PRESSURE MONITORING  TIRE PRESSURE WARNING SYSTEM  C2198  Initialization Switch (for Test Mode DTC)  


DESCRIPTION

During test mode, when the tire pressure warning reset switch is on, the tire pressure warning light comes on and when the tire pressure warning reset switch is off, the tire pressure warning light blinks at 0.125 second intervals.

DTC No. Detection Item DTC Detection Condition Trouble Area Note
C2198 Initialization Switch (for Test Mode DTC) Test mode procedure is performed.
·

Tire pressure warning reset switch

·

Harness or connector

·

Tire pressure warning ECU and receiver


-

WIRING DIAGRAM

C420988E02
1.844,1.188 2.302,1.385 0.458,0.198 10 false N63 1.844,1.417 4.438,1.677 2.594,0.26 10 false Tire Pressure Warning Reset Switch 2.115,0.74 2.271,0.938 0.156,0.198 10 false 2 3.313,0.729 3.469,0.927 0.156,0.198 10 false 1 5.354,0.854 5.969,1.052 0.615,0.198 10 false CLSW 5.104,0.74 5.26,0.938 0.156,0.198 10 false 3 4.604,1.646 6.292,1.844 1.688,0.198 10 false Z3*1, Z30*2 4.594,1.875 7.135,2.177 2.542,0.302 10 false Tire Pressure Warning ECU and Receiver 0.323,2.958 6.708,3.781 6.385,0.823 10 false *1: w/o Entry and Start System and w/o Wireless Door Lock Control System, for GDH303L-RDTJY and GDH303L-RDTGY w/ Entry and Start System (for FMVSS138 Type 0.302,4.125 6.677,5.021 6.375,0.896 10 false *2: w/o Entry and Start System and w/ Wireless Door Lock Control System or for GDH303L-RDTJY and GDH303L-RDTGY w/ Entry and Start System (for ECE-R64 Type)

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the tire pressure warning ECU and receiver, read the transmitter IDs and number of the transmitters (4 or 5) stored in the old ECU using the GTS and write them down before removal.

·

It is necessary to perform initialization Suspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>INITIALIZATION after registration Suspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>REGISTRATION of the transmitter IDs into the tire pressure warning ECU and receiver if the ECU has been replaced.



PROCEDURE

1.INSPECT TIRE PRESSURE WARNING RESET SWITCH
a.

Turn the ignition switch off.


b.

Remove the tire pressure warning reset switch.

Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING RESET SWITCH>REMOVAL


c.

Inspect the tire pressure warning reset switch.

Click hereSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING RESET SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (TIRE PRESSURE WARNING RESET SWITCH - TIRE PRESSURE WARNING ECU AND RECEIVER)

NG

REPLACE TIRE PRESSURE WARNING RESET SWITCH

2.CHECK HARNESS AND CONNECTOR (TIRE PRESSURE WARNING RESET SWITCH - TIRE PRESSURE WARNING ECU AND RECEIVER)
a.

Disconnect the N63 tire pressure warning reset switch connector.


b.

Disconnect the Z3*1 or Z30*2 tire pressure warning ECU and receiver connector.

*1: w/o Entry and Start System and w/o Wireless Door Lock Control System, for GDH303L-RDTJY and GDH303L-RDTGY w/ Entry and Start System (for FMVSS138 Type)

*2: w/o Entry and Start System and w/ Wireless Door Lock Control System or for GDH303L-RDTJY and GDH303L-RDTGY w/ Entry and Start System (for ECE-R64 Type)



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
w/o Entry and Start System and w/o Wireless Door Lock Control System, for GDH303L-RDTJY and GDH303L-RDTGY w/ Entry and Start System (for FMVSS138 Type):
Tester Connection Condition Specified Condition
Z3-3 (CLSW) - N63-1 Always Below 1 Ω
Z3-3 (CLSW) or N63-1 - Body ground Always 10 kΩ or higher
N63-2 - Body ground Always Below 1 Ω

w/o Entry and Start System and w/ Wireless Door Lock Control System or for GDH303L-RDTJY and GDH303L-RDTGY w/ Entry and Start System (for ECE-R64 Type):
Tester Connection Condition Specified Condition
Z30-3 (CLSW) - N63-1 Always Below 1 Ω
Z30-3 (CLSW) or N63-1 - Body ground Always 10 kΩ or higher
N63-2 - Body ground Always Below 1 Ω


Result:
Proceed to
OK
NG




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR