Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM › from 2019.06
RM35X0E _57 Power Source / Network _078518 NETWORKING _0381088 CAN COMMUNICATION SYSTEM J

NETWORKING  CAN COMMUNICATION SYSTEM  Check Bus 4 Line  


DESCRIPTION

Symptom Trouble Area

*1: w/ Airbag System

*2: w/o Airbag System

*3: w/o VSC OFF Switch

*4: w/ Variable Flow Control Solenoid Valve

*5: w/ VSC OFF Switch

*6: w/ Tire Pressure Warning System (Tire Inflation Pressure Display Function)

There are ECUs or sensors that display a communication stop on the bus diagnostic screen. Or, there are ECUs or sensors that store a communication stop history on the "Detail" screen.
·

CAN bus lines or connector

·

Central gateway ECU (network gateway ECU)

·

Airbag sensor assembly*1

·

Brake actuator assembly (skid control ECU)

·

Combination switch ECU sub-assembly*3

·

Power steering ECU assembly*4

·

Steering sensor*5

·

Tire pressure warning ECU and receiver*6

·

No. 4 CAN junction connector

·

No. 2 CAN junction Terminal*2



WIRING DIAGRAM

C414818E01
0.885,0.469 1.5,0.667 0.615,0.198 10 false CA2H 0.906,1.042 1.521,1.24 0.615,0.198 10 false CA2L 0.75,2.188 1.365,2.385 0.615,0.198 10 false CANH 0.771,2.76 1.385,2.958 0.615,0.198 10 false CANL 5.958,4.406 6.573,4.604 0.615,0.198 10 false CANL 5.958,3.979 6.573,4.177 0.615,0.198 10 false CANH 5.958,2.688 6.573,2.885 0.615,0.198 10 false CANL 5.948,2.26 6.563,2.458 0.615,0.198 10 false CANH 6.042,0.969 6.656,1.167 0.615,0.198 10 false CANL 6.031,0.563 6.646,0.76 0.615,0.198 10 false CANH 5.521,1.302 7.115,1.75 1.594,0.448 10 false Brake Actuator Assembly (Skid Control ECU) 5.198,2.99 7.125,3.375 1.927,0.385 10 false Combination Switch ECU Sub-assembly*3, Steering Sensor*5 2.885,6.604 4.875,6.979 1.99,0.375 10 false No. 4 CAN Junction Connector 5.635,6.448 7.01,6.958 1.375,0.51 10 false Tire Pressure Warning ECU and Receiver*6 0.25,1.344 2.198,1.719 1.948,0.375 10 false Central Gateway ECU (Network Gateway ECU) 0.792,3.896 1.406,4.094 0.615,0.198 10 false CANH 0.802,4.469 1.417,4.667 0.615,0.198 10 false CANL 5.573,4.688 6.854,5.042 1.281,0.354 10 false Power Steering ECU Assembly*4 0.24,4.74 2.26,5.125 2.021,0.385 10 false No. 2 CAN Junction Terminal*2 5.979,5.698 6.594,5.896 0.615,0.198 10 false CANH 6,6.094 6.615,6.292 0.615,0.198 10 false CANL 0.24,5.427 1.656,5.656 1.417,0.229 10 false *1: w/ Airbag System 0.219,6.49 2.427,6.885 2.208,0.396 10 false *4: w/ Variable Flow Control Solenoid Valve 0.26,3.01 2.958,3.396 2.698,0.385 10 false Airbag Sensor Assembly*1 0.229,5.771 1.729,6.01 1.5,0.24 10 false *2: w/o Airbag System 0.229,6.125 2.438,6.521 2.208,0.396 10 false *3: w/o VSC OFF Switch 0.219,7.365 5.813,7.625 5.594,0.26 10 false *6: w/ Tire Pressure Warning System (Tire Inflation Pressure Display Function) 0.208,7.01 2.417,7.406 2.208,0.396 10 false *5: w/ VSC OFF Switch 3,0.552 3.615,0.75 0.615,0.198 10 false N118 3,0.958 3.615,1.156 0.615,0.198 10 false N118 4.073,0.552 4.688,0.75 0.615,0.198 10 false N119 4.073,0.948 4.688,1.146 0.615,0.198 10 false N119 4.073,2.271 4.688,2.469 0.615,0.198 10 false N121 4.073,2.667 4.688,2.865 0.615,0.198 10 false N121 4.073,3.969 4.688,4.167 0.615,0.198 10 false N123 4.073,4.375 4.688,4.573 0.615,0.198 10 false N123 2.99,3.979 3.604,4.177 0.615,0.198 10 false N124 2.99,4.365 3.604,4.563 0.615,0.198 10 false N124 3,2.26 3.615,2.458 0.615,0.198 10 false N120 3,2.667 3.615,2.865 0.615,0.198 10 false N120 4.073,5.688 4.688,5.885 0.615,0.198 10 false N177 4.073,6.083 4.688,6.281 0.615,0.198 10 false N177 5.656,6.281 6.271,6.479 0.615,0.198 10 false Z3 5.563,4.5 6.177,4.698 0.615,0.198 10 false N36 5.198,2.833 5.813,3.031 0.615,0.198 10 false N3 5.51,1.156 6.125,1.354 0.615,0.198 10 false A28 0.24,1.135 0.854,1.333 0.615,0.198 10 false N21 0.229,2.833 0.844,3.031 0.615,0.198 10 false N45 0.156,4.542 0.771,4.74 0.615,0.198 10 false N122 3.125,0.344 3.333,0.521 0.208,0.177 10 false 1 4.177,0.344 4.385,0.521 0.208,0.177 10 false 1 4.188,2.063 4.396,2.24 0.208,0.177 10 false 1 3.115,2.063 3.323,2.24 0.208,0.177 10 false 1 3.115,3.771 3.323,3.948 0.208,0.177 10 false 1 4.177,3.781 4.385,3.958 0.208,0.177 10 false 1 4.177,5.479 4.385,5.656 0.208,0.177 10 false 1 4.188,5.896 4.396,6.073 0.208,0.177 10 false 2 4.188,4.188 4.396,4.365 0.208,0.177 10 false 2 4.198,2.479 4.406,2.656 0.208,0.177 10 false 2 4.188,0.76 4.396,0.938 0.208,0.177 10 false 2 3.125,0.76 3.333,0.938 0.208,0.177 10 false 2 3.125,2.469 3.333,2.646 0.208,0.177 10 false 2 3.115,4.188 3.323,4.365 0.208,0.177 10 false 2 1.365,4.271 1.573,4.448 0.208,0.177 10 false 2 1.365,3.865 1.573,4.042 0.208,0.177 10 false 3 1.354,2.167 1.563,2.344 0.208,0.177 10 false 26 1.354,2.573 1.563,2.75 0.208,0.177 10 false 27 1.375,0.448 1.583,0.625 0.208,0.177 10 false 22 1.385,0.844 1.594,1.021 0.208,0.177 10 false 7 5.688,0.448 5.896,0.625 0.208,0.177 10 false 26 5.688,0.844 5.896,1.021 0.208,0.177 10 false 14 5.771,2.167 5.979,2.344 0.208,0.177 10 false 3 5.771,2.563 5.979,2.74 0.208,0.177 10 false 8 5.771,3.875 5.979,4.052 0.208,0.177 10 false 1 5.781,4.292 5.99,4.469 0.208,0.177 10 false 2 5.76,5.583 5.969,5.76 0.208,0.177 10 false 9 5.708,6.01 5.917,6.188 0.208,0.177 10 false 10

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY

·

When disconnecting and reconnecting the battery.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE


·

Some parts must be initialized and set when replacing or removing and installing parts.

Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM>DIAGNOSIS SYSTEM



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.

·

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRE
NOTICE:

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.


HINT:

Operating the ignition switch, any other switches or door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.


a.

Disconnect the cable from the negative (-) battery terminal.


b.
C368243C53
1.448,0.104 1.917,0.323 0.469,0.219 0.927,1.76 1.135,1.76 1.135,1.76 1.333,1.115 true 0.906,0.521 1.115,0.521 1.115,0.521 1.313,1 true 0.552,1.677 1.01,1.875 0.458,0.198 10 false CA2H 1.573,0.135 2.031,0.333 0.458,0.198 10 false N21 0.531,0.448 0.99,0.646 0.458,0.198 10 false CA2L 0.083,0.063 0.542,0.26 0.458,0.198 10 false *a
*a Component with harness connected
(Central Gateway ECU [Network Gateway ECU])


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N21-22 (CA2H) - N21-7 (CA2L) Cable disconnected from negative (-) battery terminal Below 70 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK FOR SHORT IN CAN BUS WIRES

NG

95.CHECK FOR OPEN IN CAN BUS WIRE (CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU] - NO. 4 CAN JUNCTION CONNECTOR)
2.CHECK FOR SHORT IN CAN BUS WIRES
a.
C368243C53
1.448,0.104 1.917,0.323 0.469,0.219 0.927,1.76 1.135,1.76 1.135,1.76 1.333,1.115 true 0.906,0.521 1.115,0.521 1.115,0.521 1.313,1 true 0.552,1.677 1.01,1.875 0.458,0.198 10 false CA2H 1.573,0.135 2.031,0.333 0.458,0.198 10 false N21 0.531,0.448 0.99,0.646 0.458,0.198 10 false CA2L 0.083,0.063 0.542,0.26 0.458,0.198 10 false *a
*a Component with harness connected
(Central Gateway ECU [Network Gateway ECU])


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N21-22 (CA2H) - N21-7 (CA2L) Cable disconnected from negative (-) battery terminal 54 Ω or higher



Result:
Proceed to
OK
NG



OK

3.CHECK FOR SHORT TO B+ IN CAN BUS WIRE

NG

65.CHECK FOR SHORT IN CAN BUS WIRES (CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU] - NO. 4 CAN JUNCTION CONNECTOR)
3.CHECK FOR SHORT TO B+ IN CAN BUS WIRE
a.
C324419C53
1.448,0.25 1.917,0.51 0.469,0.26 1.427,2.365 1.896,2.625 0.469,0.26 1.333,1.021 1.198,0.427 1.198,0.427 1.031,0.427 true 2.365,3.604 2.031,4.271 2.031,4.271 1.865,4.271 true 1.344,1.135 1.25,1.76 1.25,1.76 1.083,1.76 true 0.063,0.052 0.375,0.25 0.313,0.198 10 false *a 0.115,2.198 0.427,2.396 0.313,0.198 10 false *b 1.552,0.302 2.042,0.552 0.49,0.25 10 false N21 1.531,2.417 2.021,2.667 0.49,0.25 10 false N8 0.646,0.354 1.135,0.604 0.49,0.25 10 false CA2L 1.573,4.188 2.063,4.438 0.49,0.25 10 false BAT 0.74,1.677 1.229,1.927 0.49,0.25 10 false CA2H
*a Component with harness connected
(Central Gateway ECU [Network Gateway ECU])
*b Front view of DLC3


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N21-22 (CA2H) - N8-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
N21-7 (CA2L) - N8-16 (BAT)



Result:
Proceed to
OK
NG



OK

4.CHECK FOR SHORT TO GND IN CAN BUS WIRE

NG

35.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU] - NO. 4 CAN JUNCTION CONNECTOR)
4.CHECK FOR SHORT TO GND IN CAN BUS WIRE
a.
C324419C54
1.448,0.25 1.917,0.51 0.469,0.26 1.427,2.365 1.896,2.625 0.469,0.26 1.333,1.021 1.198,0.427 1.198,0.427 1.031,0.427 true 1.604,3.198 1.333,4.135 1.333,4.135 1.167,4.135 true 1.344,1.135 1.25,1.76 1.25,1.76 1.083,1.76 true 0.063,0.052 0.375,0.25 0.313,0.198 10 false *a 0.115,2.198 0.427,2.396 0.313,0.198 10 false *b 1.552,0.302 2.042,0.552 0.49,0.25 10 false N21 1.531,2.417 2.021,2.667 0.49,0.25 10 false N8 0.646,0.354 1.135,0.604 0.49,0.25 10 false CA2L 0.906,4.052 1.396,4.302 0.49,0.25 10 false CG 0.74,1.677 1.229,1.927 0.49,0.25 10 false CA2H
*a Component with harness connected
(Central Gateway ECU [Network Gateway ECU])
*b Front view of DLC3


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N21-22 (CA2H) - N8-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
N21-7 (CA2L) - N8-4 (CG)



Result:
Proceed to
OK
NG



OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

5.CHECK FOR SHORT TO GND IN CAN BUS WIRE (CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU] - NO. 4 CAN JUNCTION CONNECTOR)
5.CHECK FOR SHORT TO GND IN CAN BUS WIRE (CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU] - NO. 4 CAN JUNCTION CONNECTOR)
a.
C414215C03
1.479,0.26 1.917,0.469 0.438,0.208 1.438,2.542 1.875,2.75 0.438,0.208 2.656,0.646 2.438,0.646 2.438,0.646 2.427,1.26 true 2.146,4.24 1.979,4.24 1.979,4.24 1.646,3.302 true 2.542,2.156 2.323,2.156 2.323,2.156 2.313,1.521 true 1.573,0.292 2.188,0.49 0.615,0.198 10 false N21 1.542,2.573 2.156,2.771 0.615,0.198 10 false N8 0.094,0.073 0.708,0.271 0.615,0.198 10 false *a 0.104,2.563 0.719,2.76 0.615,0.198 10 false *b 2.698,0.573 3.229,0.781 0.531,0.208 10 false CA2L 2.229,4.167 2.844,4.365 0.615,0.198 10 false CG 2.594,2.083 3.125,2.292 0.531,0.208 10 false CA2H
*a Front view of wire harness connector
(to Central Gateway ECU [Network Gateway ECU])
*b Front view of DLC3


Disconnect the N21 central gateway ECU (network gateway ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N21-22 (CA2H) - N8-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
N21-7 (CA2L) - N8-4 (CG)



c.

Reconnect the N21 central gateway ECU (network gateway ECU) connector.


Result:
Proceed to
OK
NG



OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

6.CHECK VEHICLE TYPE
6.CHECK VEHICLE TYPE
a.

Check for vehicle type.


Result:
Result Proceed to
w/ Airbag System A
w/o Airbag System B



A

7.CHECK FOR SHORT TO GND IN CAN BUS WIRE (AIRBAG SENSOR ASSEMBLY - NO. 4 CAN JUNCTION CONNECTOR)

B

8.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 2 CAN JUNCTION TERMINAL - NO. 4 CAN JUNCTION CONNECTOR)
7.CHECK FOR SHORT TO GND IN CAN BUS WIRE (AIRBAG SENSOR ASSEMBLY - NO. 4 CAN JUNCTION CONNECTOR)
a.

Disconnect the N45 airbag sensor assembly connector.

for Type A: Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for Type A)>PRECAUTION

for Type B: Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for Type B)>PRECAUTION

for Type C: Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for Type C)>PRECAUTION

C414200C02
2.083,0.25 2.5,0.5 0.417,0.25 5.198,0.625 5.615,0.875 0.417,0.25 2.531,1.427 2.844,0.448 2.844,0.448 3.01,0.448 true 2.656,1.438 2.948,0.833 2.948,0.833 3.115,0.833 true 5.406,1.323 5.708,2.042 5.708,2.042 5.875,2.042 true 1.135,0.458 1.448,0.656 0.313,0.198 10 false *a 4.656,0.823 4.969,1.021 0.313,0.198 10 false *b 2.167,0.281 2.479,0.479 0.313,0.198 10 false N45 5.323,0.667 5.76,0.896 0.438,0.229 10 false N8 3.104,0.375 3.656,0.604 0.552,0.229 10 false CANH 3.177,0.781 3.729,1.01 0.552,0.229 10 false CANL 5.958,1.969 6.51,2.198 0.552,0.229 10 false CG
*a Front view of wire harness connector
(to Airbag Sensor Assembly)
*b Front view of DLC3



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N45-26 (CANH) - N8-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
N45-27 (CANL) - N8-4 (CG)



c.

Reconnect the N45 airbag sensor assembly connector.


Result:
Proceed to
OK
NG



OK

NG

9.CHECK VEHICLE TYPE
8.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 2 CAN JUNCTION TERMINAL - NO. 4 CAN JUNCTION CONNECTOR)
a.
C414349C01
0.365,0.781 0.854,1.042 0.49,0.26 0.125,2.385 0.615,2.646 0.49,0.26 1.615,2.323 1.875,3.115 1.875,3.115 2.01,3.115 true 1.938,0.885 2.208,0.406 2.208,0.406 2.344,0.406 true 1.292,0.427 1.448,0.427 1.448,0.427 1.729,0.906 true 0.458,0.833 1.073,1.031 0.615,0.198 10 false N122 0.292,2.438 0.906,2.635 0.615,0.198 10 false N8 2.052,3.031 2.365,3.229 0.313,0.198 10 false CG 2.375,0.323 2.99,0.521 0.615,0.198 10 false CANH 0.885,0.344 1.5,0.542 0.615,0.198 10 false CANL 0.135,0.104 0.448,0.302 0.313,0.198 10 false *a 0.135,1.594 0.448,1.792 0.313,0.198 10 false *b
*a Front view of wire harness connector
(to No. 2 CAN Junction Terminal)
*b Front view of DLC3


Disconnect the N122 No. 2 CAN junction terminal connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N122-3 (CANH) - N8-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
N122-2 (CANL) - N8-4 (CG)



c.

Reconnect the N122 No. 2 CAN junction terminal connector.


Result:
Proceed to
OK
NG



OK

REPLACE NO. 2 CAN JUNCTION TERMINAL

NG

17.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 4 CAN JUNCTION CONNECTOR - NO. 2 CAN JUNCTION TERMINAL)
9.CHECK VEHICLE TYPE
a.

Check for vehicle type.


Result:
Result Proceed to
except Wagon A
for Wagon B



A

10.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 4 CAN JUNCTION CONNECTOR - AIRBAG SENSOR ASSEMBLY)

B

23.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 4 CAN JUNCTION CONNECTOR - AIRBAG SENSOR ASSEMBLY)
10.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 4 CAN JUNCTION CONNECTOR - AIRBAG SENSOR ASSEMBLY)
a.

Disconnect the N120 No. 4 CAN junction connector.

HINT:
·

Before disconnecting the connectors, make a note of where it is connected.

·

Reconnect the connector to its original position.



C414491C01
5.823,2.104 6.25,2.354 0.427,0.25 3.927,2.833 4.281,2.573 4.281,2.573 4.448,2.573 true 3.927,2.99 4.26,3.219 4.26,3.219 4.427,3.219 true 5.969,2.875 6.156,3.563 6.156,3.563 6.323,3.563 true 4.479,2.521 5.094,2.719 0.615,0.198 10 false CANH 4.458,3.156 5.073,3.354 0.615,0.198 10 false CANL 1.281,2.438 1.896,2.635 0.615,0.198 10 false N121 1.281,2.198 1.896,2.396 0.615,0.198 10 false N120 2.917,2.198 3.531,2.396 0.615,0.198 10 false *a 0.146,0.083 0.76,0.281 0.615,0.198 10 false *1 1.281,2.688 1.896,2.885 0.615,0.198 10 false N123 1.281,1.948 1.896,2.146 0.615,0.198 10 false N119 1.281,1.667 1.896,1.865 0.615,0.198 10 false N118 5.083,1.875 5.698,2.073 0.615,0.198 10 false *b 5.958,2.167 6.271,2.365 0.313,0.198 10 false N8 6.354,3.479 6.729,3.688 0.375,0.208 10 false CG
*1 No. 4 CAN Junction Connector - -
*a Rear view of wire harness connector
(to No. 4 CAN Junction Connector)
*b Front view of DLC3


Wiring Color
Code Color (CANH Side) Color (CANL Side) Connect to

*1: w/ VSC OFF Switch

*2: w/o VSC OFF Switch

*3: w/ Variable Flow Control Solenoid Valve

N118 SB W Central gateway ECU (network gateway ECU)
N119 GR W Brake actuator assembly (skid control ECU)
N120 R W Airbag sensor assembly
N121 P W
·

Steering sensor*1

·

Combination switch ECU sub-assembly*2


N123 G W Power steering ECU assembly*3


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N120-1 (CANH) - N8-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
N120-2 (CANL) - N8-4 (CG)



c.

Reconnect the N120 No. 4 CAN junction connector.


Result:
Proceed to
OK
NG



OK

11.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 4 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU])

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 4 CAN JUNCTION CONNECTOR - AIRBAG SENSOR ASSEMBLY)

11.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 4 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU])
a.

Disconnect the N118 No. 4 CAN junction connector.

HINT:
·

Before disconnecting the connectors, make a note of where it is connected.

·

Reconnect the connector to its original position.



C414350C01
5.823,2.104 6.25,2.354 0.427,0.25 3.927,2.833 4.281,2.573 4.281,2.573 4.448,2.573 true 3.927,2.99 4.26,3.219 4.26,3.219 4.427,3.219 true 5.969,2.875 6.156,3.563 6.156,3.563 6.323,3.563 true 4.479,2.521 5.094,2.719 0.615,0.198 10 false CANH 4.458,3.156 5.073,3.354 0.615,0.198 10 false CANL 1.281,2.438 1.896,2.635 0.615,0.198 10 false N121 1.281,2.198 1.896,2.396 0.615,0.198 10 false N120 2.917,2.198 3.531,2.396 0.615,0.198 10 false *a 0.146,0.083 0.76,0.281 0.615,0.198 10 false *1 1.281,2.688 1.896,2.885 0.615,0.198 10 false N123*A 1.281,2.927 1.896,3.125 0.615,0.198 10 false N124*A 1.281,1.948 1.896,2.146 0.615,0.198 10 false N119 1.281,1.667 1.896,1.865 0.615,0.198 10 false N118 1.823,2.688 2.438,2.885 0.615,0.198 10 false N124*B 5.083,1.875 5.698,2.073 0.615,0.198 10 false *b 5.958,2.167 6.271,2.365 0.313,0.198 10 false N8 6.354,3.479 6.729,3.688 0.375,0.208 10 false CG
*A for RHD *B for LHD
*1 No. 4 CAN Junction Connector - -
*a Rear view of wire harness connector
(to No. 4 CAN Junction Connector)
*b Front view of DLC3


Wiring Color
Code Color (CANH Side) Color (CANL Side) Connect to

*1: w/ Airbag System

*2: w/ VSC OFF Switch

*3: w/o VSC OFF Switch

*4: w/ Variable Flow Control Solenoid Valve

*5: w/o Airbag System

N118 SB W Central gateway ECU (network gateway ECU)
N119 GR W Brake actuator assembly (skid control ECU)
N120 R W Airbag sensor assembly*1
N121 P W
·

Steering sensor*2

·

Combination switch ECU sub-assembly*3


N123 G W Power steering ECU assembly*4
N124 L W No. 2 CAN junction terminal*5


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N118-1 (CANH) - N8-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
N118-2 (CANL) - N8-4 (CG)



c.

Reconnect the N118 No. 4 CAN junction connector.


Result:
Proceed to
OK
NG



OK

12.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 4 CAN JUNCTION CONNECTOR - BRAKE ACTUATOR ASSEMBLY [SKID CONTROL ECU])

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 4 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU])

12.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 4 CAN JUNCTION CONNECTOR - BRAKE ACTUATOR ASSEMBLY [SKID CONTROL ECU])
a.

Disconnect the N119 No. 4 CAN junction connector.

HINT:
·

Before disconnecting the connectors, make a note of where it is connected.

·

Reconnect the connector to its original position.



C414350C01
5.823,2.104 6.25,2.354 0.427,0.25 3.927,2.833 4.281,2.573 4.281,2.573 4.448,2.573 true 3.927,2.99 4.26,3.219 4.26,3.219 4.427,3.219 true 5.969,2.875 6.156,3.563 6.156,3.563 6.323,3.563 true 4.479,2.521 5.094,2.719 0.615,0.198 10 false CANH 4.458,3.156 5.073,3.354 0.615,0.198 10 false CANL 1.281,2.438 1.896,2.635 0.615,0.198 10 false N121 1.281,2.198 1.896,2.396 0.615,0.198 10 false N120 2.917,2.198 3.531,2.396 0.615,0.198 10 false *a 0.146,0.083 0.76,0.281 0.615,0.198 10 false *1 1.281,2.688 1.896,2.885 0.615,0.198 10 false N123*A 1.281,2.927 1.896,3.125 0.615,0.198 10 false N124*A 1.281,1.948 1.896,2.146 0.615,0.198 10 false N119 1.281,1.667 1.896,1.865 0.615,0.198 10 false N118 1.823,2.688 2.438,2.885 0.615,0.198 10 false N124*B 5.083,1.875 5.698,2.073 0.615,0.198 10 false *b 5.958,2.167 6.271,2.365 0.313,0.198 10 false N8 6.354,3.479 6.729,3.688 0.375,0.208 10 false CG
*A for RHD *B for LHD
*1 No. 4 CAN Junction Connector - -
*a Rear view of wire harness connector
(to No. 4 CAN Junction Connector)
*b Front view of DLC3


Wiring Color
Code Color (CANH Side) Color (CANL Side) Connect to

*1: w/ Airbag System

*2: w/ VSC OFF Switch

*3: w/o VSC OFF Switch

*4: w/ Variable Flow Control Solenoid Valve

*5: w/o Airbag System

N118 SB W Central gateway ECU (network gateway ECU)
N119 GR W Brake actuator assembly (skid control ECU)
N120 R W Airbag sensor assembly*1
N121 P W
·

Steering sensor*2

·

Combination switch ECU sub-assembly*3


N123 G W Power steering ECU assembly*4
N124 L W No. 2 CAN junction terminal*5


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N119-1 (CANH) - N8-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
N119-2 (CANL) - N8-4 (CG)



c.

Reconnect the N119 No. 4 CAN junction connector.


Result:
Proceed to
OK
NG



OK

13.CHECK VEHICLE TYPE

NG

18.CHECK FOR SHORT TO GND IN CAN BUS WIRE (BRAKE ACTUATOR ASSEMBLY [SKID CONTROL ECU] - NO. 4 CAN JUNCTION CONNECTOR)
13.CHECK VEHICLE TYPE
a.

Check for vehicle type.


Result:
Result Proceed to
w/ Variable Flow Control Solenoid Valve A
w/o Variable Flow Control Solenoid Valve B



A

14.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 4 CAN JUNCTION CONNECTOR - POWER STEERING ECU ASSEMBLY)

B

15.CHECK VEHICLE TYPE
14.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 4 CAN JUNCTION CONNECTOR - POWER STEERING ECU ASSEMBLY)
a.

Disconnect the N123 No. 4 CAN junction connector.

HINT:
·

Before disconnecting the connectors, make a note of where it is connected.

·

Reconnect the connector to its original position.



C414492C01
5.823,2.104 6.25,2.354 0.427,0.25 3.927,2.833 4.281,2.573 4.281,2.573 4.448,2.573 true 3.927,2.99 4.26,3.219 4.26,3.219 4.427,3.219 true 5.969,2.875 6.156,3.563 6.156,3.563 6.323,3.563 true 4.479,2.521 5.094,2.719 0.615,0.198 10 false CANH 4.458,3.156 5.073,3.354 0.615,0.198 10 false CANL 1.281,2.438 1.896,2.635 0.615,0.198 10 false N121 1.281,2.198 1.896,2.396 0.615,0.198 10 false N120 2.917,2.198 3.531,2.396 0.615,0.198 10 false *a 0.146,0.083 0.76,0.281 0.615,0.198 10 false *1 1.281,2.688 1.896,2.885 0.615,0.198 10 false N123 1.281,2.927 1.896,3.125 0.615,0.198 10 false N124 1.281,1.948 1.896,2.146 0.615,0.198 10 false N119 1.281,1.667 1.896,1.865 0.615,0.198 10 false N118 5.083,1.875 5.698,2.073 0.615,0.198 10 false *b 5.958,2.167 6.271,2.365 0.313,0.198 10 false N8 6.354,3.479 6.729,3.688 0.375,0.208 10 false CG
*1 No. 4 CAN Junction Connector - -
*a Rear view of wire harness connector
(to No. 4 CAN Junction Connector)
*b Front view of DLC3


Wiring Color
Code Color (CANH Side) Color (CANL Side) Connect to

*1: w/ Airbag System

*2: w/ VSC OFF Switch

*3: w/o VSC OFF Switch

*4: w/o Airbag System

N118 SB W Central gateway ECU (network gateway ECU)
N119 GR W Brake actuator assembly (skid control ECU)
N120 R W Airbag sensor assembly*1
N121 P W
·

Steering sensor*2

·

Combination switch ECU sub-assembly*3


N123 G W Power steering ECU assembly
N124 L W No. 2 CAN junction terminal*4


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N123-1 (CANH) - N8-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
N123-2 (CANL) - N8-4 (CG)



c.

Reconnect the N123 No. 4 CAN junction connector.


Result:
Proceed to
OK
NG



OK

15.CHECK VEHICLE TYPE

NG

19.CHECK FOR SHORT TO GND IN CAN BUS WIRE (POWER STEERING ECU ASSEMBLY - NO. 4 CAN JUNCTION CONNECTOR)
15.CHECK VEHICLE TYPE
a.

Check for vehicle type.


Result:
Result Proceed to
w/ VSC OFF Switch A
w/o VSC OFF Switch B



A

16.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 4 CAN JUNCTION CONNECTOR - STEERING SENSOR)

B

20.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 4 CAN JUNCTION CONNECTOR - COMBINATION SWITCH ECU SUB-ASSEMBLY)
16.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 4 CAN JUNCTION CONNECTOR - STEERING SENSOR)
a.

Disconnect the N121 No. 4 CAN junction connector.

HINT:
·

Before disconnecting the connectors, make a note of where it is connected.

·

Reconnect the connector to its original position.



