This DTC is stored when the blind spot monitor sensor LH detects an open in the outer rear view mirror indicator LH.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| C1AB4 | Open in Outer Mirror Indicator(Master) | Both of the following conditions are met:
·
The blind spot monitor system is on ·
The current flowing to the indicator is below a specified value when indicator operation voltage is being sent to the indicator |
·
Outer mirror LH (outer rear view mirror indicator LH) ·
Outer mirror retractor LH (w/o Panoramic View Monitor System) ·
Harness or connector ·
Blind spot monitor sensor LH ·
Outer rear view mirror assembly LH (w/ Panoramic View Monitor System) |
When checking for DTCs, make sure that the blind spot monitor system is turned on.
Recheck for DTCs and check if the same DTC is output again.
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>BLIND SPOT MONITOR SYSTEM>DTC CHECK / CLEAR
No DTCs are output.
| Result | Proceed to |
|---|---|
| OK | A |
| NG (w/o Panoramic View Monitor System) | B |
| NG (w/ Panoramic View Monitor System) | C |
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
C
Disconnect the e2 blind spot monitor sensor LH connector.
Disconnect the R20 outer rear view mirror assembly LH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| e2-4 (OMIL) - R20-1 (BSL+) | Always | Below 1 Ω |
| R20-11 (E) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the outer mirror retractor LH.
Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR>DISASSEMBLY
Inspect the outer mirror retractor LH.
Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the outer mirror LH (outer rear view mirror indicator LH).
Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR GLASS>REMOVAL
Inspect the outer mirror LH (outer rear view mirror indicator LH).
Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR GLASS>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the e2 blind spot monitor sensor LH connector.
Disconnect the R23 outer rear view mirror assembly LH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| e2-4 (OMIL) - R23-7 (BSL+) | Always | Below 1 Ω |
| R23-12 (E) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the outer rear view mirror assembly LH.
Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR>REMOVAL
Inspect the outer rear view mirror assembly LH.
Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the outer mirror LH (outer rear view mirror indicator LH).
Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR GLASS>REMOVAL
Inspect the outer mirror LH (outer rear view mirror indicator LH).
Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR GLASS>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG