Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ EGR Cooler) › from 2019.06
RM35X0E _51 Engine / Hybrid System _078856 1GD-FTV ENGINE CONTROL _0388653 ECD SYSTEM(w/ EGR Cooler) L

1GD-FTV ENGINE CONTROL  ECD SYSTEM(w/ EGR Cooler)  PRECAUTION  


INITIALIZATION AND REGISTRATION


NOTICE:

When replacing the ECM and/or any other components in the following chart, perform the corresponding utility items.


HINT:

When the ECM and one or more other components are replaced at the same time, perform the following utility items by following the instructions shown on the GTS display, starting with the ECM.

Replacement Part Utility Item
ECM
·

Learning Values Save

(Click here)

·

Learning Values Write

(Click here)

·

VIN Registration

(Click here)


Engine assembly
·

Clear Crank Time Compensation Learning Value Data

Click here(Click here)

·

Input Injector Compensation Code

(Click here)

·

Pilot Quantity Learning

(Click here)


Crankshaft angle sensor plate Clear Crank Time Compensation Learning Value Data
Click here(Click here)
Injector assembly
·

Input Injector Compensation Code

(Click here)

·

Pilot Quantity Learning

(Click here)


Diesel throttle body assembly Initialization
Click here(Click here)
Electric EGR control valve assembly
Turbocharger sub-assembly or turbocharger nozzle vane control actuator


HINT:

When the ECM must be replaced, before replacing the ECM, perform the "Learning Values Save" function using the GTS. Then after installing the new ECM, perform all of the initializations/registrations for the "Learning Values Write" function by following the instructions shown on the GTS display.



INJECTOR COMPENSATION CODE


HINT:
·

Each injector assembly has different fuel injection characteristics. In order to optimize fuel injection performance, the ECM compensates for these differences by adjusting the fuel injection duration of each injector assembly according to its compensation code. Injector compensation codes are unique, 30-digit, alphanumeric values printed on the head portion of each injector assembly.

·

If an incorrect injector compensation code is input into the ECM, the engine may rattle or engine idling may become rough. In addition, engine failure may occur and the life of the engine may be shortened.



a.
A340465C01
1.094,0.865 0.948,0.49 0.948,0.49 0.813,0.49 false 0.083,0.083 0.302,0.271 0.219,0.188 10 false *a 0.625,0.427 0.938,0.625 0.313,0.198 10 false *b
*a Example
*b Injector Compensation Code


When an injector assembly is replaced, the injector compensation code must be input into the ECM.

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ EGR Cooler)>REGISTRATION


b.

When the ECM is replaced, all of the existing injector compensation codes must be input into the new ECM.

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ EGR Cooler)>REGISTRATION



PILOT QUANTITY LEARNING


HINT:
·

By performing "Pilot Quantity Learning", the injection volume for each cylinder is precisely adjusted so that the engine runs smoothly. The "Pilot Quantity Learning" information is stored in the EEPROM of the ECM.

·

If an incorrect pilot quantity learning value is input into the ECM, the engine may rattle or engine idling may become rough.



a.

When an injector assembly is replaced, the injector compensation code must be input to the ECM, and then pilot quantity learning must be performed.

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ EGR Cooler)>REGISTRATION


b.

When the ECM is replaced, all of the existing injector pilot quantity learning values must be input into the new ECM.

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ EGR Cooler)>REGISTRATION



WHEN USING GTS


CAUTION:

Observe the following items for safety reasons:

-

Before using the GTS, read the instruction manual.

-

Prevent the GTS cable from being caught on the pedals, shift lever or steering wheel when driving with the GTS connected to the vehicle.

-

When driving the vehicle for testing purposes using the GTS, 2 persons are required. One drives the vehicle, and the other operates the GTS.





IGNITION SWITCH EXPRESSIONS


HINT:

The type of ignition switch used on this model differs depending on the specifications of the vehicle. The expressions listed in the table below are used in this section.


Expression Ignition Switch (Position) Engine Switch (Condition)
Ignition Switch off LOCK Off (Lock)
Ignition Switch ACC ACC On (ACC)
Ignition Switch ON ON On (IG)
Engine Start START On (Start)