C414350C01
5.823,2.104 6.25,2.354 0.427,0.25 3.927,2.833 4.281,2.573 4.281,2.573 4.448,2.573 true 3.927,2.99 4.26,3.219 4.26,3.219 4.427,3.219 true 5.969,2.875 6.156,3.563 6.156,3.563 6.323,3.563 true 4.479,2.521 5.094,2.719 0.615,0.198 10 false CANH 4.458,3.156 5.073,3.354 0.615,0.198 10 false CANL 1.281,2.438 1.896,2.635 0.615,0.198 10 false N121 1.281,2.198 1.896,2.396 0.615,0.198 10 false N120 2.917,2.198 3.531,2.396 0.615,0.198 10 false *a 0.146,0.083 0.76,0.281 0.615,0.198 10 false *1 1.281,2.688 1.896,2.885 0.615,0.198 10 false N123*A 1.281,2.927 1.896,3.125 0.615,0.198 10 false N124*A 1.281,1.948 1.896,2.146 0.615,0.198 10 false N119 1.281,1.667 1.896,1.865 0.615,0.198 10 false N118 1.823,2.688 2.438,2.885 0.615,0.198 10 false N124*B 5.083,1.875 5.698,2.073 0.615,0.198 10 false *b 5.958,2.167 6.271,2.365 0.313,0.198 10 false N8 6.354,3.479 6.729,3.688 0.375,0.208 10 false CG
*A for RHD *B for LHD
*1 No. 4 CAN Junction Connector - -
*a Rear view of wire harness connector
(to No. 4 CAN Junction Connector)
*b Front view of DLC3


Wiring Color
Code Color (CANH Side) Color (CANL Side) Connect to

*1: w/ Airbag System

*2: w/ Variable Flow Control Solenoid Valve

*3: w/o Airbag System

N118 SB W Central gateway ECU (network gateway ECU)
N119 GR W Brake actuator assembly (skid control ECU)
N120 R W Airbag sensor assembly*1
N121 P W Steering sensor
N123 G W Power steering ECU assembly*2
N124 L W No. 2 CAN junction terminal*3


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N121-1 (CANH) - N8-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
N121-2 (CANL) - N8-4 (CG)



c.

Reconnect the N121 No. 4 CAN junction connector.


Result:
Proceed to
OK
NG



OK

REPLACE NO. 4 CAN JUNCTION CONNECTOR

NG

21.CHECK FOR SHORT TO GND IN CAN BUS WIRE (STEERING SENSOR - NO. 4 CAN JUNCTION CONNECTOR)
17.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 4 CAN JUNCTION CONNECTOR - NO. 2 CAN JUNCTION TERMINAL)
a.

Disconnect the N124 No. 4 CAN junction connector.

HINT:
·

Before disconnecting the connectors, make a note of where it is connected.

·

Reconnect the connector to its original position.



C414490C01
5.823,2.104 6.25,2.354 0.427,0.25 3.927,2.833 4.281,2.573 4.281,2.573 4.448,2.573 true 3.927,2.99 4.26,3.219 4.26,3.219 4.427,3.219 true 5.969,2.875 6.156,3.563 6.156,3.563 6.323,3.563 true 4.479,2.521 5.094,2.719 0.615,0.198 10 false CANH 4.458,3.156 5.073,3.354 0.615,0.198 10 false CANL 1.281,2.438 1.896,2.635 0.615,0.198 10 false N121 2.917,2.198 3.531,2.396 0.615,0.198 10 false *a 0.146,0.083 0.76,0.281 0.615,0.198 10 false *1 1.281,2.688 1.896,2.885 0.615,0.198 10 false N123*A 1.281,2.927 1.896,3.125 0.615,0.198 10 false N124*A 1.281,1.948 1.896,2.146 0.615,0.198 10 false N119 1.281,1.667 1.896,1.865 0.615,0.198 10 false N118 1.823,2.688 2.438,2.885 0.615,0.198 10 false N124*B 5.083,1.875 5.698,2.073 0.615,0.198 10 false *b 5.958,2.167 6.271,2.365 0.313,0.198 10 false N8 6.354,3.479 6.729,3.688 0.375,0.208 10 false CG
*A for RHD *B for LHD
*1 No. 4 CAN Junction Connector - -
*a Rear view of wire harness connector
(to No. 4 CAN Junction Connector)
*b Front view of DLC3


Wiring Color
Code Color (CANH Side) Color (CANL Side) Connect to

*1: w/ VSC OFF Switch

*2: w/o VSC OFF Switch

*3: w/ Variable Flow Control Solenoid Valve

N118 SB W Central gateway ECU (network gateway ECU)
N119 GR W Brake actuator assembly (skid control ECU)
N121 P W
·

Steering sensor*1

·

Combination switch ECU sub-assembly*2


N123 G W Power steering ECU assembly*3
N124 L W No. 2 CAN junction terminal


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N124-1 (CANH) - N8-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
N124-2 (CANL) - N8-4 (CG)



c.

Reconnect the N124 No. 4 CAN junction connector.


Result:
Proceed to
OK
NG



OK

11.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 4 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU])

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 4 CAN JUNCTION CONNECTOR - NO. 2 CAN JUNCTION TERMINAL)

18.CHECK FOR SHORT TO GND IN CAN BUS WIRE (BRAKE ACTUATOR ASSEMBLY [SKID CONTROL ECU] - NO. 4 CAN JUNCTION CONNECTOR)
a.
C414351C01
1.479,0.313 1.927,0.573 0.448,0.26 1.479,2.677 1.927,2.938 0.448,0.26 1.99,4.354 1.854,4.354 1.854,4.354 1.625,3.573 true 1.313,2.198 1.177,2.198 1.177,2.198 0.99,1.583 true 1.229,0.823 1.094,0.823 1.094,0.823 0.896,1.281 true 0.094,0.073 0.427,0.396 0.333,0.323 10 false *a 0.094,2.594 0.5,2.938 0.406,0.344 10 false *b 1.583,0.365 2.042,0.563 0.458,0.198 10 false A28 1.625,2.74 2.083,2.938 0.458,0.198 10 false N8 2.031,4.26 2.344,4.458 0.313,0.198 10 false CG 1.354,2.115 1.969,2.313 0.615,0.198 10 false CANL 1.26,0.729 1.875,0.927 0.615,0.198 10 false CANH
*a Front view of wire harness connector
(to Brake Actuator Assembly [Skid Control ECU])
*b Front view of DLC3


Disconnect the A28 brake actuator assembly (skid control ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A28-26 (CANH) - N8-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
A28-14 (CANL) - N8-4 (CG)



c.

Reconnect the A28 brake actuator assembly (skid control ECU) connector.


Result:
Proceed to
OK
NG



OK

REPLACE BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU)

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (BRAKE ACTUATOR ASSEMBLY [SKID CONTROL ECU] - NO. 4 CAN JUNCTION CONNECTOR)

19.CHECK FOR SHORT TO GND IN CAN BUS WIRE (POWER STEERING ECU ASSEMBLY - NO. 4 CAN JUNCTION CONNECTOR)
a.
C379614C05
0.24,0.99 0.594,1.188 0.354,0.198 0.167,2.333 0.521,2.531 0.354,0.198 0.833,1.792 1.021,1.792 1.021,1.792 1.125,1.271 true 1.542,0.333 1.375,0.333 1.375,0.333 1.302,1.135 true 2.146,3.146 1.979,3.146 1.979,3.146 1.667,2.375 true 0.354,0.135 0.667,0.333 0.313,0.198 10 false *a 0.427,1.729 0.938,1.938 0.51,0.208 10 false CANH 1.583,0.26 2.094,0.469 0.51,0.208 10 false CANL 0.292,1.01 0.802,1.219 0.51,0.208 10 false N36 0.24,2.354 0.75,2.563 0.51,0.208 10 false N8 2.219,3.083 2.729,3.292 0.51,0.208 10 false CG 0.25,2.01 0.563,2.208 0.313,0.198 10 false *b
*a Front view of wire harness connector
(to Power Steering ECU Assembly)
*b Front view of DLC3


Disconnect the N36 power steering ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N36-1 (CANH) - N8-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
N36-2 (CANL) - N8-4 (CG)



c.

Reconnect the N36 power steering ECU assembly connector.


Result:
Proceed to
OK
NG



OK

REPLACE POWER STEERING ECU ASSEMBLY

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (POWER STEERING ECU ASSEMBLY - NO. 4 CAN JUNCTION CONNECTOR)

20.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 4 CAN JUNCTION CONNECTOR - COMBINATION SWITCH ECU SUB-ASSEMBLY)
a.

Disconnect the N121 No. 4 CAN junction connector.

HINT:
·

Before disconnecting the connectors, make a note of where it is connected.

·

Reconnect the connector to its original position.



C414350C01
5.823,2.104 6.25,2.354 0.427,0.25 3.927,2.833 4.281,2.573 4.281,2.573 4.448,2.573 true 3.927,2.99 4.26,3.219 4.26,3.219 4.427,3.219 true 5.969,2.875 6.156,3.563 6.156,3.563 6.323,3.563 true 4.479,2.521 5.094,2.719 0.615,0.198 10 false CANH 4.458,3.156 5.073,3.354 0.615,0.198 10 false CANL 1.281,2.438 1.896,2.635 0.615,0.198 10 false N121 1.281,2.198 1.896,2.396 0.615,0.198 10 false N120 2.917,2.198 3.531,2.396 0.615,0.198 10 false *a 0.146,0.083 0.76,0.281 0.615,0.198 10 false *1 1.281,2.688 1.896,2.885 0.615,0.198 10 false N123*A 1.281,2.927 1.896,3.125 0.615,0.198 10 false N124*A 1.281,1.948 1.896,2.146 0.615,0.198 10 false N119 1.281,1.667 1.896,1.865 0.615,0.198 10 false N118 1.823,2.688 2.438,2.885 0.615,0.198 10 false N124*B 5.083,1.875 5.698,2.073 0.615,0.198 10 false *b 5.958,2.167 6.271,2.365 0.313,0.198 10 false N8 6.354,3.479 6.729,3.688 0.375,0.208 10 false CG
*A for RHD *B for LHD
*1 No. 4 CAN Junction Connector - -
*a Rear view of wire harness connector
(to No. 4 CAN Junction Connector)
*b Front view of DLC3


Wiring Color
Code Color (CANH Side) Color (CANL Side) Connect to

*1: w/ Airbag System

*2: w/ Variable Flow Control Solenoid Valve

*3: w/o Airbag System

N118 SB W Central gateway ECU (network gateway ECU)
N119 GR W Brake actuator assembly (skid control ECU)
N120 R W Airbag sensor assembly*1
N121 P W Combination switch ECU sub-assembly
N123 G W Power steering ECU assembly*2
N124 L W No. 2 CAN junction terminal*3


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N121-1 (CANH) - N8-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
N121-2 (CANL) - N8-4 (CG)



c.

Reconnect the N121 No. 4 CAN junction connector.


Result:
Proceed to
OK
NG



OK

REPLACE NO. 4 CAN JUNCTION CONNECTOR

NG

22.CHECK FOR SHORT TO GND IN CAN BUS WIRE (COMBINATION SWITCH ECU SUB-ASSEMBLY - NO. 4 CAN JUNCTION CONNECTOR)
21.CHECK FOR SHORT TO GND IN CAN BUS WIRE (STEERING SENSOR - NO. 4 CAN JUNCTION CONNECTOR)
a.
C414352C01
0.427,0.865 0.865,1.104 0.438,0.24 0.188,2.542 0.625,2.781 0.438,0.24 1.625,2.458 1.854,3.24 1.854,3.24 1.979,3.24 true 1.719,1.271 1.833,1.75 1.833,1.75 1.958,1.75 true 1.708,0.948 1.833,0.229 1.833,0.229 1.958,0.229 true 0.573,0.906 0.875,1.104 0.302,0.198 10 false N3 1.99,0.146 2.448,0.344 0.458,0.198 10 false CANH 2,1.667 2.458,1.865 0.458,0.198 10 false CANL 2.01,3.156 2.469,3.354 0.458,0.198 10 false CG 0.323,2.583 0.625,2.781 0.302,0.198 10 false N8 0.146,0.104 0.458,0.302 0.313,0.198 10 false *a 0.146,1.823 0.698,2.115 0.552,0.292 10 false *b
*a Front view of wire harness connector
(to Steering Sensor)
*b Front view of DLC3


Disconnect the N3 steering sensor connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N3-3 (CANH) - N8-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
N3-8 (CANL) - N8-4 (CG)



c.

Reconnect the N3 steering sensor connector.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (STEERING SENSOR - NO. 4 CAN JUNCTION CONNECTOR)

22.CHECK FOR SHORT TO GND IN CAN BUS WIRE (COMBINATION SWITCH ECU SUB-ASSEMBLY - NO. 4 CAN JUNCTION CONNECTOR)
a.
C414352C01
0.427,0.865 0.865,1.104 0.438,0.24 0.188,2.542 0.625,2.781 0.438,0.24 1.625,2.458 1.854,3.24 1.854,3.24 1.979,3.24 true 1.719,1.271 1.833,1.75 1.833,1.75 1.958,1.75 true 1.708,0.948 1.833,0.229 1.833,0.229 1.958,0.229 true 0.573,0.906 0.875,1.104 0.302,0.198 10 false N3 1.99,0.146 2.448,0.344 0.458,0.198 10 false CANH 2,1.667 2.458,1.865 0.458,0.198 10 false CANL 2.01,3.156 2.469,3.354 0.458,0.198 10 false CG 0.323,2.583 0.625,2.781 0.302,0.198 10 false N8 0.146,0.104 0.458,0.302 0.313,0.198 10 false *a 0.146,1.823 0.698,2.115 0.552,0.292 10 false *b
*a Front view of wire harness connector
(to Combination Switch ECU Sub-assembly)
*b Front view of DLC3


Disconnect the N3 combination switch ECU sub-assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N3-3 (CANH) - N8-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
N3-8 (CANL) - N8-4 (CG)



c.

Reconnect the N3 combination switch ECU sub-assembly connector.


Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION SWITCH ECU SUB-ASSEMBLY

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (COMBINATION SWITCH ECU SUB-ASSEMBLY - NO. 4 CAN JUNCTION CONNECTOR)

23.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 4 CAN JUNCTION CONNECTOR - AIRBAG SENSOR ASSEMBLY)
a.

Disconnect the N120 No. 4 CAN junction connector.

HINT:
·

Before disconnecting the connectors, make a note of where it is connected.

·

Reconnect the connector to its original position.



C414819C02
5.823,2.104 6.25,2.354 0.427,0.25 3.927,2.833 4.281,2.573 4.281,2.573 4.448,2.573 true 3.927,2.99 4.26,3.219 4.26,3.219 4.427,3.219 true 5.969,2.875 6.156,3.563 6.156,3.563 6.323,3.563 true 4.479,2.521 5.094,2.719 0.615,0.198 10 false CANH 4.458,3.156 5.073,3.354 0.615,0.198 10 false CANL 1.281,2.417 1.896,2.615 0.615,0.198 10 false N121*B 1.281,2.167 1.896,2.365 0.615,0.198 10 false N120*B 2.917,2.198 3.531,2.396 0.615,0.198 10 false *a 0.146,0.083 0.76,0.281 0.615,0.198 10 false *1 1.271,2.656 1.885,2.854 0.615,0.198 10 false N177*B 1.271,2.885 1.885,3.083 0.615,0.198 10 false N120*A 1.26,1.917 1.875,2.115 0.615,0.198 10 false N119*B 1.271,1.667 1.885,1.865 0.615,0.198 10 false N118*B 1.813,2.646 2.427,2.844 0.615,0.198 10 false N121*A 5.083,1.875 5.698,2.073 0.615,0.198 10 false *b 5.958,2.167 6.271,2.365 0.313,0.198 10 false N8 6.354,3.479 6.729,3.688 0.375,0.208 10 false CG 1.271,3.135 1.885,3.333 0.615,0.198 10 false N119*A 1.271,3.385 1.885,3.583 0.615,0.198 10 false N118*A 1.802,2.396 2.417,2.594 0.615,0.198 10 false N123*A 1.802,2.156 2.417,2.354 0.615,0.198 10 false N177*A
*A for RHD *B for LHD
*1 No. 4 CAN Junction Connector - -
*a Rear view of wire harness connector
(to No. 4 CAN Junction Connector)
*b Front view of DLC3


Wiring Color
Code Color (CANH Side) Color (CANL Side) Connect to

*1: w/ Variable Flow Control Solenoid Valve

*2: w/ Tire Pressure Warning System (Tire Inflation Pressure Display Function)

N118 SB W Central gateway ECU (network gateway ECU)
N119 GR W Brake actuator assembly (skid control ECU)
N120 R W Airbag sensor assembly
N121 P W Steering sensor
N123 G W Power steering ECU assembly*1
N177 B W Tire pressure warning ECU and receiver*2


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N120-1 (CANH) - N8-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
N120-2 (CANL) - N8-4 (CG)



c.

Reconnect the N120 No. 4 CAN junction connector.


Result:
Proceed to
OK
NG



OK

24.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 4 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU])

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 4 CAN JUNCTION CONNECTOR - AIRBAG SENSOR ASSEMBLY)

24.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 4 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU])
a.

Disconnect the N118 No. 4 CAN junction connector.

HINT:
·

Before disconnecting the connectors, make a note of where it is connected.

·

Reconnect the connector to its original position.



C414819C02
5.823,2.104 6.25,2.354 0.427,0.25 3.927,2.833 4.281,2.573 4.281,2.573 4.448,2.573 true 3.927,2.99 4.26,3.219 4.26,3.219 4.427,3.219 true 5.969,2.875 6.156,3.563 6.156,3.563 6.323,3.563 true 4.479,2.521 5.094,2.719 0.615,0.198 10 false CANH 4.458,3.156 5.073,3.354 0.615,0.198 10 false CANL 1.281,2.417 1.896,2.615 0.615,0.198 10 false N121*B 1.281,2.167 1.896,2.365 0.615,0.198 10 false N120*B 2.917,2.198 3.531,2.396 0.615,0.198 10 false *a 0.146,0.083 0.76,0.281 0.615,0.198 10 false *1 1.271,2.656 1.885,2.854 0.615,0.198 10 false N177*B 1.271,2.885 1.885,3.083 0.615,0.198 10 false N120*A 1.26,1.917 1.875,2.115 0.615,0.198 10 false N119*B 1.271,1.667 1.885,1.865 0.615,0.198 10 false N118*B 1.813,2.646 2.427,2.844 0.615,0.198 10 false N121*A 5.083,1.875 5.698,2.073 0.615,0.198 10 false *b 5.958,2.167 6.271,2.365 0.313,0.198 10 false N8 6.354,3.479 6.729,3.688 0.375,0.208 10 false CG 1.271,3.135 1.885,3.333 0.615,0.198 10 false N119*A 1.271,3.385 1.885,3.583 0.615,0.198 10 false N118*A 1.802,2.396 2.417,2.594 0.615,0.198 10 false N123*A 1.802,2.156 2.417,2.354 0.615,0.198 10 false N177*A
*A for RHD *B for LHD
*1 No. 4 CAN Junction Connector - -
*a Rear view of wire harness connector
(to No. 4 CAN Junction Connector)
*b Front view of DLC3


Wiring Color
Code Color (CANH Side) Color (CANL Side) Connect to

*1: w/ Variable Flow Control Solenoid Valve

*2: w/ Tire Pressure Warning System (Tire Inflation Pressure Display Function)

N118 SB W Central gateway ECU (network gateway ECU)
N119 GR W Brake actuator assembly (skid control ECU)
N120 R W Airbag sensor assembly
N121 P W Steering sensor
N123 G W Power steering ECU assembly*1
N177 B W Tire pressure warning ECU and receiver*2


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N118-1 (CANH) - N8-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
N118-2 (CANL) - N8-4 (CG)



c.

Reconnect the N118 No. 4 CAN junction connector.


Result:
Proceed to
OK
NG



OK

25.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 4 CAN JUNCTION CONNECTOR - BRAKE ACTUATOR ASSEMBLY [SKID CONTROL ECU])

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 4 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU])

25.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 4 CAN JUNCTION CONNECTOR - BRAKE ACTUATOR ASSEMBLY [SKID CONTROL ECU])
a.

Disconnect the N119 No. 4 CAN junction connector.

HINT:
·

Before disconnecting the connectors, make a note of where it is connected.

·

Reconnect the connector to its original position.



C414819C02
5.823,2.104 6.25,2.354 0.427,0.25 3.927,2.833 4.281,2.573 4.281,2.573 4.448,2.573 true 3.927,2.99 4.26,3.219 4.26,3.219 4.427,3.219 true 5.969,2.875 6.156,3.563 6.156,3.563 6.323,3.563 true 4.479,2.521 5.094,2.719 0.615,0.198 10 false CANH 4.458,3.156 5.073,3.354 0.615,0.198 10 false CANL 1.281,2.417 1.896,2.615 0.615,0.198 10 false N121*B 1.281,2.167 1.896,2.365 0.615,0.198 10 false N120*B 2.917,2.198 3.531,2.396 0.615,0.198 10 false *a 0.146,0.083 0.76,0.281 0.615,0.198 10 false *1 1.271,2.656 1.885,2.854 0.615,0.198 10 false N177*B 1.271,2.885 1.885,3.083 0.615,0.198 10 false N120*A 1.26,1.917 1.875,2.115 0.615,0.198 10 false N119*B 1.271,1.667 1.885,1.865 0.615,0.198 10 false N118*B 1.813,2.646 2.427,2.844 0.615,0.198 10 false N121*A 5.083,1.875 5.698,2.073 0.615,0.198 10 false *b 5.958,2.167 6.271,2.365 0.313,0.198 10 false N8 6.354,3.479 6.729,3.688 0.375,0.208 10 false CG 1.271,3.135 1.885,3.333 0.615,0.198 10 false N119*A 1.271,3.385 1.885,3.583 0.615,0.198 10 false N118*A 1.802,2.396 2.417,2.594 0.615,0.198 10 false N123*A 1.802,2.156 2.417,2.354 0.615,0.198 10 false N177*A
*A for RHD *B for LHD
*1 No. 4 CAN Junction Connector - -
*a Rear view of wire harness connector
(to No. 4 CAN Junction Connector)
*b Front view of DLC3


Wiring Color
Code Color (CANH Side) Color (CANL Side) Connect to

*1: w/ Variable Flow Control Solenoid Valve

*2: w/ Tire Pressure Warning System (Tire Inflation Pressure Display Function)

N118 SB W Central gateway ECU (network gateway ECU)
N119 GR W Brake actuator assembly (skid control ECU)
N120 R W Airbag sensor assembly
N121 P W Steering sensor
N123 G W Power steering ECU assembly*1
N177 B W Tire pressure warning ECU and receiver*2


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N119-1 (CANH) - N8-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
N119-2 (CANL) - N8-4 (CG)



c.

Reconnect the N119 No. 4 CAN junction connector.


Result:
Proceed to
OK
NG



OK

26.CHECK VEHICLE TYPE

NG

30.CHECK FOR SHORT TO GND IN CAN BUS WIRE (BRAKE ACTUATOR ASSEMBLY [SKID CONTROL ECU] - NO. 4 CAN JUNCTION CONNECTOR)
26.CHECK VEHICLE TYPE
a.

Check for vehicle type.


Result:
Result Proceed to
w/ Variable Flow Control Solenoid Valve A
w/o Variable Flow Control Solenoid Valve B



A

27.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 4 CAN JUNCTION CONNECTOR - POWER STEERING ECU ASSEMBLY)

B

28.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 4 CAN JUNCTION CONNECTOR - STEERING SENSOR)
27.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 4 CAN JUNCTION CONNECTOR - POWER STEERING ECU ASSEMBLY)
a.

Disconnect the N123 No. 4 CAN junction connector.

HINT:
·

Before disconnecting the connectors, make a note of where it is connected.

·

Reconnect the connector to its original position.



C414819C02
5.823,2.104 6.25,2.354 0.427,0.25 3.927,2.833 4.281,2.573 4.281,2.573 4.448,2.573 true 3.927,2.99 4.26,3.219 4.26,3.219 4.427,3.219 true 5.969,2.875 6.156,3.563 6.156,3.563 6.323,3.563 true 4.479,2.521 5.094,2.719 0.615,0.198 10 false CANH 4.458,3.156 5.073,3.354 0.615,0.198 10 false CANL 1.281,2.417 1.896,2.615 0.615,0.198 10 false N121*B 1.281,2.167 1.896,2.365 0.615,0.198 10 false N120*B 2.917,2.198 3.531,2.396 0.615,0.198 10 false *a 0.146,0.083 0.76,0.281 0.615,0.198 10 false *1 1.271,2.656 1.885,2.854 0.615,0.198 10 false N177*B 1.271,2.885 1.885,3.083 0.615,0.198 10 false N120*A 1.26,1.917 1.875,2.115 0.615,0.198 10 false N119*B 1.271,1.667 1.885,1.865 0.615,0.198 10 false N118*B 1.813,2.646 2.427,2.844 0.615,0.198 10 false N121*A 5.083,1.875 5.698,2.073 0.615,0.198 10 false *b 5.958,2.167 6.271,2.365 0.313,0.198 10 false N8 6.354,3.479 6.729,3.688 0.375,0.208 10 false CG 1.271,3.135 1.885,3.333 0.615,0.198 10 false N119*A 1.271,3.385 1.885,3.583 0.615,0.198 10 false N118*A 1.802,2.396 2.417,2.594 0.615,0.198 10 false N123*A 1.802,2.156 2.417,2.354 0.615,0.198 10 false N177*A
*A for RHD *B for LHD
*1 No. 4 CAN Junction Connector - -
*a Rear view of wire harness connector
(to No. 4 CAN Junction Connector)
*b Front view of DLC3


Wiring Color
Code Color (CANH Side) Color (CANL Side) Connect to

*1: w/ Variable Flow Control Solenoid Valve

*2: w/ Tire Pressure Warning System (Tire Inflation Pressure Display Function)

N118 SB W Central gateway ECU (network gateway ECU)
N119 GR W Brake actuator assembly (skid control ECU)
N120 R W Airbag sensor assembly
N121 P W Steering sensor
N123 G W Power steering ECU assembly*1
N177 B W Tire pressure warning ECU and receiver*2


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N123-1 (CANH) - N8-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
N123-2 (CANL) - N8-4 (CG)



c.

Reconnect the N123 No. 4 CAN junction connector.


Result:
Proceed to
OK
NG



OK

28.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 4 CAN JUNCTION CONNECTOR - STEERING SENSOR)

NG

31.CHECK FOR SHORT TO GND IN CAN BUS WIRE (POWER STEERING ECU ASSEMBLY - NO. 4 CAN JUNCTION CONNECTOR)
28.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 4 CAN JUNCTION CONNECTOR - STEERING SENSOR)
a.

Disconnect the N121 No. 4 CAN junction connector.

HINT:
·

Before disconnecting the connectors, make a note of where it is connected.

·

Reconnect the connector to its original position.



C414819C02
5.823,2.104 6.25,2.354 0.427,0.25 3.927,2.833 4.281,2.573 4.281,2.573 4.448,2.573 true 3.927,2.99 4.26,3.219 4.26,3.219 4.427,3.219 true 5.969,2.875 6.156,3.563 6.156,3.563 6.323,3.563 true 4.479,2.521 5.094,2.719 0.615,0.198 10 false CANH 4.458,3.156 5.073,3.354 0.615,0.198 10 false CANL 1.281,2.417 1.896,2.615 0.615,0.198 10 false N121*B 1.281,2.167 1.896,2.365 0.615,0.198 10 false N120*B 2.917,2.198 3.531,2.396 0.615,0.198 10 false *a 0.146,0.083 0.76,0.281 0.615,0.198 10 false *1 1.271,2.656 1.885,2.854 0.615,0.198 10 false N177*B 1.271,2.885 1.885,3.083 0.615,0.198 10 false N120*A 1.26,1.917 1.875,2.115 0.615,0.198 10 false N119*B 1.271,1.667 1.885,1.865 0.615,0.198 10 false N118*B 1.813,2.646 2.427,2.844 0.615,0.198 10 false N121*A 5.083,1.875 5.698,2.073 0.615,0.198 10 false *b 5.958,2.167 6.271,2.365 0.313,0.198 10 false N8 6.354,3.479 6.729,3.688 0.375,0.208 10 false CG 1.271,3.135 1.885,3.333 0.615,0.198 10 false N119*A 1.271,3.385 1.885,3.583 0.615,0.198 10 false N118*A 1.802,2.396 2.417,2.594 0.615,0.198 10 false N123*A 1.802,2.156 2.417,2.354 0.615,0.198 10 false N177*A
*A for RHD *B for LHD
*1 No. 4 CAN Junction Connector - -
*a Rear view of wire harness connector
(to No. 4 CAN Junction Connector)
*b Front view of DLC3


Wiring Color
Code Color (CANH Side) Color (CANL Side) Connect to

*1: w/ Variable Flow Control Solenoid Valve

*2: w/ Tire Pressure Warning System (Tire Inflation Pressure Display Function)

N118 SB W Central gateway ECU (network gateway ECU)
N119 GR W Brake actuator assembly (skid control ECU)
N120 R W Airbag sensor assembly
N121 P W Steering sensor
N123 G W Power steering ECU assembly*1
N177 B W Tire pressure warning ECU and receiver*2


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N121-1 (CANH) - N8-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
N121-2 (CANL) - N8-4 (CG)



c.

Reconnect the N121 No. 4 CAN junction connector.


Result:
Proceed to
OK
NG



OK

29.CHECK VEHICLE TYPE

NG

32.CHECK FOR SHORT TO GND IN CAN BUS WIRE (STEERING SENSOR - NO. 4 CAN JUNCTION CONNECTOR)
29.CHECK VEHICLE TYPE
a.

Check for vehicle type.


Result:
Result Proceed to
w/o Tire Pressure Warning System (Tire Inflation Pressure Display Function) A
w/ Tire Pressure Warning System (Tire Inflation Pressure Display Function) B



A

REPLACE NO. 4 CAN JUNCTION CONNECTOR

B

33.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 4 CAN JUNCTION CONNECTOR - TIRE PRESSURE WARNING ECU AND RECEIVER)
30.CHECK FOR SHORT TO GND IN CAN BUS WIRE (BRAKE ACTUATOR ASSEMBLY [SKID CONTROL ECU] - NO. 4 CAN JUNCTION CONNECTOR)
a.
C414351C01
1.479,0.313 1.927,0.573 0.448,0.26 1.479,2.677 1.927,2.938 0.448,0.26 1.99,4.354 1.854,4.354 1.854,4.354 1.625,3.573 true 1.313,2.198 1.177,2.198 1.177,2.198 0.99,1.583 true 1.229,0.823 1.094,0.823 1.094,0.823 0.896,1.281 true 0.094,0.073 0.427,0.396 0.333,0.323 10 false *a 0.094,2.594 0.5,2.938 0.406,0.344 10 false *b 1.583,0.365 2.042,0.563 0.458,0.198 10 false A28 1.625,2.74 2.083,2.938 0.458,0.198 10 false N8 2.031,4.26 2.344,4.458 0.313,0.198 10 false CG 1.354,2.115 1.969,2.313 0.615,0.198 10 false CANL 1.26,0.729 1.875,0.927 0.615,0.198 10 false CANH
*a Front view of wire harness connector
(to Brake Actuator Assembly [Skid Control ECU])
*b Front view of DLC3


Disconnect the A28 brake actuator assembly (skid control ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A28-26 (CANH) - N8-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
A28-14 (CANL) - N8-4 (CG)



c.

Reconnect the A28 brake actuator assembly (skid control ECU) connector.


Result:
Proceed to
OK
NG



OK

REPLACE BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU)

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (BRAKE ACTUATOR ASSEMBLY [SKID CONTROL ECU] - NO. 4 CAN JUNCTION CONNECTOR)

31.CHECK FOR SHORT TO GND IN CAN BUS WIRE (POWER STEERING ECU ASSEMBLY - NO. 4 CAN JUNCTION CONNECTOR)
a.
C379614C05
0.24,0.99 0.594,1.188 0.354,0.198 0.167,2.333 0.521,2.531 0.354,0.198 0.833,1.792 1.021,1.792 1.021,1.792 1.125,1.271 true 1.542,0.333 1.375,0.333 1.375,0.333 1.302,1.135 true 2.146,3.146 1.979,3.146 1.979,3.146 1.667,2.375 true 0.354,0.135 0.667,0.333 0.313,0.198 10 false *a 0.427,1.729 0.938,1.938 0.51,0.208 10 false CANH 1.583,0.26 2.094,0.469 0.51,0.208 10 false CANL 0.292,1.01 0.802,1.219 0.51,0.208 10 false N36 0.24,2.354 0.75,2.563 0.51,0.208 10 false N8 2.219,3.083 2.729,3.292 0.51,0.208 10 false CG 0.25,2.01 0.563,2.208 0.313,0.198 10 false *b
*a Front view of wire harness connector
(to Power Steering ECU Assembly)
*b Front view of DLC3


Disconnect the N36 power steering ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N36-1 (CANH) - N8-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
N36-2 (CANL) - N8-4 (CG)



c.

Reconnect the N36 power steering ECU assembly connector.


Result:
Proceed to
OK
NG



OK

REPLACE POWER STEERING ECU ASSEMBLY

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (POWER STEERING ECU ASSEMBLY - NO. 4 CAN JUNCTION CONNECTOR)

32.CHECK FOR SHORT TO GND IN CAN BUS WIRE (STEERING SENSOR - NO. 4 CAN JUNCTION CONNECTOR)
a.
C414352C01
0.427,0.865 0.865,1.104 0.438,0.24 0.188,2.542 0.625,2.781 0.438,0.24 1.625,2.458 1.854,3.24 1.854,3.24 1.979,3.24 true 1.719,1.271 1.833,1.75 1.833,1.75 1.958,1.75 true 1.708,0.948 1.833,0.229 1.833,0.229 1.958,0.229 true 0.573,0.906 0.875,1.104 0.302,0.198 10 false N3 1.99,0.146 2.448,0.344 0.458,0.198 10 false CANH 2,1.667 2.458,1.865 0.458,0.198 10 false CANL 2.01,3.156 2.469,3.354 0.458,0.198 10 false CG 0.323,2.583 0.625,2.781 0.302,0.198 10 false N8 0.146,0.104 0.458,0.302 0.313,0.198 10 false *a 0.146,1.823 0.698,2.115 0.552,0.292 10 false *b
*a Front view of wire harness connector
(to Steering Sensor)
*b Front view of DLC3


Disconnect the N3 steering sensor connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N3-3 (CANH) - N8-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
N3-8 (CANL) - N8-4 (CG)



c.

Reconnect the N3 steering sensor connector.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (STEERING SENSOR - NO. 4 CAN JUNCTION CONNECTOR)

33.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 4 CAN JUNCTION CONNECTOR - TIRE PRESSURE WARNING ECU AND RECEIVER)
a.

Disconnect the N177 No. 4 CAN junction connector.

HINT:
·

Before disconnecting the connectors, make a note of where it is connected.

·

Reconnect the connector to its original position.



C414819C02
5.823,2.104 6.25,2.354 0.427,0.25 3.927,2.833 4.281,2.573 4.281,2.573 4.448,2.573 true 3.927,2.99 4.26,3.219 4.26,3.219 4.427,3.219 true 5.969,2.875 6.156,3.563 6.156,3.563 6.323,3.563 true 4.479,2.521 5.094,2.719 0.615,0.198 10 false CANH 4.458,3.156 5.073,3.354 0.615,0.198 10 false CANL 1.281,2.417 1.896,2.615 0.615,0.198 10 false N121*B 1.281,2.167 1.896,2.365 0.615,0.198 10 false N120*B 2.917,2.198 3.531,2.396 0.615,0.198 10 false *a 0.146,0.083 0.76,0.281 0.615,0.198 10 false *1 1.271,2.656 1.885,2.854 0.615,0.198 10 false N177*B 1.271,2.885 1.885,3.083 0.615,0.198 10 false N120*A 1.26,1.917 1.875,2.115 0.615,0.198 10 false N119*B 1.271,1.667 1.885,1.865 0.615,0.198 10 false N118*B 1.813,2.646 2.427,2.844 0.615,0.198 10 false N121*A 5.083,1.875 5.698,2.073 0.615,0.198 10 false *b 5.958,2.167 6.271,2.365 0.313,0.198 10 false N8 6.354,3.479 6.729,3.688 0.375,0.208 10 false CG 1.271,3.135 1.885,3.333 0.615,0.198 10 false N119*A 1.271,3.385 1.885,3.583 0.615,0.198 10 false N118*A 1.802,2.396 2.417,2.594 0.615,0.198 10 false N123*A 1.802,2.156 2.417,2.354 0.615,0.198 10 false N177*A
*A for RHD *B for LHD
*1 No. 4 CAN Junction Connector - -
*a Rear view of wire harness connector
(to No. 4 CAN Junction Connector)
*b Front view of DLC3


Wiring Color
Code Color (CANH Side) Color (CANL Side) Connect to

*: w/ Variable Flow Control Solenoid Valve

N118 SB W Central gateway ECU (network gateway ECU)
N119 GR W Brake actuator assembly (skid control ECU)
N120 R W Airbag sensor assembly
N121 P W Steering sensor
N123 G W Power steering ECU assembly*
N177 B W Tire pressure warning ECU and receiver


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N177-1 (CANH) - N8-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
N177-2 (CANL) - N8-4 (CG)



c.

Reconnect the N177 No. 4 CAN junction connector.


Result:
Proceed to
OK
NG



OK

REPLACE NO. 4 CAN JUNCTION CONNECTOR

NG

34.CHECK FOR SHORT TO GND IN CAN BUS WIRE (TIRE PRESSURE WARNING ECU AND RECEIVER - NO. 4 CAN JUNCTION CONNECTOR)
34.CHECK FOR SHORT TO GND IN CAN BUS WIRE (TIRE PRESSURE WARNING ECU AND RECEIVER - NO. 4 CAN JUNCTION CONNECTOR)
a.
C414820C01
1.5,0.104 1.917,0.354 0.417,0.25 0.208,2.365 0.625,2.615 0.417,0.25 1.25,1.521 1.417,1.521 1.417,1.521 1.615,1.198 true 1.333,1.656 1.5,1.656 1.5,1.656 1.771,1.198 true 1.667,2.25 1.833,1.833 1.833,1.833 2,1.833 true 0.125,0.104 0.438,0.302 0.313,0.198 10 false *a 1.646,0.156 1.958,0.354 0.313,0.198 10 false Z3 0.844,1.427 1.26,1.615 0.417,0.188 10 false CANH 0.958,1.594 1.375,1.781 0.417,0.188 10 false CANL 2.052,1.76 2.365,1.958 0.313,0.198 10 false CG 0.333,2.406 0.646,2.604 0.313,0.198 10 false N8 0.125,1.958 0.438,2.156 0.313,0.198 10 false *b
*a Front view of wire harness connector
(to Tire Pressure Warning ECU and Receiver)
*b Front view of DLC3


Disconnect the Z3 tire pressure warning ECU and receiver connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Z3-9 (CANH) - N8-4 (CG) Cable disconnected from negative (-) battery terminal 200 Ω or higher
Z3-10 (CANL) - N8-4 (CG)



c.

Reconnect the Z3 tire pressure warning ECU and receiver connector.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (TIRE PRESSURE WARNING ECU AND RECEIVER - NO. 4 CAN JUNCTION CONNECTOR)

35.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU] - NO. 4 CAN JUNCTION CONNECTOR)
a.
C414215C04
1.479,0.26 1.917,0.469 0.438,0.208 1.438,2.542 1.875,2.75 0.438,0.208 2.656,0.646 2.438,0.646 2.438,0.646 2.427,1.26 true 2.573,4.26 2.406,4.26 2.406,4.26 2.365,3.635 true 2.542,2.156 2.323,2.156 2.323,2.156 2.313,1.521 true 1.573,0.292 2.188,0.49 0.615,0.198 10 false N21 1.542,2.573 2.156,2.771 0.615,0.198 10 false N8 0.094,0.073 0.708,0.271 0.615,0.198 10 false *a 0.104,2.563 0.719,2.76 0.615,0.198 10 false *b 2.698,0.573 3.229,0.781 0.531,0.208 10 false CA2L 2.615,4.188 2.969,4.375 0.354,0.188 10 false BAT 2.594,2.083 3.125,2.292 0.531,0.208 10 false CA2H
*a Front view of wire harness connector
(to Central Gateway ECU [Network Gateway ECU])
*b Front view of DLC3


Disconnect the N21 central gateway ECU (network gateway ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N21-22 (CA2H) - N8-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
N21-7 (CA2L) - N8-16 (BAT)



c.

Reconnect the N21 central gateway ECU (network gateway ECU) connector.


Result:
Proceed to
OK
NG



OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

36.CHECK VEHICLE TYPE
36.CHECK VEHICLE TYPE
a.

Check for vehicle type.


Result:
Result Proceed to
w/ Airbag System A
w/o Airbag System B



A

37.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (AIRBAG SENSOR ASSEMBLY - NO. 4 CAN JUNCTION CONNECTOR)

B

38.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 2 CAN JUNCTION TERMINAL - NO. 4 CAN JUNCTION CONNECTOR)
37.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (AIRBAG SENSOR ASSEMBLY - NO. 4 CAN JUNCTION CONNECTOR)
a.

Disconnect the N45 airbag sensor assembly connector.

for Type A: Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for Type A)>PRECAUTION

for Type B: Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for Type B)>PRECAUTION

for Type C: Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for Type C)>PRECAUTION

C414200C03
2.083,0.25 2.5,0.5 0.417,0.25 5.198,0.625 5.615,0.875 0.417,0.25 2.531,1.427 2.844,0.448 2.844,0.448 3.01,0.448 true 2.656,1.438 2.948,0.833 2.948,0.833 3.115,0.833 true 5.875,1.531 6.052,2.094 6.052,2.094 6.219,2.094 true 1.135,0.458 1.448,0.656 0.313,0.198 10 false *a 4.656,0.823 4.969,1.021 0.313,0.198 10 false *b 2.167,0.281 2.479,0.479 0.313,0.198 10 false N45 5.323,0.667 5.76,0.896 0.438,0.229 10 false N8 3.104,0.375 3.656,0.604 0.552,0.229 10 false CANH 3.177,0.781 3.729,1.01 0.552,0.229 10 false CANL 6.271,2.01 6.823,2.24 0.552,0.229 10 false BAT
*a Front view of wire harness connector
(to Airbag Sensor Assembly)
*b Front view of DLC3



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N45-26 (CANH) - N8-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
N45-27 (CANL) - N8-16 (BAT)



c.

Reconnect the N45 airbag sensor assembly connector.


Result:
Proceed to
OK
NG



OK

NG

39.CHECK VEHICLE TYPE
38.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 2 CAN JUNCTION TERMINAL - NO. 4 CAN JUNCTION CONNECTOR)
a.
C414349C02
0.365,0.781 0.854,1.042 0.49,0.26 0.125,2.385 0.615,2.646 0.49,0.26 2.365,2.719 2.49,3.115 2.49,3.115 2.625,3.115 true 1.938,0.885 2.208,0.406 2.208,0.406 2.344,0.406 true 1.292,0.427 1.448,0.427 1.448,0.427 1.729,0.906 true 0.458,0.833 1.073,1.031 0.615,0.198 10 false N122 0.292,2.438 0.906,2.635 0.615,0.198 10 false N8 2.677,3.031 3.125,3.25 0.448,0.219 10 false BAT 2.375,0.323 2.99,0.521 0.615,0.198 10 false CANH 0.885,0.344 1.5,0.542 0.615,0.198 10 false CANL 0.135,0.104 0.448,0.302 0.313,0.198 10 false *a 0.135,1.594 0.448,1.792 0.313,0.198 10 false *b
*a Front view of wire harness connector
(to No. 2 CAN Junction Terminal)
*b Front view of DLC3


Disconnect the N122 No. 2 CAN junction terminal connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N122-3 (CANH) - N8-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
N122-2 (CANL) - N8-16 (BAT)



c.

Reconnect the N122 No. 2 CAN junction terminal connector.


Result:
Proceed to
OK
NG



OK

REPLACE NO. 2 CAN JUNCTION TERMINAL

NG

47.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 4 CAN JUNCTION CONNECTOR - NO. 2 CAN JUNCTION TERMINAL)
39.CHECK VEHICLE TYPE
a.

Check for vehicle type.


Result:
Result Proceed to
except Wagon A
for Wagon B



A

40.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 4 CAN JUNCTION CONNECTOR - AIRBAG SENSOR ASSEMBLY)

B

53.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 4 CAN JUNCTION CONNECTOR - AIRBAG SENSOR ASSEMBLY)
40.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 4 CAN JUNCTION CONNECTOR - AIRBAG SENSOR ASSEMBLY)
a.

Disconnect the N120 No. 4 CAN junction connector.

HINT:
·

Before disconnecting the connectors, make a note of where it is connected.

·

Reconnect the connector to its original position.



C414491C02
5.823,2.104 6.25,2.354 0.427,0.25 3.927,2.833 4.281,2.573 4.281,2.573 4.448,2.573 true 3.927,2.99 4.26,3.219 4.26,3.219 4.427,3.219 true 6.302,3.563 6.448,3.563 6.448,3.563 6.573,3.167 true 4.479,2.521 5.094,2.719 0.615,0.198 10 false CANH 4.458,3.156 5.073,3.354 0.615,0.198 10 false CANL 1.281,2.438 1.896,2.635 0.615,0.198 10 false N121 1.281,2.198 1.896,2.396 0.615,0.198 10 false N120 2.917,2.198 3.531,2.396 0.615,0.198 10 false *a 0.146,0.083 0.76,0.281 0.615,0.198 10 false *1 1.281,2.688 1.896,2.885 0.615,0.198 10 false N123 1.281,1.948 1.896,2.146 0.615,0.198 10 false N119 1.281,1.667 1.896,1.865 0.615,0.198 10 false N118 5.083,1.875 5.698,2.073 0.615,0.198 10 false *b 5.958,2.167 6.271,2.365 0.313,0.198 10 false N8 5.969,3.469 6.344,3.677 0.375,0.208 10 false BAT
*1 No. 4 CAN Junction Connector - -
*a Rear view of wire harness connector
(to No. 4 CAN Junction Connector)
*b Front view of DLC3


Wiring Color
Code Color (CANH Side) Color (CANL Side) Connect to

*1: w/ VSC OFF Switch

*2: w/o VSC OFF Switch

*3: w/ Variable Flow Control Solenoid Valve

N118 SB W Central gateway ECU (network gateway ECU)
N119 GR W Brake actuator assembly (skid control ECU)
N120 R W Airbag sensor assembly
N121 P W
·

Steering sensor*1

·

Combination switch ECU sub-assembly*2


N123 G W Power steering ECU assembly*3


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N120-1 (CANH) - N8-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
N120-2 (CANL) - N8-16 (BAT)



c.

Reconnect the N120 No. 4 CAN junction connector.


Result:
Proceed to
OK
NG



OK

41.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 4 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU])

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 4 CAN JUNCTION CONNECTOR - AIRBAG SENSOR ASSEMBLY)

41.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 4 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU])
a.

Disconnect the N118 No. 4 CAN junction connector.

HINT:
·

Before disconnecting the connectors, make a note of where it is connected.

·

Reconnect the connector to its original position.



C414350C02
5.823,2.104 6.25,2.354 0.427,0.25 3.927,2.833 4.281,2.573 4.281,2.573 4.448,2.573 true 3.927,2.99 4.26,3.219 4.26,3.219 4.427,3.219 true 6.302,3.563 6.448,3.563 6.448,3.563 6.573,3.167 true 4.479,2.521 5.094,2.719 0.615,0.198 10 false CANH 4.458,3.156 5.073,3.354 0.615,0.198 10 false CANL 1.281,2.438 1.896,2.635 0.615,0.198 10 false N121 1.281,2.198 1.896,2.396 0.615,0.198 10 false N120 2.917,2.198 3.531,2.396 0.615,0.198 10 false *a 0.146,0.083 0.76,0.281 0.615,0.198 10 false *1 1.281,2.688 1.896,2.885 0.615,0.198 10 false N123*A 1.281,2.927 1.896,3.125 0.615,0.198 10 false N124*A 1.281,1.948 1.896,2.146 0.615,0.198 10 false N119 1.281,1.667 1.896,1.865 0.615,0.198 10 false N118 1.823,2.688 2.438,2.885 0.615,0.198 10 false N124*B 5.083,1.875 5.698,2.073 0.615,0.198 10 false *b 5.958,2.167 6.271,2.365 0.313,0.198 10 false N8 5.969,3.469 6.344,3.677 0.375,0.208 10 false BAT
*A for RHD *B for LHD
*1 No. 4 CAN Junction Connector - -
*a Rear view of wire harness connector
(to No. 4 CAN Junction Connector)
*b Front view of DLC3


Wiring Color
Code Color (CANH Side) Color (CANL Side) Connect to

*1: w/ Airbag System

*2: w/ VSC OFF Switch

*3: w/o VSC OFF Switch

*4: w/ Variable Flow Control Solenoid Valve

*5: w/o Airbag System

N118 SB W Central gateway ECU (network gateway ECU)
N119 GR W Brake actuator assembly (skid control ECU)
N120 R W Airbag sensor assembly*1
N121 P W
·

Steering sensor*2

·

Combination switch ECU sub-assembly*3


N123 G W Power steering ECU assembly*4
N124 L W No. 2 CAN junction terminal*5


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N118-1 (CANH) - N8-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
N118-2 (CANL) - N8-16 (BAT)



c.

Reconnect the N118 No. 4 CAN junction connector.


Result:
Proceed to
OK
NG



OK

42.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 4 CAN JUNCTION CONNECTOR - BRAKE ACTUATOR ASSEMBLY [SKID CONTROL ECU])

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 4 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU])

42.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 4 CAN JUNCTION CONNECTOR - BRAKE ACTUATOR ASSEMBLY [SKID CONTROL ECU])
a.

Disconnect the N119 No. 4 CAN junction connector.

HINT:
·

Before disconnecting the connectors, make a note of where it is connected.

·

Reconnect the connector to its original position.



C414350C02
5.823,2.104 6.25,2.354 0.427,0.25 3.927,2.833 4.281,2.573 4.281,2.573 4.448,2.573 true 3.927,2.99 4.26,3.219 4.26,3.219 4.427,3.219 true 6.302,3.563 6.448,3.563 6.448,3.563 6.573,3.167 true 4.479,2.521 5.094,2.719 0.615,0.198 10 false CANH 4.458,3.156 5.073,3.354 0.615,0.198 10 false CANL 1.281,2.438 1.896,2.635 0.615,0.198 10 false N121 1.281,2.198 1.896,2.396 0.615,0.198 10 false N120 2.917,2.198 3.531,2.396 0.615,0.198 10 false *a 0.146,0.083 0.76,0.281 0.615,0.198 10 false *1 1.281,2.688 1.896,2.885 0.615,0.198 10 false N123*A 1.281,2.927 1.896,3.125 0.615,0.198 10 false N124*A 1.281,1.948 1.896,2.146 0.615,0.198 10 false N119 1.281,1.667 1.896,1.865 0.615,0.198 10 false N118 1.823,2.688 2.438,2.885 0.615,0.198 10 false N124*B 5.083,1.875 5.698,2.073 0.615,0.198 10 false *b 5.958,2.167 6.271,2.365 0.313,0.198 10 false N8 5.969,3.469 6.344,3.677 0.375,0.208 10 false BAT
*A for RHD *B for LHD
*1 No. 4 CAN Junction Connector - -
*a Rear view of wire harness connector
(to No. 4 CAN Junction Connector)
*b Front view of DLC3


Wiring Color
Code Color (CANH Side) Color (CANL Side) Connect to

*1: w/ Airbag System

*2: w/ VSC OFF Switch

*3: w/o VSC OFF Switch

*4: w/ Variable Flow Control Solenoid Valve

*5: w/o Airbag System

N118 SB W Central gateway ECU (network gateway ECU)
N119 GR W Brake actuator assembly (skid control ECU)
N120 R W Airbag sensor assembly*1
N121 P W
·

Steering sensor*2

·

Combination switch ECU sub-assembly*3


N123 G W Power steering ECU assembly*4
N124 L W No. 2 CAN junction terminal*5


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N119-1 (CANH) - N8-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
N119-2 (CANL) - N8-16 (BAT)



c.

Reconnect the N119 No. 4 CAN junction connector.


Result:
Proceed to
OK
NG



OK

43.CHECK VEHICLE TYPE

NG

48.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (BRAKE ACTUATOR ASSEMBLY [SKID CONTROL ECU] - NO. 4 CAN JUNCTION CONNECTOR)
43.CHECK VEHICLE TYPE
a.

Check for vehicle type.


Result:
Result Proceed to
w/ Variable Flow Control Solenoid Valve A
w/o Variable Flow Control Solenoid Valve B



A

44.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 4 CAN JUNCTION CONNECTOR - POWER STEERING ECU ASSEMBLY)

B

45.CHECK VEHICLE TYPE
44.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 4 CAN JUNCTION CONNECTOR - POWER STEERING ECU ASSEMBLY)
a.

Disconnect the N123 No. 4 CAN junction connector.

HINT:
·

Before disconnecting the connectors, make a note of where it is connected.

·

Reconnect the connector to its original position.



C414492C02
5.823,2.104 6.25,2.354 0.427,0.25 3.927,2.833 4.281,2.573 4.281,2.573 4.448,2.573 true 3.927,2.99 4.26,3.219 4.26,3.219 4.427,3.219 true 6.302,3.563 6.448,3.563 6.448,3.563 6.573,3.167 true 4.479,2.521 5.094,2.719 0.615,0.198 10 false CANH 4.458,3.156 5.073,3.354 0.615,0.198 10 false CANL 1.281,2.438 1.896,2.635 0.615,0.198 10 false N121 1.281,2.198 1.896,2.396 0.615,0.198 10 false N120 2.917,2.198 3.531,2.396 0.615,0.198 10 false *a 0.146,0.083 0.76,0.281 0.615,0.198 10 false *1 1.281,2.688 1.896,2.885 0.615,0.198 10 false N123 1.281,2.927 1.896,3.125 0.615,0.198 10 false N124 1.281,1.948 1.896,2.146 0.615,0.198 10 false N119 1.281,1.667 1.896,1.865 0.615,0.198 10 false N118 5.083,1.875 5.698,2.073 0.615,0.198 10 false *b 5.958,2.167 6.271,2.365 0.313,0.198 10 false N8 5.969,3.469 6.344,3.677 0.375,0.208 10 false BAT
*1 No. 4 CAN Junction Connector - -
*a Rear view of wire harness connector
(to No. 4 CAN Junction Connector)
*b Front view of DLC3


Wiring Color
Code Color (CANH Side) Color (CANL Side) Connect to

*1: w/ Airbag System

*2: w/ VSC OFF Switch

*3: w/o VSC OFF Switch

*4: w/o Airbag System

N118 SB W Central gateway ECU (network gateway ECU)
N119 GR W Brake actuator assembly (skid control ECU)
N120 R W Airbag sensor assembly*1
N121 P W
·

Steering sensor*2

·

Combination switch ECU sub-assembly*3


N123 G W Power steering ECU assembly
N124 L W No. 2 CAN junction terminal*4


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N123-1 (CANH) - N8-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
N123-2 (CANL) - N8-16 (BAT)



c.

Reconnect the N123 No. 4 CAN junction connector.


Result:
Proceed to
OK
NG



OK

45.CHECK VEHICLE TYPE

NG

49.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (POWER STEERING ECU ASSEMBLY - NO. 4 CAN JUNCTION CONNECTOR)
45.CHECK VEHICLE TYPE
a.

Check for vehicle type.


Result:
Result Proceed to
w/ VSC OFF Switch A
w/o VSC OFF Switch B



A

46.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 4 CAN JUNCTION CONNECTOR - STEERING SENSOR)

B

50.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 4 CAN JUNCTION CONNECTOR - COMBINATION SWITCH ECU SUB-ASSEMBLY)
46.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 4 CAN JUNCTION CONNECTOR - STEERING SENSOR)
a.

Disconnect the N121 No. 4 CAN junction connector.

HINT:
·

Before disconnecting the connectors, make a note of where it is connected.

·

Reconnect the connector to its original position.



C414350C02
5.823,2.104 6.25,2.354 0.427,0.25 3.927,2.833 4.281,2.573 4.281,2.573 4.448,2.573 true 3.927,2.99 4.26,3.219 4.26,3.219 4.427,3.219 true 6.302,3.563 6.448,3.563 6.448,3.563 6.573,3.167 true 4.479,2.521 5.094,2.719 0.615,0.198 10 false CANH 4.458,3.156 5.073,3.354 0.615,0.198 10 false CANL 1.281,2.438 1.896,2.635 0.615,0.198 10 false N121 1.281,2.198 1.896,2.396 0.615,0.198 10 false N120 2.917,2.198 3.531,2.396 0.615,0.198 10 false *a 0.146,0.083 0.76,0.281 0.615,0.198 10 false *1 1.281,2.688 1.896,2.885 0.615,0.198 10 false N123*A 1.281,2.927 1.896,3.125 0.615,0.198 10 false N124*A 1.281,1.948 1.896,2.146 0.615,0.198 10 false N119 1.281,1.667 1.896,1.865 0.615,0.198 10 false N118 1.823,2.688 2.438,2.885 0.615,0.198 10 false N124*B 5.083,1.875 5.698,2.073 0.615,0.198 10 false *b 5.958,2.167 6.271,2.365 0.313,0.198 10 false N8 5.969,3.469 6.344,3.677 0.375,0.208 10 false BAT
*A for RHD *B for LHD
*1 No. 4 CAN Junction Connector - -
*a Rear view of wire harness connector
(to No. 4 CAN Junction Connector)
*b Front view of DLC3


Wiring Color
Code Color (CANH Side) Color (CANL Side) Connect to

*1: w/ Airbag System

*2: w/ Variable Flow Control Solenoid Valve

*3: w/o Airbag System

N118 SB W Central gateway ECU (network gateway ECU)
N119 GR W Brake actuator assembly (skid control ECU)
N120 R W Airbag sensor assembly*1
N121 P W Steering sensor
N123 G W Power steering ECU assembly*2
N124 L W No. 2 CAN junction terminal*3


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N121-1 (CANH) - N8-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
N121-2 (CANL) - N8-16 (BAT)



c.

Reconnect the N121 No. 4 CAN junction connector.


Result:
Proceed to
OK
NG



OK

REPLACE NO. 4 CAN JUNCTION CONNECTOR

NG

51.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (STEERING SENSOR - NO. 4 CAN JUNCTION CONNECTOR)
47.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 4 CAN JUNCTION CONNECTOR - NO. 2 CAN JUNCTION TERMINAL)
a.

Disconnect the N124 No. 4 CAN junction connector.

HINT:
·

Before disconnecting the connectors, make a note of where it is connected.

·

Reconnect the connector to its original position.



C414490C02
5.823,2.104 6.25,2.354 0.427,0.25 3.927,2.833 4.281,2.573 4.281,2.573 4.448,2.573 true 3.927,2.99 4.26,3.219 4.26,3.219 4.427,3.219 true 6.573,3.167 6.406,3.594 6.406,3.594 6.573,3.594 true 4.479,2.521 5.094,2.719 0.615,0.198 10 false CANH 4.458,3.156 5.073,3.354 0.615,0.198 10 false CANL 1.281,2.438 1.896,2.635 0.615,0.198 10 false N121 2.917,2.198 3.531,2.396 0.615,0.198 10 false *a 0.146,0.083 0.76,0.281 0.615,0.198 10 false *1 1.281,2.688 1.896,2.885 0.615,0.198 10 false N123*A 1.281,2.927 1.896,3.125 0.615,0.198 10 false N124*A 1.281,1.948 1.896,2.146 0.615,0.198 10 false N119 1.281,1.667 1.896,1.865 0.615,0.198 10 false N118 1.823,2.688 2.438,2.885 0.615,0.198 10 false N124*B 5.083,1.875 5.698,2.073 0.615,0.198 10 false *b 5.958,2.167 6.271,2.365 0.313,0.198 10 false N8 6.625,3.521 7,3.729 0.375,0.208 10 false BAT
*A for RHD *B for LHD
*1 No. 4 CAN Junction Connector - -
*a Rear view of wire harness connector
(to No. 4 CAN Junction Connector)
*b Front view of DLC3


Wiring Color
Code Color (CANH Side) Color (CANL Side) Connect to

*1: w/ VSC OFF Switch

*2: w/o VSC OFF Switch

*3: w/ Variable Flow Control Solenoid Valve

N118 SB W Central gateway ECU (network gateway ECU)
N119 GR W Brake actuator assembly (skid control ECU)
N121 P W
·

Steering sensor*1

·

Combination switch ECU sub-assembly*2


N123 G W Power steering ECU assembly*3
N124 L W No. 2 CAN junction terminal


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N124-1 (CANH) - N8-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
N124-2 (CANL) - N8-16 (BAT)



c.

