Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › ECD SYSTEM (for Water Cooled Type Intercooler) › from 2020.05
RM35X0E _51 Engine / Hybrid System _078856 1GD-FTV ENGINE CONTROL _0412266 ECD SYSTEM(for Water Cooled Type Intercooler) C

1GD-FTV ENGINE CONTROL  ECD SYSTEM(for Water Cooled Type Intercooler)  P010512  Manifold Absolute Pressure/Barometric Pressure Sensor Circuit Short to Battery  P010514  Manifold Absolute Pressure/Barometric Pressure Sensor Circuit Short to Ground or Open  


DESCRIPTION

A208461E08
0.417,0.406 0.708,0.646 0.292,0.24 10 false V 0.219,0.833 0.635,1.073 0.417,0.24 10 false 3.586 0.219,1.875 0.76,2.135 0.542,0.26 10 false 0.386 1.031,2.323 1.292,2.51 0.26,0.188 10 false 40 2.333,2.323 2.667,2.552 0.333,0.229 10 false 320 0.979,2.667 1.292,2.833 0.313,0.167 10 false 300 0.938,2.823 1.344,3.052 0.406,0.229 10 false (11.8) 2.281,2.833 2.719,3.052 0.438,0.219 10 false (94.5) 2.854,2.833 3.354,3.042 0.5,0.208 10 false (in.Hg) 2.854,2.531 3.354,2.75 0.5,0.219 10 false mmHg 2.875,2.115 3.229,2.302 0.354,0.188 10 false kPa 2.844,2.26 3.271,2.479 0.427,0.219 10 false (abs) 2.292,2.677 2.646,2.896 0.354,0.219 10 false 2400 1.333,3.063 2.219,3.323 0.885,0.26 10 false Air Pressure

The manifold absolute pressure sensor detects the intake manifold pressure. The ECM determines the basic injection volume and injection advance timing based on the voltage output by the manifold absolute pressure sensor.

The manifold absolute pressure sensor monitors the absolute pressure inside the intake manifold (default is 0 kPa [0 mmHg, 0 in.Hg]).

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P010512 Manifold Absolute Pressure/Barometric Pressure Sensor Circuit Short to Battery Manifold absolute pressure sensor voltage is 4.8 V or higher for more than 0.5 seconds (1 trip detection logic).
·

Open or short in manifold absolute pressure sensor circuit

·

Manifold absolute pressure sensor

·

ECM


Comes on DTC stored SAE Code: P0108
P010514 Manifold Absolute Pressure/Barometric Pressure Sensor Circuit Short to Ground or Open Manifold absolute pressure sensor voltage is 0.1 V or less for more than 0.5 seconds (1 trip detection logic).
·

Open or short in manifold absolute pressure sensor circuit

·

Manifold absolute pressure sensor

·

ECM


Comes on DTC stored SAE Code: P0107

Related Data List
DTC No. Data List
P010512
P010514
·

Intake Manifold Absolute Pressure

·

Atmospheric Pressure



HINT:
·

If DTC P010512 and/or P010514 is stored, the following symptoms may appear:

-

Misfire

-

Combustion noise

-

Black smoke

-

White smoke

-

Lack of power


·

When DTC P010512 or P010514 is stored, check the intake manifold pressure by entering the following menus: Powertrain / Engine / Data List / Intake Manifold Absolute Pressure.

Reference
GTS Displayed Malfunction
23 kPa (173 mmHg, 6.79 in.Hg)
·

Open in VC circuit

·

Open in PIM circuit

·

Short in PIM circuit


418 kPa (3135 mmHg, 123.44 in.Hg)
·

Open in E circuit





CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P010512
P010514
2 seconds after engine is started, race engine for 1 second

WIRING DIAGRAM

A402979E31
1.146,1.719 1.677,1.927 0.531,0.208 10 false PIM 1.198,1.031 1.729,1.24 0.531,0.208 10 false VC 1.281,2.49 1.813,2.698 0.531,0.208 10 false E 4.75,0.938 5.281,1.146 0.531,0.208 10 false VCPM 4.5,0.938 5.031,1.146 0.531,0.208 10 false 28 4.51,2.396 5.042,2.604 0.531,0.208 10 false 19 4.49,1.625 5.021,1.833 0.531,0.208 10 false 18 4.75,2.594 5.281,2.802 0.531,0.208 10 false EPIM 4.75,1.625 5.281,1.833 0.531,0.208 10 false PIM 5.5,3.292 6.031,3.5 0.531,0.208 10 false ECM 5.5,3.125 6.031,3.333 0.531,0.208 10 false E5 0.073,2.896 0.604,3.104 0.531,0.208 10 false E40 0.073,3.073 2.667,3.458 2.594,0.385 10 false Manifold Absolute Pressure Sensor 1.5,0.927 2.031,1.135 0.531,0.208 10 false 3 1.51,1.615 2.042,1.823 0.531,0.208 10 false 2 1.51,2.396 2.042,2.604 0.531,0.208 10 false 1 6.115,0.688 6.646,0.896 0.531,0.208 10 false 5 V 4.917,2.125 5.833,2.323 0.917,0.198 10 false 200 kΩ

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (for Water Cooled Type Intercooler)>REGISTRATION) and initialization (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (for Water Cooled Type Intercooler)>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING GTS (INTAKE MANIFOLD ABSOLUTE PRESSURE)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Data List / Intake Manifold Absolute Pressure.

Powertrain > Engine > Data List
Tester Display
Intake Manifold Absolute Pressure
50003 372 385

d.

Read the value.

OK:

Same as the actual atmospheric pressure.


HINT:
·

Standard atmospheric pressure is 101 kPa. For every 100 m increase in elevation, pressure drops by 1 kPa. This varies by weather (high atmospheric pressure, low atmospheric pressure).

