Home › Engine / Hybrid System › 1GD-FTV (INTAKE / EXHAUST) › INTERCOOLER › 2019.06–2021.07
RM35X0E _51 Engine / Hybrid System _079307 1GD-FTV INTAKE / EXHAUST _0385722 INTERCOOLER A

1GD-FTV INTAKE / EXHAUST  INTERCOOLER  INSTALLATION  


PROCEDURE

Hide 1.INSTALL GROMMET

a.

Install the 2 grommets to the lower radiator support assembly.


Hide 17940D 2.INSTALL INTERCOOLER ASSEMBLY

a.
A438469

Attach the 2 guides and install the intercooler assembly to the lower radiator support assembly.


Hide 88689E 3.INSTALL NO. 1 COOLER BRACKET

a.
A438467

Install the No. 1 cooler bracket to the radiator support assembly with the 4 nuts.

Torque:
24 N*m (245 kgf*cm, 18 ft.*lbf)


b.

Install the intercooler assembly to the No. 1 cooler bracket with the 2 bolts.

Torque:
6.0 N*m (61 kgf*cm, 53 in.*lbf)


Hide 17942 4.INSTALL NO. 2 INTERCOOLER AIR GUIDE

a.
A438466

Attach the claws to install the No. 2 intercooler air guide.


Hide 17941 5.INSTALL NO. 1 INTERCOOLER AIR GUIDE

a.
A438178

Attach the claws to install the No. 1 intercooler air guide.


Hide 17312B 6.INSTALL NO. 2 AIR INLET DUCT

a.
A438177

for RH Side:

Attach the claws to install the No. 2 air inlet duct.


b.
A438465

for LH Side:

Attach the claws to install the No. 2 air inlet duct.


Hide 44402 7.CONNECT NO. 1 POWER STEERING OIL COOLER SUB-ASSEMBLY

a.
A438175

for LHD:

Connect the No. 1 power steering oil cooler sub-assembly with the 3 bolts.

Torque:
28 N*m (286 kgf*cm, 21 ft.*lbf)


b.
A438176

for RHD:

Connect the No. 1 power steering oil cooler sub-assembly with the 4 bolts.

Torque:
28 N*m (286 kgf*cm, 21 ft.*lbf)


Hide 53287B 8.INSTALL RADIATOR SUPPORT EXTENSION RH

a.
A438173C01
0.073,0.042 0.385,0.198 0.313,0.156 10 true *A 0.094,2.375 0.406,2.531 0.313,0.156 10 false *B
*A for LHD
*B for RHD


Attach the claws to install the radiator support extension RH.


Hide 53288B 9.INSTALL RADIATOR SUPPORT EXTENSION LH

a.
A438171C01
0.073,0.042 0.385,0.198 0.313,0.156 10 true *A 0.094,2.375 0.406,2.531 0.313,0.156 10 false *B
*A for LHD
*B for RHD


Attach the claws to install the radiator support extension LH.


Hide 17303T 10.INSTALL AIR PIPE SUB-ASSEMBLY

NOTICE:
·

When tightening the hose clamp, carefully tighten it so that it does not become damaged.

·

The tightening method for the hose clamp differs depending on the shape of the air pipe sub-assembly.

A456626C01
1.865,0.833 1.552,0.188 1.552,0.188 1.344,0.188 true 0.031,0.031 0.344,0.188 0.313,0.156 10 false *A 3.667,0.063 3.979,0.219 0.313,0.156 10 false *B 1.146,0.104 1.458,0.26 0.313,0.156 10 false *a
*A for Type A *B for Type B
*a Cutout - -




a.

for Intake Air Connector Side (for Type A):

i.

Install 2 new hose clamps to the air pipe sub-assembly.


ii.
A449499C01
1.01,3.167 1.927,3.167 true 0.99,2.802 1.906,2.802 true 0.99,2.438 1.906,2.438 true 2.583,0.927 3.042,0.927 true 0.823,2.354 1.135,2.51 0.313,0.156 10 false *1 0.833,3.073 1.146,3.229 0.313,0.156 10 false *2 0.469,1.76 0.781,1.917 0.313,0.156 10 false *a 3.083,0.833 3.333,0.99 0.25,0.156 10 false *b 0.823,2.719 1.135,2.875 0.313,0.156 10 false *1
*1 Hose Clamp
*2 Air Pipe Sub-assembly
*a 50 mm (1.97 in.) or Less
*b Hair Dryer


When the ambient temperature drops below 15°C: [*1]

Using a hair dryer, warm the inside of the air pipe sub-assembly as shown in the illustration.

Recommended Hair Dryer Rated Power:

1200 W


HINT:
·

Warm the part until the temperature is 30°C or more.

·

Warm the part for 90 seconds or more.

·

After warming, connect the air pipe sub-assembly within 5 minutes and tighten the hose clamp.




iii.
A449500C01
2.906,2.813 2.771,2.688 false 2.948,2.771 3.26,2.927 0.313,0.156 10 false *a 2.667,3.083 2.979,3.24 0.313,0.156 10 false *b
*a Stopper
*b 0 to 3 mm (0 to 0.118 in.)


Connect the air pipe sub-assembly to the intake air connector.

HINT:

Make sure the hose clamp is oriented as shown in the illustration.



iv.
A449501C01
1.094,0.854 1.594,1.115 true 0.896,0.729 1.104,0.906 0.208,0.177 10 true *1
*1 Hose Clamp (A)


Tighten the hose clamp (A).

NOTICE:

Do not use electric or pneumatic tools.



v.
A449503C01
0.99,2.927 1.344,2.927 true 1.552,1.865 1.906,1.865 true 1.031,0.792 1.385,0.792 true 0.875,0.698 1.188,0.854 0.313,0.156 10 false *a 1.167,0.146 1.365,0.313 0.198,0.167 10 true *b 1.792,0.208 2.104,0.365 0.313,0.156 10 false *c 1.802,1.323 2.115,1.479 0.313,0.156 10 false *d 1.823,2.396 2.135,2.552 0.313,0.156 10 false *e 1.917,1.781 2.135,1.938 0.219,0.156 10 true *a 0.823,2.844 1.135,3 0.313,0.156 10 false *a
*a Paint Mark
*b 2.0 mm (0.0787 in.)
*c CORRECT
*d INCORRECT (1)
*e INCORRECT (2)


Make sure that the paint mark of the hose clamp (A) is positioned as shown in the illustration.

NOTICE:
When "INCORRECT (1)":
·

Disconnect the air pipe sub-assembly and replace the hose clamp (A) with new ones.

·

Perform the procedure again from [*1].



NOTICE:
When "INCORRECT (2)":
·

With the air pipe sub-assembly connected, warm the air pipe sub-assembly from the outside. (When the ambient temperature drops below 15°C.)

HINT:
·

Warm the part until the temperature is 30°C or more.

·

Warm the part for 90 seconds or more.



·

Tighten the hose clamp (A) and check the position of the paint mark of the hose clamp (A) again.




vi.
A449502C01
0.833,1.104 1.333,1.365 true 0.635,0.99 0.844,1.156 0.208,0.167 10 true *1
*1 Hose Clamp (B)


Tighten the hose clamp (B).

NOTICE:

Do not use electric or pneumatic tools.



vii.
A449503C01
0.99,2.927 1.344,2.927 true 1.552,1.865 1.906,1.865 true 1.031,0.792 1.385,0.792 true 0.875,0.698 1.188,0.854 0.313,0.156 10 false *a 1.167,0.146 1.365,0.313 0.198,0.167 10 true *b 1.792,0.208 2.104,0.365 0.313,0.156 10 false *c 1.802,1.323 2.115,1.479 0.313,0.156 10 false *d 1.823,2.396 2.135,2.552 0.313,0.156 10 false *e 1.917,1.781 2.135,1.938 0.219,0.156 10 true *a 0.823,2.844 1.135,3 0.313,0.156 10 false *a
*a Paint Mark
*b 2.0 mm (0.0787 in.)
*c CORRECT
*d INCORRECT (1)
*e INCORRECT (2)


Make sure that the paint mark of the hose clamp (B) is positioned as shown in the illustration.

NOTICE:
When "INCORRECT (1)":
·

Disconnect the air pipe sub-assembly and replace the hose clamps (A and B) with new ones.

·

Perform the procedure again from [*1].



NOTICE:
When "INCORRECT (2)":
·

With the air pipe sub-assembly connected, warm the air pipe sub-assembly from the outside. (When the ambient temperature drops below 15°C.)

HINT:
·

Warm the part until the temperature is 30°C or more.

·

Warm the part for 90 seconds or more.



·

Tighten the hose clamp (B) and check the position of the paint mark of the hose clamp (B) again.





b.

for Intake Air Connector Side (for Type B):

i.

Install 2 new hose clamps to the air pipe sub-assembly.


ii.
A456627C01
2.885,2.885 2.979,3.031 2.979,3.031 3.073,3.031 false 1.625,3.073 1.49,3.073 1.49,3.073 1.25,2.583 true 0.844,3.125 0.99,3.125 0.99,3.125 1.125,2.583 true 3.104,2.948 3.333,3.167 0.229,0.219 10 false *c 2.771,3.208 3.083,3.365 0.313,0.156 10 false *d 0.625,3.052 0.854,3.271 0.229,0.219 10 false *a 1.646,3.021 1.958,3.177 0.313,0.156 10 false *b 1.875,0.042 2.01,0.198 0.135,0.156 10 true 1 1.344,0.104 1.458,0.25 0.115,0.146 10 true 2
*a Paint Mark
*b Rib
*c Stopper
*d 0 to 3 mm (0 to 0.118 in.)


Connect the air pipe sub-assembly to the intake air connector with 2 new hose clamps as shown in the illustration.

Torque:
9.5 N*m (97 kgf*cm, 84 in.*lbf)

NOTICE:
·

Do not reuse the hose clamp.

·

Tighten the hose clamps in the order shown in the illustration.