Reconnect the N124 No. 4 CAN junction connector.


Result:
Proceed to
OK
NG



OK

41.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 4 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU])

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 4 CAN JUNCTION CONNECTOR - NO. 2 CAN JUNCTION TERMINAL)

48.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (BRAKE ACTUATOR ASSEMBLY [SKID CONTROL ECU] - NO. 4 CAN JUNCTION CONNECTOR)
a.
C414351C02
1.479,0.313 1.927,0.573 0.448,0.26 1.479,2.677 1.927,2.938 0.448,0.26 2.615,4.354 2.479,4.354 2.479,4.354 2.354,3.948 true 1.313,2.198 1.177,2.198 1.177,2.198 0.99,1.583 true 1.229,0.823 1.094,0.823 1.094,0.823 0.896,1.281 true 0.094,0.073 0.427,0.396 0.333,0.323 10 false *a 0.094,2.594 0.5,2.938 0.406,0.344 10 false *b 1.583,0.365 2.042,0.563 0.458,0.198 10 false A28 1.625,2.74 2.083,2.938 0.458,0.198 10 false N8 2.656,4.26 2.969,4.458 0.313,0.198 10 false BAT 1.354,2.115 1.969,2.313 0.615,0.198 10 false CANL 1.26,0.729 1.875,0.927 0.615,0.198 10 false CANH
*a Front view of wire harness connector
(to Brake Actuator Assembly [Skid Control ECU])
*b Front view of DLC3


Disconnect the A28 brake actuator assembly (skid control ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A28-26 (CANH) - N8-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
A28-14 (CANL) - N8-16 (BAT)



c.

Reconnect the A28 brake actuator assembly (skid control ECU) connector.


Result:
Proceed to
OK
NG



OK

REPLACE BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU)

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (BRAKE ACTUATOR ASSEMBLY [SKID CONTROL ECU] - NO. 4 CAN JUNCTION CONNECTOR)

49.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (POWER STEERING ECU ASSEMBLY - NO. 4 CAN JUNCTION CONNECTOR)
a.
C379614C06
0.24,0.99 0.594,1.188 0.354,0.198 0.167,2.333 0.521,2.531 0.354,0.198 0.833,1.792 1.021,1.792 1.021,1.792 1.125,1.271 true 1.542,0.333 1.375,0.333 1.375,0.333 1.302,1.135 true 2.573,3.104 2.406,3.104 2.406,3.104 2.208,2.604 true 0.354,0.135 0.667,0.333 0.313,0.198 10 false *a 0.427,1.729 0.938,1.938 0.51,0.208 10 false CANH 1.583,0.26 2.094,0.469 0.51,0.208 10 false CANL 0.292,1.01 0.802,1.219 0.51,0.208 10 false N36 0.24,2.354 0.75,2.563 0.51,0.208 10 false N8 2.625,3.021 3.135,3.229 0.51,0.208 10 false BAT 0.25,2.01 0.563,2.208 0.313,0.198 10 false *b
*a Front view of wire harness connector
(to Power Steering ECU Assembly)
*b Front view of DLC3


Disconnect the N36 power steering ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N36-1 (CANH) - N8-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
N36-2 (CANL) - N8-16 (BAT)



c.

Reconnect the N36 power steering ECU assembly connector.


Result:
Proceed to
OK
NG



OK

REPLACE POWER STEERING ECU ASSEMBLY

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (POWER STEERING ECU ASSEMBLY - NO. 4 CAN JUNCTION CONNECTOR)

50.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 4 CAN JUNCTION CONNECTOR - COMBINATION SWITCH ECU SUB-ASSEMBLY)
a.

Disconnect the N121 No. 4 CAN junction connector.

HINT:
·

Before disconnecting the connectors, make a note of where it is connected.

·

Reconnect the connector to its original position.



C414350C02
5.823,2.104 6.25,2.354 0.427,0.25 3.927,2.833 4.281,2.573 4.281,2.573 4.448,2.573 true 3.927,2.99 4.26,3.219 4.26,3.219 4.427,3.219 true 6.302,3.563 6.448,3.563 6.448,3.563 6.573,3.167 true 4.479,2.521 5.094,2.719 0.615,0.198 10 false CANH 4.458,3.156 5.073,3.354 0.615,0.198 10 false CANL 1.281,2.438 1.896,2.635 0.615,0.198 10 false N121 1.281,2.198 1.896,2.396 0.615,0.198 10 false N120 2.917,2.198 3.531,2.396 0.615,0.198 10 false *a 0.146,0.083 0.76,0.281 0.615,0.198 10 false *1 1.281,2.688 1.896,2.885 0.615,0.198 10 false N123*A 1.281,2.927 1.896,3.125 0.615,0.198 10 false N124*A 1.281,1.948 1.896,2.146 0.615,0.198 10 false N119 1.281,1.667 1.896,1.865 0.615,0.198 10 false N118 1.823,2.688 2.438,2.885 0.615,0.198 10 false N124*B 5.083,1.875 5.698,2.073 0.615,0.198 10 false *b 5.958,2.167 6.271,2.365 0.313,0.198 10 false N8 5.969,3.469 6.344,3.677 0.375,0.208 10 false BAT
*A for RHD *B for LHD
*1 No. 4 CAN Junction Connector - -
*a Rear view of wire harness connector
(to No. 4 CAN Junction Connector)
*b Front view of DLC3


Wiring Color
Code Color (CANH Side) Color (CANL Side) Connect to

*1: w/ Airbag System

*2: w/ Variable Flow Control Solenoid Valve

*3: w/o Airbag System

N118 SB W Central gateway ECU (network gateway ECU)
N119 GR W Brake actuator assembly (skid control ECU)
N120 R W Airbag sensor assembly*1
N121 P W Combination switch ECU sub-assembly
N123 G W Power steering ECU assembly*2
N124 L W No. 2 CAN junction terminal*3


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N121-1 (CANH) - N8-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
N121-2 (CANL) - N8-16 (BAT)



c.

Reconnect the N121 No. 4 CAN junction connector.


Result:
Proceed to
OK
NG



OK

REPLACE NO. 4 CAN JUNCTION CONNECTOR

NG

52.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (COMBINATION SWITCH ECU SUB-ASSEMBLY - NO. 4 CAN JUNCTION CONNECTOR)
51.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (STEERING SENSOR - NO. 4 CAN JUNCTION CONNECTOR)
a.
C414352C02
0.427,0.865 0.865,1.104 0.438,0.24 0.188,2.542 0.625,2.781 0.438,0.24 2.354,2.844 2.479,3.24 2.479,3.24 2.604,3.24 true 1.719,1.271 1.833,1.75 1.833,1.75 1.958,1.75 true 1.708,0.948 1.833,0.229 1.833,0.229 1.958,0.229 true 0.573,0.906 0.875,1.104 0.302,0.198 10 false N3 1.99,0.146 2.448,0.344 0.458,0.198 10 false CANH 2,1.667 2.458,1.865 0.458,0.198 10 false CANL 2.656,3.156 3.115,3.354 0.458,0.198 10 false BAT 0.323,2.583 0.625,2.781 0.302,0.198 10 false N8 0.146,0.104 0.458,0.302 0.313,0.198 10 false *a 0.146,1.823 0.698,2.115 0.552,0.292 10 false *b
*a Front view of wire harness connector
(to Steering Sensor)
*b Front view of DLC3


Disconnect the N3 steering sensor connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N3-3 (CANH) - N8-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
N3-8 (CANL) - N8-16 (BAT)



c.

Reconnect the N3 steering sensor connector.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (STEERING SENSOR - NO. 4 CAN JUNCTION CONNECTOR)

52.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (COMBINATION SWITCH ECU SUB-ASSEMBLY - NO. 4 CAN JUNCTION CONNECTOR)
a.
C414352C02
0.427,0.865 0.865,1.104 0.438,0.24 0.188,2.542 0.625,2.781 0.438,0.24 2.354,2.844 2.479,3.24 2.479,3.24 2.604,3.24 true 1.719,1.271 1.833,1.75 1.833,1.75 1.958,1.75 true 1.708,0.948 1.833,0.229 1.833,0.229 1.958,0.229 true 0.573,0.906 0.875,1.104 0.302,0.198 10 false N3 1.99,0.146 2.448,0.344 0.458,0.198 10 false CANH 2,1.667 2.458,1.865 0.458,0.198 10 false CANL 2.656,3.156 3.115,3.354 0.458,0.198 10 false BAT 0.323,2.583 0.625,2.781 0.302,0.198 10 false N8 0.146,0.104 0.458,0.302 0.313,0.198 10 false *a 0.146,1.823 0.698,2.115 0.552,0.292 10 false *b
*a Front view of wire harness connector
(to Combination Switch ECU Sub-assembly)
*b Front view of DLC3


Disconnect the N3 combination switch ECU sub-assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N3-3 (CANH) - N8-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
N3-8 (CANL) - N8-16 (BAT)



c.

Reconnect the N3 combination switch ECU sub-assembly connector.


Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION SWITCH ECU SUB-ASSEMBLY

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (COMBINATION SWITCH ECU SUB-ASSEMBLY - NO. 4 CAN JUNCTION CONNECTOR)

53.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 4 CAN JUNCTION CONNECTOR - AIRBAG SENSOR ASSEMBLY)
a.

Disconnect the N120 No. 4 CAN junction connector.

HINT:
·

Before disconnecting the connectors, make a note of where it is connected.

·

Reconnect the connector to its original position.



C414819C03
5.823,2.104 6.25,2.354 0.427,0.25 3.927,2.833 4.281,2.573 4.281,2.573 4.448,2.573 true 3.927,2.99 4.26,3.219 4.26,3.219 4.427,3.219 true 6.542,3.188 6.542,3.615 6.542,3.615 6.708,3.615 true 4.479,2.521 5.094,2.719 0.615,0.198 10 false CANH 4.458,3.156 5.073,3.354 0.615,0.198 10 false CANL 1.281,2.417 1.896,2.615 0.615,0.198 10 false N121*B 1.281,2.167 1.896,2.365 0.615,0.198 10 false N120*B 2.917,2.198 3.531,2.396 0.615,0.198 10 false *a 0.146,0.083 0.76,0.281 0.615,0.198 10 false *1 1.271,2.656 1.885,2.854 0.615,0.198 10 false N177*B 1.271,2.885 1.885,3.083 0.615,0.198 10 false N120*A 1.26,1.917 1.875,2.115 0.615,0.198 10 false N119*B 1.271,1.667 1.885,1.865 0.615,0.198 10 false N118*B 1.813,2.646 2.427,2.844 0.615,0.198 10 false N121*A 5.083,1.875 5.698,2.073 0.615,0.198 10 false *b 5.958,2.167 6.271,2.365 0.313,0.198 10 false N8 6.781,3.531 7.156,3.74 0.375,0.208 10 false BAT 1.271,3.135 1.885,3.333 0.615,0.198 10 false N119*A 1.271,3.385 1.885,3.583 0.615,0.198 10 false N118*A 1.802,2.396 2.417,2.594 0.615,0.198 10 false N123*A 1.802,2.156 2.417,2.354 0.615,0.198 10 false N177*A
*A for RHD *B for LHD
*1 No. 4 CAN Junction Connector - -
*a Rear view of wire harness connector
(to No. 4 CAN Junction Connector)
*b Front view of DLC3


Wiring Color
Code Color (CANH Side) Color (CANL Side) Connect to

*1: w/ Variable Flow Control Solenoid Valve

*2: w/ Tire Pressure Warning System (Tire Inflation Pressure Display Function)

N118 SB W Central gateway ECU (network gateway ECU)
N119 GR W Brake actuator assembly (skid control ECU)
N120 R W Airbag sensor assembly
N121 P W Steering sensor
N123 G W Power steering ECU assembly*1
N177 B W Tire pressure warning ECU and receiver*2


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N120-1 (CANH) - N8-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
N120-2 (CANL) - N8-16 (BAT)



c.

Reconnect the N120 No. 4 CAN junction connector.


Result:
Proceed to
OK
NG



OK

54.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 4 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU])

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 4 CAN JUNCTION CONNECTOR - AIRBAG SENSOR ASSEMBLY)

54.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 4 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU])
a.

Disconnect the N118 No. 4 CAN junction connector.

HINT:
·

Before disconnecting the connectors, make a note of where it is connected.

·

Reconnect the connector to its original position.



C414819C03
5.823,2.104 6.25,2.354 0.427,0.25 3.927,2.833 4.281,2.573 4.281,2.573 4.448,2.573 true 3.927,2.99 4.26,3.219 4.26,3.219 4.427,3.219 true 6.542,3.188 6.542,3.615 6.542,3.615 6.708,3.615 true 4.479,2.521 5.094,2.719 0.615,0.198 10 false CANH 4.458,3.156 5.073,3.354 0.615,0.198 10 false CANL 1.281,2.417 1.896,2.615 0.615,0.198 10 false N121*B 1.281,2.167 1.896,2.365 0.615,0.198 10 false N120*B 2.917,2.198 3.531,2.396 0.615,0.198 10 false *a 0.146,0.083 0.76,0.281 0.615,0.198 10 false *1 1.271,2.656 1.885,2.854 0.615,0.198 10 false N177*B 1.271,2.885 1.885,3.083 0.615,0.198 10 false N120*A 1.26,1.917 1.875,2.115 0.615,0.198 10 false N119*B 1.271,1.667 1.885,1.865 0.615,0.198 10 false N118*B 1.813,2.646 2.427,2.844 0.615,0.198 10 false N121*A 5.083,1.875 5.698,2.073 0.615,0.198 10 false *b 5.958,2.167 6.271,2.365 0.313,0.198 10 false N8 6.781,3.531 7.156,3.74 0.375,0.208 10 false BAT 1.271,3.135 1.885,3.333 0.615,0.198 10 false N119*A 1.271,3.385 1.885,3.583 0.615,0.198 10 false N118*A 1.802,2.396 2.417,2.594 0.615,0.198 10 false N123*A 1.802,2.156 2.417,2.354 0.615,0.198 10 false N177*A
*A for RHD *B for LHD
*1 No. 4 CAN Junction Connector - -
*a Rear view of wire harness connector
(to No. 4 CAN Junction Connector)
*b Front view of DLC3


Wiring Color
Code Color (CANH Side) Color (CANL Side) Connect to

*1: w/ Variable Flow Control Solenoid Valve

*2: w/ Tire Pressure Warning System (Tire Inflation Pressure Display Function)

N118 SB W Central gateway ECU (network gateway ECU)
N119 GR W Brake actuator assembly (skid control ECU)
N120 R W Airbag sensor assembly
N121 P W Steering sensor
N123 G W Power steering ECU assembly*1
N177 B W Tire pressure warning ECU and receiver*2


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N118-1 (CANH) - N8-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
N118-2 (CANL) - N8-16 (BAT)



c.

