Do not remove the reserve tank cap (for Intercooler) or radiator drain cock plug (for Intercooler) while the engine and intercooler cooling radiator assembly are still hot. Pressurized, hot engine coolant (for Intercooler) and steam may be released and cause serious burns.
51447D
1.REMOVE CENTER NO. 4 ENGINE UNDER COVER
2.DRAIN ENGINE COOLANT
Do not remove the reserve tank cap (for Intercooler), radiator drain cock plug (for Intercooler) while the engine and intercooler cooling radiator assembly are still hot. Pressurized, hot engine coolant (for Intercooler) and steam may be released and cause serious burns.
| *a | Hose |
Connect a hose with an inside diameter of 9 mm (0.354 in.) to the radiator drain cock (for Intercooler) as shown in the illustration.
| *1 | Reserve Tank Cap (for Intercooler) |
| *2 | Radiator Drain Cock Plug (for Intercooler) |
Loosen the radiator drain cock plug (for Intercooler).
Remove the reserve tank cap (for Intercooler), and then drain the engine coolant (for Intercooler).
Tighten the radiator drain cock plug (for Intercooler) and remove the hose from the radiator drain cock (for Intercooler).
3.ADD ENGINE COOLANT
To prevent injury due to contact with an operating fan and generator V belt or cooling fan, keep your hands and clothing away from the fan and generator V belt and the fan when working in the engine compartment with the engine running or the ignition switch ON.
Before adding coolant, turn the A/C switch off. (w/ Air Conditioning System)
When using the GTS:
Slowly pour coolant into the intercooler reserve tank assembly.
2.2 liters (2.3 US qts, 1.9 Imp. qts)
Never use water as a substitute for coolant.
TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damage to the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology is a combination of low phosphates and organic acids).
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine and Transmission / Active Test / Control the Intercooler Water Pump.
While adding coolant so that the coolant level is kept near the FULL line in the intercooler reserve tank assembly, activate the electric water pump assembly for approximately 1 minute and then stop pump operation for 1 minute. At that time, check that air bubbles are discharged to the intercooler reserve tank assembly.
Repeat this operation approximately 3 times until the sound of the electric water pump assembly gets smaller and no more bubbles are visible from the intercooler reserve tank assembly or the coolant level in the intercooler reserve tank assembly stabilizes. When this condition is reached, this indicates that air is completely bled from the coolant system.
If the intercooler reserve tank assembly is filled excessively with coolant, coolant may spill out when the electric water pump assembly is stopped.
|
FULL Line |
When air is completely bled, add coolant up to the FULL line in the intercooler reserve tank assembly, and install the reserve tank cap (for Intercooler).
When not using the GTS:
Slowly pour coolant into the intercooler reserve tank assembly.
2.2 liters (2.3 US qts, 1.9 Imp. qts)
Never use water as a substitute for coolant.
TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damage to the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology is a combination of low phosphates and organic acids).
Install the reserve tank cap (for Intercooler). [*1]
Start the engine. [*2]
In order to operate the electric water pump assembly, maintain the engine speed at 2000 rpm or higher with the shift lever in N or P for 1 minute and then stop operation for 1 minute. Repeat this operation approximately 3 times until the sound of the electric water pump assembly gets smaller and no more bubbles are visible from the intercooler reserve tank assembly or the coolant level in the intercooler reserve tank assembly stabilizes. [*3]
Be careful as the radiator hoses are hot.
Keep your hands away from the cooling fan.
Make sure that the coolant level in the intercooler reserve tank assembly does not drop below the LOW line when the engine speed is 2000 rpm or higher.
Immediately after starting the engine, if the intercooler reserve tank assembly runs out of coolant, perform the following: 1) stop the engine, 2) wait until the coolant has cooled down, and 3) pour in coolant until it reaches the FULL line.
Stop the engine and wait until the coolant cools down to ambient temperature. [*4]
|
FULL Line |
Check that the coolant level is between the FULL and LOW line. [*5]
If the coolant level is lower than the LOW line, pour coolant of the specified concentration into the intercooler reserve tank assembly until it reaches the FULL line, and repeat the procedure from steps [*1] to [*5].
If the coolant level is above the FULL line, drain coolant so that the coolant level is between the FULL and LOW line.
4.INSPECT FOR COOLANT LEAK
51447D
5.INSTALL CENTER NO. 4 ENGINE UNDER COVER