·

Also, check "Atmospheric Pressure" in the Data List.




Result:
Proceed to
OK
NG



OK

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

NG

2.CHECK ECM TERMINAL VOLTAGE (VC TERMINAL)
2.CHECK ECM TERMINAL VOLTAGE (VC TERMINAL)
a.
A204467C98
0.677,1.135 1.042,1.385 0.365,0.25 1.24,1.75 1.49,1.292 true 2.177,1.729 1.948,1.292 true 0.167,0.208 0.479,0.406 0.313,0.198 10 false *a 0.729,1.177 1.052,1.375 0.323,0.198 10 false E40 1.177,1.75 1.479,2 0.302,0.25 10 false E 2.198,1.74 2.51,1.938 0.313,0.198 10 false VC
*a Front view of wire harness connector
(to Manifold Absolute Pressure Sensor)


Disconnect the manifold absolute pressure sensor connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
E40-3 (VC) - E40-1 (E) Ignition switch ON 4.5 to 5.5 V



Result:
Proceed to
OK
NG



OK

3.INSPECT MANIFOLD ABSOLUTE PRESSURE SENSOR (PIM VOLTAGE)

NG

7.CHECK ECM (POWER SOURCE OF MANIFOLD ABSOLUTE PRESSURE SENSOR)
3.INSPECT MANIFOLD ABSOLUTE PRESSURE SENSOR (PIM VOLTAGE)
a.
A372026C54
0.323,0.865 0.74,1.115 0.417,0.25 1.177,2.375 0.573,1.646 true 0.354,2.375 0.521,1.656 true 0.406,0.906 0.865,1.104 0.458,0.198 10 false E5 0.135,2.385 1.188,2.656 1.052,0.271 10 false 19 (EPIM) 0.094,0.063 0.406,0.26 0.313,0.198 10 false *a 0.917,2.396 1.635,2.646 0.719,0.25 10 false 18 (PIM)
*a Component with harness connected
(ECM)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
E5-18 (PIM) - E5-19 (EPIM) Ignition switch ON 0.8 to 1.5 V



Result:
Proceed to
OK
NG



OK

8.REPLACE ECM

NG

4.CHECK HARNESS AND CONNECTOR (MANIFOLD ABSOLUTE PRESSURE SENSOR - ECM)
4.CHECK HARNESS AND CONNECTOR (MANIFOLD ABSOLUTE PRESSURE SENSOR - ECM)
a.

Disconnect the manifold absolute pressure sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E40-2 (PIM) - E5-18 (PIM) Always Below 1 Ω
E40-1 (E) - E5-19 (EPIM) Always Below 1 Ω
E40-2 (PIM) or E5-18 (PIM) - Body ground and other terminals Always 10 kΩ or higher
E40-1 (E) or E5-19 (EPIM) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK ECM (CHECK RESISTANCE)

NG

10.REPAIR OR REPLACE HARNESS OR CONNECTOR
5.CHECK ECM (CHECK RESISTANCE)
a.

Disconnect the manifold absolute pressure sensor connector.


b.
A204467C74
0.677,1.135 1.042,1.385 0.365,0.25 1.24,1.75 1.49,1.292 true 2.177,1.729 1.948,1.292 true 1.708,1.729 1.688,1.281 true 0.167,0.208 0.479,0.406 0.313,0.198 10 false *a 0.729,1.177 1.052,1.375 0.323,0.198 10 false E40 1.177,1.75 1.479,2 0.302,0.25 10 false E 2.198,1.74 2.51,1.938 0.313,0.198 10 false VC 1.615,1.76 2,1.969 0.385,0.208 10 false PIM
*a Front view of wire harness connector
(to Manifold Absolute Pressure Sensor)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
E40-3 (VC) - E40-2 (PIM) Ignition switch off No short or no open circuit
E40-2 (PIM) - E40-1 (E) Ignition switch off No short or no open circuit



Result:
Proceed to
OK
NG



OK

6.REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR

NG

8.REPLACE ECM
6.REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR
a.

Result:
Proceed to
NEXT



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
7.CHECK ECM (POWER SOURCE OF MANIFOLD ABSOLUTE PRESSURE SENSOR)
a.
A372026C55
0.323,0.865 0.74,1.115 0.417,0.25 0.542,2.583 0.531,1.646 true 1.052,2.25 0.573,1.698 true 0.406,0.906 0.865,1.104 0.458,0.198 10 false E5 1.115,2.302 1.802,2.51 0.688,0.208 10 false 28 (VCPM) 0.094,0.063 0.406,0.26 0.313,0.198 10 false *a 0.177,2.594 0.896,2.844 0.719,0.25 10 false 19 (EPIM)
*a Component with harness connected
(ECM)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
E5-28 (VCPM) - E5-19 (EPIM) Ignition switch ON 4.5 to 5.5 V



Result:
Proceed to
OK
NG



NG

8.REPLACE ECM

OK

10.REPAIR OR REPLACE HARNESS OR CONNECTOR
8.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

c.

Turn the ignition switch off for 30 seconds or more.


d.

Turn the GTS off.


e.

Turn the ignition switch to ON for 3 seconds and turn the GTS on.


f.

After the engine is started for 2 seconds, race the engine for 1 second.


g.

Confirm that the DTC is not output again.

HINT:

Perform the following procedure using the GTS to determine whether or not the DTC judgment has been carried out.


i.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.

Powertrain > Engine > Utility
Tester Display
All Readiness
50005 372 20

ii.

Input DTC P010512 or P010514.


iii.

Check that STATUS is NORMAL. If STATUS is INCOMPLETE, race the engine for 1 minute, and then idle the engine for 5 minutes.



Result:
Proceed to
NEXT



NEXT

END

10.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED