The crankshaft position sensor system consists of a crank angle sensor plate and Magneto-Resistive Element (MRE) type sensor. The crank angle sensor plate has 34 teeth at 10° intervals (2 teeth are missing for detecting top dead center), and is installed on the crankshaft. The crankshaft position sensor generates 34 signals per crankshaft revolution. The ECM uses the NE signal to detect the crankshaft position and engine speed.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
|---|---|---|---|---|---|---|
| P03351F | Crankshaft Position Sensor "A" Circuit Intermittent | Under conditions (a), (b) and (c), no crankshaft position sensor signal is sent to the ECM for 0.05 seconds or more (1 trip detection logic):
(a) Engine speed is 1000 rpm or more. (b) Starter signal is off. (c) 3 seconds or more have elapsed since the starter signal switched from on to off. |
·
Crankshaft position sensor ·
Crankshaft (crank angle sensor plate) ·
ECM |
Does not come on | DTC stored | SAE Code: P0339 |
| P03352A | Crankshaft Position Sensor "A" Signal Stuck in Range | No crankshaft position sensor signal to the ECM while cranking (1 trip detection logic). | ·
Crankshaft position sensor ·
Crankshaft (crank angle sensor plate) ·
ECM |
Comes on | DTC stored | SAE Code: P0335 |
| P033531 | Crankshaft Position Sensor "A" No Signal | The engine stalls and the engine speed signal value decreases rapidly (1 trip detection logic). | ·
Crankshaft position sensor ·
Crankshaft (crank angle sensor plate) ·
ECM |
Comes on | DTC stored | SAE Code: P0335 |
| DTC No. | Data List |
|---|---|
| P03351F
P03352A P033531 |
Engine Speed |
If DTC P03351F, P03352A and/or P033531 is stored, the following symptoms may appear:
Difficulty starting
Misfire
Combustion noise
Black smoke
White smoke
Lack of power
Reference: Inspection using an oscilloscope.
The correct waveform is as shown.
| ECM Terminal Name | Between G2+ and G2-
Between NE+ and NE- |
| Tester Range | 2 V/DIV., 20 msec./DIV. |
| Condition | Idling with warm engine |
If there is no signal from the crankshaft position sensor despite the crankshaft revolving, the ECM interprets this as a malfunction of the sensor.
| DTC No. | DTC Detection Drive Pattern |
|---|---|
| P03351F | Engine running at 1000 rpm or higher with vehicle stationary |
| P03352A
P033531 |
Crank or start engine |
Refer to DTC P03402A.
After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (for Water Cooled Type Intercooler)>REGISTRATION) and initialization (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (for Water Cooled Type Intercooler)>INITIALIZATION).
If no problem is found by this diagnostic troubleshooting procedure, check for problems by referring to the engine mechanical section.
The engine speed can be checked by using the GTS. To perform the check, follow the procedures below:
Connect the GTS to the DLC3.
Start the engine.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Data List / Primary / Engine Speed.
The engine speed may be indicated as zero despite the engine running normally. This is caused by a lack of NE signals from the crankshaft position sensor. Alternatively, the engine speed may be indicated as lower than the actual engine speed if the crankshaft position sensor output voltage is insufficient.
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Check the engine cranking condition.
| Result | Proceed to |
|---|---|
| Cranking is OK. | A |
| Does not crank at all.* | B |
*: When the engine cannot crank, there may be a malfunction in the starter assembly.
A
B
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Data List / Primary / Engine Speed.
| Tester Display |
|---|
| Engine Speed |
Start the engine.
Read the values displayed on the GTS while the engine is running.
Correct values are displayed.
To check the engine speed change, display the graph on the GTS.
If the engine does not start, check the engine speed while cranking.
If the engine speed indicated on the GTS remains at zero (0), there may be an open or short in the crankshaft position sensor circuit.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs.
Turn the ignition switch off and wait for at least 30 seconds.
Start the engine and run it at 1000 rpm or higher for 5 seconds or more.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
|---|---|
| DTC is not output | A |
| DTC P03351F, P03352A and/or P033531 is output | B |
A
B
Inspect the ECM using an oscilloscope.
While the engine is idling, check the waveform between the terminals of the ECM connector.
| *a | Component with harness connected
(ECM) |
- | - |
| Tester Connection | Tester Range | Condition | Specified Condition |
|---|---|---|---|
| E8-28 (NE+) - E8-19 (NE-) | 2 V/DIV.
50 msec./DIV. |
Cranking to idling | Correct waveform as shown in illustration |
| Proceed to |
|---|
| OK |
| NG |
NG
OK
| *a | Clearance |
Check the crankshaft position sensor installation condition.
Crankshaft position sensor is installed correctly.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the teeth of the crank angle sensor plate.
Crank angle sensor plate does not have any cranks or deformation.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the crankshaft position sensor.
Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>CRANKSHAFT POSITION SENSOR>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs.
Turn the ignition switch off for 30 seconds or more.
Start the engine and run it at 1000 rpm or higher for 5 seconds or more.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Confirm that the DTC is not output.
| Proceed to |
|---|
| NEXT |
NEXT
Replace the crankshaft.
Click hereEngine / Hybrid System>1GD-FTV (ENGINE MECHANICAL)>CYLINDER BLOCK>DISASSEMBLY
| Proceed to |
|---|
| NEXT |
NEXT
Securely reinstall the crankshaft position sensor.
Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>CRANKSHAFT POSITION SENSOR>INSTALLATION
| Proceed to |
|---|
| NEXT |
NEXT
Replace the ECM.
Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT