Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › ECD SYSTEM (for Water Cooled Type Intercooler) › from 2020.05
RM35X0E _51 Engine / Hybrid System _078856 1GD-FTV ENGINE CONTROL _0412266 ECD SYSTEM(for Water Cooled Type Intercooler) C

1GD-FTV ENGINE CONTROL  ECD SYSTEM(for Water Cooled Type Intercooler)  P245211  Particulate Filter Pressure Sensor "A" Circuit Short to Ground  P245215  Particulate Filter Pressure Sensor "A" Circuit Short to Battery or Open  


DESCRIPTION

HINT:
·

For more information on the differential pressure sensor and Diesel Particulate Filter (DPF), refer to the following procedures.

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (for Water Cooled Type Intercooler)>SYSTEM DESCRIPTION

·

If P245211 and/or P245215 is present, refer to the DTC chart for DPF system.

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (for Water Cooled Type Intercooler)>SYSTEM DESCRIPTION


A128654E16
4.417,1.208 4.229,1.385 false 4.948,1.115 4.875,1.365 4.875,1.365 4.969,1.365 false 4.406,1.167 4.24,1.208 false 5.5,3.042 5.271,2.552 5.271,2.552 5.406,2.552 false 1.302,2.26 0.802,2.917 false 2.76,2.552 2.885,2.917 false 1.302,0.708 2.125,0.885 0.823,0.177 10 false Exhaust Gas 2.917,0.708 3.26,0.875 0.344,0.167 10 false ECM 0.375,2.938 1.448,3.271 1.073,0.333 10 false DPF Catalytic Converter 2.094,2.958 3.823,3.146 1.729,0.188 10 false Differential Pressure Sensor 3.854,0.052 5.708,0.24 1.854,0.188 10 false Property of Output Voltage: 5.01,1.281 6.198,1.583 1.188,0.302 10 false Stores P245215 5.448,2.479 6.51,2.781 1.063,0.302 10 false Stores P245211 4.052,0.635 6.073,0.813 2.021,0.177 10 false Differential Pressure Voltage (V) 4.021,0.938 4.396,1.104 0.375,0.167 10 false 5.000 3.865,1.135 4.24,1.302 0.375,0.167 10 false 4.800 3.865,1.333 4.24,1.5 0.375,0.167 10 false 4.650 4.021,2.396 4.396,2.563 0.375,0.167 10 false 1.530 4.021,2.604 4.396,2.771 0.375,0.167 10 false 0.750 4.021,2.75 4.396,2.917 0.375,0.167 10 false 0.555 4.021,2.896 4.396,3.063 0.375,0.167 10 false 0.400 4.292,3.115 4.396,3.271 0.104,0.156 10 false 0 4.771,3.24 4.875,3.396 0.104,0.156 10 false 0 4.531,3.24 4.708,3.406 0.177,0.167 10 false -5 4.938,3.24 5.229,3.406 0.292,0.167 10 false 20.0 6.479,3.25 6.865,3.417 0.385,0.167 10 false 100.0 4.323,3.427 6.813,3.625 2.49,0.198 10 false Exhaust Gas Differential Pressure (kPa)


The two sensing chambers of the differential pressure sensor are mounted to monitor the pressure before and after the DPF catalytic converter. The sensor itself is not located on the engine assembly in order to reduce the influence of vibration.

The ECM compares the exhaust gas pressure before and after the DPF catalytic converter by monitoring the pressure using the upstream and downstream sensing chambers of the differential pressure sensor. If the difference between the pressure before and after the DPF catalytic converter exceeds a predetermined level, the ECM judges that the catalytic converter is clogged with particulate matter (PM). When the ECM judges that a partially clogged condition exists, the ECM begins to perform PM forced regeneration.

When the output voltage of the sensor deviates from the normal operating range, the ECM interprets this as a malfunction of the sensor circuit, and sets DTC P245211 or P245215, and illuminates the MIL.

HINT:

If the vacuum hoses of the differential pressure sensor are incorrectly connected (crossed), the ECM interprets this as an abnormal pressure difference, DTC P24521C (Particulate Filter Pressure Sensor "A" Circuit Voltage Out of Range) is stored and the MIL illuminates.


DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P245211 Particulate Filter Pressure Sensor "A" Circuit Short to Ground Differential pressure sensor output voltage is below 0.4 V for 3 seconds or more (1 trip detection logic).
·

Open or short in differential pressure sensor circuit

·

Differential pressure sensor

·

ECM


Comes on DTC stored SAE Code: P2454
P245215 Particulate Filter Pressure Sensor "A" Circuit Short to Battery or Open Differential pressure sensor output voltage is higher than 4.8 V for 3 seconds or more (1 trip detection logic).
·

Open or short in differential pressure sensor circuit

·

Differential pressure sensor

·

ECM


Comes on DTC stored SAE Code: P2455

Related Data List
DTC No. Data List
P245211
P245215
Particulate Filter Differential Pressure Bank 1

HINT:
·

DTC P24521C (Particulate Filter Pressure Sensor "A" Circuit Voltage Out of Range) will be stored if there is incorrect vacuum hose routing to the differential pressure sensor.

·

After confirming DTC P245211 and P245215, check the differential pressure in the "Powertrain / Engine / Data List / Diesel Exhaust / Particulate Filter Differential Pressure Bank 1" menu using the GTS.


Reference:
Condition Particulate Filter Differential Pressure Bank 1 Output Sensor Condition
Ignition switch ON Approximately 0 kPa Normal
Always -5 kPa or less or higher than 99 kPa Open or short circuit
4000 rpm (No engine load) Negative output Incorrect hose routing


MONITOR DESCRIPTION

In order to detect abnormality in the differential pressure sensor, the ECM always monitors the output voltage from the sensor. When the sensor output voltage deviates from the normal operating range (between 0.4 V and 4.8 V) for more than 3 seconds, the ECM interprets this as a malfunction in the sensor circuit and illuminates the MIL.

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P245211
P245215
Ignition switch ON for 5 seconds

WIRING DIAGRAM

A379958E05
0.698,2.854 1.313,3.052 0.615,0.198 10 false E43 0.688,3.01 2.49,3.208 1.802,0.198 10 false Differential Pressure Sensor 1.479,0.917 1.792,1.115 0.313,0.198 10 false VC 1.781,1.031 2.094,1.229 0.313,0.198 10 false 3 1.385,1.615 1.875,1.813 0.49,0.198 10 false PEX 1.49,2.385 1.802,2.583 0.313,0.198 10 false E2 1.792,2.49 2.104,2.688 0.313,0.198 10 false 1 1.792,1.729 2.104,1.927 0.313,0.198 10 false 2 4.896,3.021 5.396,3.219 0.5,0.198 10 false E7 4.906,3.229 5.427,3.427 0.521,0.198 10 false ECM 4.677,0.802 5.271,1 0.594,0.198 10 false VCPX 4.667,1.5 5.156,1.698 0.49,0.198 10 false PEX 4.688,2.292 5.229,2.51 0.542,0.219 10 false EPEX 4.385,1.042 4.698,1.24 0.313,0.198 10 false 32 4.406,1.729 4.719,1.927 0.313,0.198 10 false 27 4.427,2.51 4.74,2.708 0.313,0.198 10 false 26

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (for Water Cooled Type Intercooler)>REGISTRATION) and initialization (Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (for Water Cooled Type Intercooler)>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK TERMINAL VOLTAGE (POWER SOURCE OF DIFFERENTIAL PRESSURE SENSOR)
a.
A204467C75
0.365,1.063 0.802,1.323 0.438,0.26 1.969,1.24 2.406,1.656 true 1.479,1.271 1.188,1.656 true 0.333,0.25 0.583,0.406 0.25,0.156 10 false *a 2.406,1.656 2.667,1.823 0.26,0.167 10 false VC 0.438,1.115 0.865,1.281 0.427,0.167 10 false E43 1.01,1.656 1.271,1.823 0.26,0.167 10 false E2
*a Front view of wire harness connector
(to Differential Pressure Sensor)


Disconnect the differential pressure sensor connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
E43-3 (VC) - E43-1 (E2) Ignition switch ON 4.5 to 5.5 V



Result:
Proceed to
OK
NG



OK

2.CHECK DIFFERENTIAL PRESSURE SENSOR (PEX VOLTAGE)

NG

9.CHECK ECM (POWER SOURCE OF DIFFERENTIAL PRESSURE SENSOR)
2.CHECK DIFFERENTIAL PRESSURE SENSOR (PEX VOLTAGE)
a.
A372026C67
1.219,0.854 1.635,1.104 0.417,0.25 1.823,2.344 1.323,1.625 true 1.063,2.344 1.271,1.635 true 0.094,0.063 0.406,0.26 0.313,0.198 10 false *a 1.354,0.896 1.813,1.094 0.458,0.198 10 false E7 0.677,2.427 1.406,2.656 0.729,0.229 10 false 27 (PEX) 1.729,2.438 2.448,2.635 0.719,0.198 10 false 26 (EPEX)
*a Component with harness connected
(ECM)


Turn the ignition switch to ON.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
E7-27 (PEX) - E7-26 (EPEX) Ignition switch ON 0.4 to 4.8 V



Result:
Proceed to
OK
NG



OK

3.REPLACE ECM

NG

5.CHECK HARNESS AND CONNECTOR (DIFFERENTIAL PRESSURE SENSOR - ECM)
3.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

4.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
4.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

e.

Turn the ignition switch off and wait for 30 seconds.


f.

Turn the ignition switch to ON and wait for 3 seconds.


g.

Turn the GTS on.


h.

Enter the following menus: Powertrain / Engine / Trouble Codes.

Powertrain > Engine > Trouble Codes
50001 372

i.

Confirm that the DTC is not output.


Result:
Proceed to
NEXT



NEXT

END

5.CHECK HARNESS AND CONNECTOR (DIFFERENTIAL PRESSURE SENSOR - ECM)
a.

Disconnect the differential pressure sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E43-2 (PEX) - E7-27 (PEX) Always Below 1 Ω
E43-3 (VC) - E7-32 (VCPX) Always Below 1 Ω
E43-1 (E2) - E7-26 (EPEX) Always Below 1 Ω
E43-2 (PEX) or E7-27 (PEX) - Body ground and other terminals Always 10 kΩ or higher
E43-3 (VC) or E7-32 (VCPX) - Body ground and other terminals Always 10 kΩ or higher
E43-1 (E2) or E7-26 (EPEX) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK ECM (CHECK RESISTANCE)

NG

8.REPAIR OR REPLACE HARNESS OR CONNECTOR
6.CHECK ECM (CHECK RESISTANCE)
a.
A204467C76
0.365,1.063 0.802,1.323 0.438,0.26 1.969,1.24 2.448,1.708 true 1.458,1.271 0.969,1.729 true 1.698,1.281 1.708,1.781 true 0.333,0.25 0.583,0.406 0.25,0.156 10 false *a 2.396,1.719 2.656,1.885 0.26,0.167 10 false VC 0.458,1.115 0.885,1.281 0.427,0.167 10 false E43 0.854,1.729 1.115,1.896 0.26,0.167 10 false E2 1.583,1.813 1.927,2.01 0.344,0.198 10 false PEX
*a Front view of wire harness connector
(to Differential Pressure Sensor)


Disconnect the differential pressure sensor connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E43-3 (VC) - E43-2 (PEX) Ignition switch off No short or no open circuit
E43-2 (PEX) - E43-1 (E2) Ignition switch off No short or no open circuit



Result:
Proceed to
OK
NG



OK

7.REPLACE DIFFERENTIAL PRESSURE SENSOR

NG

3.REPLACE ECM
7.REPLACE DIFFERENTIAL PRESSURE SENSOR

Result:
Proceed to
NEXT



NEXT

4.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
8.REPAIR OR REPLACE HARNESS OR CONNECTOR
Result:
Proceed to
NEXT



NEXT

4.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
9.CHECK ECM (POWER SOURCE OF DIFFERENTIAL PRESSURE SENSOR)
a.
A372026C68
1.219,0.854 1.635,1.104 0.417,0.25 1.823,2.344 1.323,1.625 true 1.063,2.344 1.271,1.698 true 0.094,0.063 0.406,0.26 0.313,0.198 10 false *a 1.354,0.896 1.813,1.094 0.458,0.198 10 false E7 0.677,2.427 1.406,2.656 0.729,0.229 10 false 32 (VCPX) 1.729,2.438 2.448,2.635 0.719,0.198 10 false 26 (EPEX)
*a Component with harness connected
(ECM)


Turn the ignition switch to ON.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
E7-32 (VCPX) - E7-26 (EPEX) Ignition switch ON 4.5 to 5.5 V



Result:
Proceed to
OK
NG



NG

3.REPLACE ECM

OK

8.REPAIR OR REPLACE HARNESS OR CONNECTOR