Home › General › MAINTENANCE › 1GD-FTV BATTERY › from 2019.06
RM35X0E _V1 General _078672 MAINTENANCE _0387106 1GD-FTV BATTERY A

MAINTENANCE  1GD-FTV BATTERY  REMOVAL  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedures for the RH side and LH side.

·

The procedures listed below are for the LH side.



CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the battery removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Battery terminal is disconnected/reconnected Memorize steering angle neutral point Parking assist monitor system (Click here)
Panoramic view monitor system (Click here)

HINT:

When the cable is disconnected / reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative when not Performed Necessary Procedures Link
Stop and start system Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes). (Click here)
Lane control system Drive the vehicle straight ahead at 15 km/h (10 mph) or more for 1 second or more. (Click here)
Pre-collision system

·

Learning completes when vehicle is operated normally

Effect/Inoperative when not Performed Necessary Procedures Link
Power slide door system Fully close the slide door by hand.
HINT:

Initialization is not necessary if the above procedures are performed while the slide door is closed.


(Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 1. PRECAUTION

NOTICE:
·

After turning the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

w/o Stop And Start System:

When replacing the battery, use a new battery of the same dimensions with a capacity of 70 Ah or more at a 20-hour rate.

·

w/ Stop And Start System:

When replacing the battery, use a new battery of the same dimensions with a capacity of 75 Ah or more at a 20-hour rate.



Hide 2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
B394718

·

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

·

If the airbag deploys for any reason, it may cause a serious accident.



a.

w/o Stop And Start System:

i.
A456439C02
0,0 0,0 false
V113147

Remove in this Direction


Turn the 2 knobs right to release the lock and remove the door scuff plate cover.


ii.
A437139C02
0,0 0,0 false
V113147

Remove in this Direction


Place your hands as shown and pull toward the outer side to remove the front battery service hole cover sub-assembly LH.


iii.
A437140

Loosen the nut, and disconnect the cable from the negative (-) battery terminal.



b.

w/ Stop And Start System:

i.
A456440

Insert a screwdriver into the gap, detach the claw and remove the 2 front door outside scuff plate LH.


ii.
A456441

Remove the 6 bolts.


iii.

Detach the 2 claws and remove the front door scuff plate LH.


iv.
A437077

Remove the 5 bolts.


v.
A437078C01
0,0 0,0 false
V113147

Remove in this Direction


Hold the top part of the battery service hole cover sub-assembly LH and tilt it toward the outer side.


vi.
A437079C01
0,0 0,0 false
V113147

Remove in this Direction


Lift it further up and remove the battery service hole cover sub-assembly LH.


vii.
A437518

Loosen the nut, and disconnect the cable from the negative (-) battery terminal.



Hide 28800 3.REMOVE BATTERY

a.

w/o Stop And Start System:

i.
A437075

Insert a screwdriver into the gap, detach the claw and remove the 2 front door outside scuff plate LH.


ii.
A437141

Remove the 6 bolts.


iii.

Detach the 2 claws and remove the front door scuff plate LH.


iv.
A437077

Remove the 5 bolts.


v.
A437078C01
0,0 0,0 false
V113147

Remove in this Direction


Hold the top part of the battery service hole cover sub-assembly LH and tilt it toward the outer side.


vi.
A437079C01
0,0 0,0 false
V113147

Remove in this Direction


Lift it further up and remove the battery service hole cover sub-assembly LH.



b.
A437109

Open the connector cover.


c.
A437110

Loosen the nut and disconnect the cable from the positive (+) battery terminal.


d.
A437080

Remove the 2 bolts and battery clamp.


e.
A437081C01
0,0 0,0 false
V113147

Remove in this Direction


Slide the battery to the outer side.


f.
A437082C01
0,0 0,0 false
V113147

Remove in this Direction


Lift the battery and remove it from the vehicle.