Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › NITROGEN OXIDES SENSOR › from 2020.05
RM35X0E _51 Engine / Hybrid System _078856 1GD-FTV ENGINE CONTROL _0387404 NITROGEN OXIDES SENSOR A

1GD-FTV ENGINE CONTROL  NITROGEN OXIDES SENSOR  REMOVAL  


PROCEDURE

Hide 85110 1.REMOVE WINDSHIELD WIPER MOTOR ASSEMBLY

Hide 55701J 2.REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY

Hide 89463C 3.DISCONNECT NO. 1 NITROGEN OXIDES SENSOR

a.

for Air Cooled Type Intercooler (w/ Exhaust Gas Temperature Sensor for EGR):

i.
A443569

Disconnect the connector from the No. 1 nitrogen oxides sensor.


ii.

Remove the 2 bolt.


iii.

Detach the 5 clamps and disconnect the No. 1 nitrogen oxides sensor.



b.

for Water Cooled Type Intercooler:

i.
A454052C02
2.979,1.021 3.104,0.969 false
V100135

Connector
V100136

Bolt


Disconnect the connector from the No. 1 nitrogen oxides sensor.


ii.

Remove the 2 bolt.


iii.

Detach the 6 clamps and disconnect the No. 1 nitrogen oxides sensor.



Hide 25051 4.REMOVE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY (w/ Exhaust Gas Temperature Sensor for EGR)

Hide 89463C 5.REMOVE NO. 1 NITROGEN OXIDES SENSOR

CAUTION:

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.


a.
A443581N01
1.792,0.958 2.344,1.813 2.344,1.813 2.635,1.813 true 2.719,1.729 3.177,1.927 0.458,0.198 10 false SST

Using SST, remove the No. 1 nitrogen oxides sensor.

SST
09224-00012  


b.
A443582

Remove the 2 nuts, detach the clamp (cable tie), and then remove the No. 1 nitrogen oxides sensor from the exhaust sensor clamp bracket.


Hide 89463D 6.REMOVE NO. 2 NITROGEN OXIDES SENSOR

CAUTION:

To prevent burns, do not touch the engine, exhaust manifold or other high temperature components while the engine is hot.


a.
A455885C02
1.146,1.146 1.115,1.073 false 2.021,0.594 2.021,0.469 false
V100135

Bolt
V100136

Clip


Remove the 4 bolts, 4 clips and step plate cover sub-assembly RH.


b.
A440864

Disconnect the connector from the No. 4 exhaust gas temperature sensor.


c.
A440865

Detach the 2 clamps and disconnect the No. 4 exhaust gas temperature sensor from the sensor bracket.


d.
A457373C02
2.167,0.698 2.271,0.635 false
V100135

Connector
V100136

Bolt


Disconnect the connector from the No. 2 nitrogen oxides sensor.


e.

Remove the 2 bolts and sensor bracket.


f.
A443585N01
0.729,1.104 1.083,1.104 1.083,1.104 1.167,0.938 true 0.375,1.021 0.719,1.24 0.344,0.219 10 true SST

Using SST, remove the No. 2 nitrogen oxides sensor.

SST
09224-00012  


g.
A443584

Remove the 2 nuts, detach the 2 clamps and then remove the No. 2 nitrogen oxides sensor from the sensor bracket.