HINT:

Make sure the hose clamp is oriented as shown in the illustration.




c.

for Intercooler Assembly Side:

i.
A439809C01
1.031,2.667 0.969,2.5 0.969,2.5 0.771,2.5 true 2.521,2.625 2.458,2.458 2.458,2.458 2.26,2.458 true 1.115,3.073 1.115,2.896 true 2.771,3.073 2.771,2.896 true 0.813,1.906 1.125,2.063 0.313,0.156 10 false *a 2.365,1.906 2.677,2.063 0.313,0.156 10 false *b 0.583,2.385 0.781,2.583 0.198,0.198 10 true *c 2.063,2.354 2.26,2.552 0.198,0.198 10 true *c 1.031,3.083 1.229,3.281 0.198,0.198 10 true *d 2.677,3.094 2.875,3.292 0.198,0.198 10 true *d
*a Correct
*b Incorrect
*c Retainer End
*d Stopper


Connect the No. 2 air tube to the intercooler assembly and lock the retainer.

NOTICE:

Securely insert the retainer so that the 4 locks are engaged. Then, pull and check that the locks are engaged and that the hose cannot be pulled out.


HINT:

Make sure that the retainer end contacts the stopper as shown in the illustration.




Hide 25761B 11.CONNECT NO. 1 VACUUM TRANSMITTING HOSE

a.
A443469

for Diesel Throttle Body Side:

Attach the 5 clamps and connect the No. 1 vacuum transmitting hose to the intercooler assembly, and slide the clip to secure the hose to the engine oil dipstick guide.


b.
A438168

for Intercooler Assembly Side:

Connect the No. 1 vacuum transmitting hose to the intercooler assembly, and slide the clip to secure the hose.


Hide 17030 12.INSTALL AIR HOSE ASSEMBLY

a.
A438170C01
0.823,2.073 1.135,2.229 0.313,0.156 10 false *a 2.396,2.01 2.708,2.167 0.313,0.156 10 false *b 2.469,2.188 2.781,2.344 0.313,0.156 10 false *c 2.708,2.344 3.021,2.5 0.313,0.156 10 false *d 2.635,0.99 2.854,1.156 0.219,0.167 10 true A 3.094,0.802 3.313,0.969 0.219,0.167 10 true B
*a 90°
*b 0 to 3 mm (0 to 0.118 in.)
*c 2 to 7 mm (0.0787 to 0.276 in.)
*d No Contact Hose Clamps


Connect the air hose assembly to the turbine outlet elbow with 2 new hose clamps as shown in the illustration.

Torque:
9.5 N*m (97 kgf*cm, 84 in.*lbf)

NOTICE:

Do not reuse the hose clamp.


HINT:

Make sure the hose clamp is oriented as shown in the illustration.



b.

Install the air tube support bracket with the 2 bolts to the air hose assembly and radiator support.

Torque:
for bolt A : 8.0 N*m (82 kgf*cm, 71 in.*lbf)
for bolt B : 6.0 N*m (61 kgf*cm, 53 in.*lbf)


c.

Connect the air hose assembly to the intercooler assembly and lock the retainer.

NOTICE:

Securely insert the retainer so that the 4 locks are engaged. Then, pull and check that the locks are engaged and that the hose cannot be pulled out.


HINT:
A439809C01
1.031,2.667 0.969,2.5 0.969,2.5 0.771,2.5 true 2.521,2.625 2.458,2.458 2.458,2.458 2.26,2.458 true 1.115,3.073 1.115,2.896 true 2.771,3.073 2.771,2.896 true 0.813,1.906 1.125,2.063 0.313,0.156 10 false *a 2.365,1.906 2.677,2.063 0.313,0.156 10 false *b 0.583,2.385 0.781,2.583 0.198,0.198 10 true *c 2.063,2.354 2.26,2.552 0.198,0.198 10 true *c 1.031,3.083 1.229,3.281 0.198,0.198 10 true *d 2.677,3.094 2.875,3.292 0.198,0.198 10 true *d
*a Correct
*b Incorrect
*c Retainer End
*d Stopper


Make sure that the retainer end contacts the stopper as shown in the illustration.



Hide 16546 13.INSTALL RADIATOR PROTECTOR (w/o Air Conditioning System)

Hide 53209B 14.INSTALL HOOD LOCK SUPPORT BRACE SUB-ASSEMBLY

Hide 88590D 16.INSTALL BLOWER ASSEMBLY WITH SHROUD (w/ Condenser Fan)

Hide 86510 17.INSTALL HIGH PITCHED HORN ASSEMBLY (for 2-piece Type)

Hide 86520 18.INSTALL LOW PITCHED HORN ASSEMBLY

Hide 51466 19.INSTALL UPPER RADIATOR SUPPORT BRACE LH (for Wagon)

Hide 51465 20.INSTALL UPPER RADIATOR SUPPORT BRACE RH (for Wagon)

Hide 52021 21.INSTALL FRONT BUMPER REINFORCEMENT SUB-ASSEMBLY