Reconnect the N118 No. 4 CAN junction connector.


Result:
Proceed to
OK
NG



OK

55.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 4 CAN JUNCTION CONNECTOR - BRAKE ACTUATOR ASSEMBLY [SKID CONTROL ECU])

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 4 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU])

55.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 4 CAN JUNCTION CONNECTOR - BRAKE ACTUATOR ASSEMBLY [SKID CONTROL ECU])
a.

Disconnect the N119 No. 4 CAN junction connector.

HINT:
·

Before disconnecting the connectors, make a note of where it is connected.

·

Reconnect the connector to its original position.



C414819C03
5.823,2.104 6.25,2.354 0.427,0.25 3.927,2.833 4.281,2.573 4.281,2.573 4.448,2.573 true 3.927,2.99 4.26,3.219 4.26,3.219 4.427,3.219 true 6.542,3.188 6.542,3.615 6.542,3.615 6.708,3.615 true 4.479,2.521 5.094,2.719 0.615,0.198 10 false CANH 4.458,3.156 5.073,3.354 0.615,0.198 10 false CANL 1.281,2.417 1.896,2.615 0.615,0.198 10 false N121*B 1.281,2.167 1.896,2.365 0.615,0.198 10 false N120*B 2.917,2.198 3.531,2.396 0.615,0.198 10 false *a 0.146,0.083 0.76,0.281 0.615,0.198 10 false *1 1.271,2.656 1.885,2.854 0.615,0.198 10 false N177*B 1.271,2.885 1.885,3.083 0.615,0.198 10 false N120*A 1.26,1.917 1.875,2.115 0.615,0.198 10 false N119*B 1.271,1.667 1.885,1.865 0.615,0.198 10 false N118*B 1.813,2.646 2.427,2.844 0.615,0.198 10 false N121*A 5.083,1.875 5.698,2.073 0.615,0.198 10 false *b 5.958,2.167 6.271,2.365 0.313,0.198 10 false N8 6.781,3.531 7.156,3.74 0.375,0.208 10 false BAT 1.271,3.135 1.885,3.333 0.615,0.198 10 false N119*A 1.271,3.385 1.885,3.583 0.615,0.198 10 false N118*A 1.802,2.396 2.417,2.594 0.615,0.198 10 false N123*A 1.802,2.156 2.417,2.354 0.615,0.198 10 false N177*A
*A for RHD *B for LHD
*1 No. 4 CAN Junction Connector - -
*a Rear view of wire harness connector
(to No. 4 CAN Junction Connector)
*b Front view of DLC3


Wiring Color
Code Color (CANH Side) Color (CANL Side) Connect to

*1: w/ Variable Flow Control Solenoid Valve

*2: w/ Tire Pressure Warning System (Tire Inflation Pressure Display Function)

N118 SB W Central gateway ECU (network gateway ECU)
N119 GR W Brake actuator assembly (skid control ECU)
N120 R W Airbag sensor assembly
N121 P W Steering sensor
N123 G W Power steering ECU assembly*1
N177 B W Tire pressure warning ECU and receiver*2


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N119-1 (CANH) - N8-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
N119-2 (CANL) - N8-16 (BAT)



c.

Reconnect the N119 No. 4 CAN junction connector.


Result:
Proceed to
OK
NG



OK

56.CHECK VEHICLE TYPE

NG

60.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (BRAKE ACTUATOR ASSEMBLY [SKID CONTROL ECU] - NO. 4 CAN JUNCTION CONNECTOR)
56.CHECK VEHICLE TYPE
a.

Check for vehicle type.


Result:
Result Proceed to
w/ Variable Flow Control Solenoid Valve A
w/o Variable Flow Control Solenoid Valve B



A

57.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 4 CAN JUNCTION CONNECTOR - POWER STEERING ECU ASSEMBLY)

B

58.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 4 CAN JUNCTION CONNECTOR - STEERING SENSOR)
57.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 4 CAN JUNCTION CONNECTOR - POWER STEERING ECU ASSEMBLY)
a.

Disconnect the N123 No. 4 CAN junction connector.

HINT:
·

Before disconnecting the connectors, make a note of where it is connected.

·

Reconnect the connector to its original position.



C414819C03
5.823,2.104 6.25,2.354 0.427,0.25 3.927,2.833 4.281,2.573 4.281,2.573 4.448,2.573 true 3.927,2.99 4.26,3.219 4.26,3.219 4.427,3.219 true 6.542,3.188 6.542,3.615 6.542,3.615 6.708,3.615 true 4.479,2.521 5.094,2.719 0.615,0.198 10 false CANH 4.458,3.156 5.073,3.354 0.615,0.198 10 false CANL 1.281,2.417 1.896,2.615 0.615,0.198 10 false N121*B 1.281,2.167 1.896,2.365 0.615,0.198 10 false N120*B 2.917,2.198 3.531,2.396 0.615,0.198 10 false *a 0.146,0.083 0.76,0.281 0.615,0.198 10 false *1 1.271,2.656 1.885,2.854 0.615,0.198 10 false N177*B 1.271,2.885 1.885,3.083 0.615,0.198 10 false N120*A 1.26,1.917 1.875,2.115 0.615,0.198 10 false N119*B 1.271,1.667 1.885,1.865 0.615,0.198 10 false N118*B 1.813,2.646 2.427,2.844 0.615,0.198 10 false N121*A 5.083,1.875 5.698,2.073 0.615,0.198 10 false *b 5.958,2.167 6.271,2.365 0.313,0.198 10 false N8 6.781,3.531 7.156,3.74 0.375,0.208 10 false BAT 1.271,3.135 1.885,3.333 0.615,0.198 10 false N119*A 1.271,3.385 1.885,3.583 0.615,0.198 10 false N118*A 1.802,2.396 2.417,2.594 0.615,0.198 10 false N123*A 1.802,2.156 2.417,2.354 0.615,0.198 10 false N177*A
*A for RHD *B for LHD
*1 No. 4 CAN Junction Connector - -
*a Rear view of wire harness connector
(to No. 4 CAN Junction Connector)
*b Front view of DLC3


Wiring Color
Code Color (CANH Side) Color (CANL Side) Connect to

*: w/ Tire Pressure Warning System (Tire Inflation Pressure Display Function)

N118 SB W Central gateway ECU (network gateway ECU)
N119 GR W Brake actuator assembly (skid control ECU)
N120 R W Airbag sensor assembly
N121 P W Steering sensor
N123 G W Power steering ECU assembly
N177 B W Tire pressure warning ECU and receiver*


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N123-1 (CANH) - N8-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
N123-2 (CANL) - N8-16 (BAT)



c.

Reconnect the N123 No. 4 CAN junction connector.


Result:
Proceed to
OK
NG



OK

58.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 4 CAN JUNCTION CONNECTOR - STEERING SENSOR)

NG

61.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (POWER STEERING ECU ASSEMBLY - NO. 4 CAN JUNCTION CONNECTOR)
58.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 4 CAN JUNCTION CONNECTOR - STEERING SENSOR)
a.

Disconnect the N121 No. 4 CAN junction connector.

HINT:
·

Before disconnecting the connectors, make a note of where it is connected.

·

Reconnect the connector to its original position.



C414819C03
5.823,2.104 6.25,2.354 0.427,0.25 3.927,2.833 4.281,2.573 4.281,2.573 4.448,2.573 true 3.927,2.99 4.26,3.219 4.26,3.219 4.427,3.219 true 6.542,3.188 6.542,3.615 6.542,3.615 6.708,3.615 true 4.479,2.521 5.094,2.719 0.615,0.198 10 false CANH 4.458,3.156 5.073,3.354 0.615,0.198 10 false CANL 1.281,2.417 1.896,2.615 0.615,0.198 10 false N121*B 1.281,2.167 1.896,2.365 0.615,0.198 10 false N120*B 2.917,2.198 3.531,2.396 0.615,0.198 10 false *a 0.146,0.083 0.76,0.281 0.615,0.198 10 false *1 1.271,2.656 1.885,2.854 0.615,0.198 10 false N177*B 1.271,2.885 1.885,3.083 0.615,0.198 10 false N120*A 1.26,1.917 1.875,2.115 0.615,0.198 10 false N119*B 1.271,1.667 1.885,1.865 0.615,0.198 10 false N118*B 1.813,2.646 2.427,2.844 0.615,0.198 10 false N121*A 5.083,1.875 5.698,2.073 0.615,0.198 10 false *b 5.958,2.167 6.271,2.365 0.313,0.198 10 false N8 6.781,3.531 7.156,3.74 0.375,0.208 10 false BAT 1.271,3.135 1.885,3.333 0.615,0.198 10 false N119*A 1.271,3.385 1.885,3.583 0.615,0.198 10 false N118*A 1.802,2.396 2.417,2.594 0.615,0.198 10 false N123*A 1.802,2.156 2.417,2.354 0.615,0.198 10 false N177*A
*A for RHD *B for LHD
*1 No. 4 CAN Junction Connector - -
*a Rear view of wire harness connector
(to No. 4 CAN Junction Connector)
*b Front view of DLC3


Wiring Color
Code Color (CANH Side) Color (CANL Side) Connect to

*1: w/ Variable Flow Control Solenoid Valve

*2: w/ Tire Pressure Warning System (Tire Inflation Pressure Display Function)

N118 SB W Central gateway ECU (network gateway ECU)
N119 GR W Brake actuator assembly (skid control ECU)
N120 R W Airbag sensor assembly
N121 P W Steering sensor
N123 G W Power steering ECU assembly*1
N177 B W Tire pressure warning ECU and receiver*2


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N121-1 (CANH) - N8-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
N121-2 (CANL) - N8-16 (BAT)



c.

Reconnect the N121 No. 4 CAN junction connector.


Result:
Proceed to
OK
NG



OK

59.CHECK VEHICLE TYPE

NG

62.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (STEERING SENSOR - NO. 4 CAN JUNCTION CONNECTOR)
59.CHECK VEHICLE TYPE
a.

Check for vehicle type.


Result:
Result Proceed to
w/o Tire Pressure Warning System (Tire Inflation Pressure Display Function) A
w/ Tire Pressure Warning System (Tire Inflation Pressure Display Function) B



A

REPLACE NO. 4 CAN JUNCTION CONNECTOR

B

63.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 4 CAN JUNCTION CONNECTOR - TIRE PRESSURE WARNING ECU AND RECEIVER)
60.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (BRAKE ACTUATOR ASSEMBLY [SKID CONTROL ECU] - NO. 4 CAN JUNCTION CONNECTOR)
a.
C414351C02
1.479,0.313 1.927,0.573 0.448,0.26 1.479,2.677 1.927,2.938 0.448,0.26 2.615,4.354 2.479,4.354 2.479,4.354 2.354,3.948 true 1.313,2.198 1.177,2.198 1.177,2.198 0.99,1.583 true 1.229,0.823 1.094,0.823 1.094,0.823 0.896,1.281 true 0.094,0.073 0.427,0.396 0.333,0.323 10 false *a 0.094,2.594 0.5,2.938 0.406,0.344 10 false *b 1.583,0.365 2.042,0.563 0.458,0.198 10 false A28 1.625,2.74 2.083,2.938 0.458,0.198 10 false N8 2.656,4.26 2.969,4.458 0.313,0.198 10 false BAT 1.354,2.115 1.969,2.313 0.615,0.198 10 false CANL 1.26,0.729 1.875,0.927 0.615,0.198 10 false CANH
*a Front view of wire harness connector
(to Brake Actuator Assembly [Skid Control ECU])
*b Front view of DLC3


Disconnect the A28 brake actuator assembly (skid control ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A28-26 (CANH) - N8-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
A28-14 (CANL) - N8-16 (BAT)



c.

Reconnect the A28 brake actuator assembly (skid control ECU) connector.


Result:
Proceed to
OK
NG



OK

REPLACE BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU)

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (BRAKE ACTUATOR ASSEMBLY [SKID CONTROL ECU] - NO. 4 CAN JUNCTION CONNECTOR)

61.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (POWER STEERING ECU ASSEMBLY - NO. 4 CAN JUNCTION CONNECTOR)
a.
C379614C06
0.24,0.99 0.594,1.188 0.354,0.198 0.167,2.333 0.521,2.531 0.354,0.198 0.833,1.792 1.021,1.792 1.021,1.792 1.125,1.271 true 1.542,0.333 1.375,0.333 1.375,0.333 1.302,1.135 true 2.573,3.104 2.406,3.104 2.406,3.104 2.208,2.604 true 0.354,0.135 0.667,0.333 0.313,0.198 10 false *a 0.427,1.729 0.938,1.938 0.51,0.208 10 false CANH 1.583,0.26 2.094,0.469 0.51,0.208 10 false CANL 0.292,1.01 0.802,1.219 0.51,0.208 10 false N36 0.24,2.354 0.75,2.563 0.51,0.208 10 false N8 2.625,3.021 3.135,3.229 0.51,0.208 10 false BAT 0.25,2.01 0.563,2.208 0.313,0.198 10 false *b
*a Front view of wire harness connector
(to Power Steering ECU Assembly)
*b Front view of DLC3


Disconnect the N36 power steering ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N36-1 (CANH) - N8-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
N36-2 (CANL) - N8-16 (BAT)



c.

Reconnect the N36 power steering ECU assembly connector.


Result:
Proceed to
OK
NG



OK

REPLACE POWER STEERING ECU ASSEMBLY

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (POWER STEERING ECU ASSEMBLY - NO. 4 CAN JUNCTION CONNECTOR)

62.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (STEERING SENSOR - NO. 4 CAN JUNCTION CONNECTOR)
a.
C414352C02
0.427,0.865 0.865,1.104 0.438,0.24 0.188,2.542 0.625,2.781 0.438,0.24 2.354,2.844 2.479,3.24 2.479,3.24 2.604,3.24 true 1.719,1.271 1.833,1.75 1.833,1.75 1.958,1.75 true 1.708,0.948 1.833,0.229 1.833,0.229 1.958,0.229 true 0.573,0.906 0.875,1.104 0.302,0.198 10 false N3 1.99,0.146 2.448,0.344 0.458,0.198 10 false CANH 2,1.667 2.458,1.865 0.458,0.198 10 false CANL 2.656,3.156 3.115,3.354 0.458,0.198 10 false BAT 0.323,2.583 0.625,2.781 0.302,0.198 10 false N8 0.146,0.104 0.458,0.302 0.313,0.198 10 false *a 0.146,1.823 0.698,2.115 0.552,0.292 10 false *b
*a Front view of wire harness connector
(to Steering Sensor)
*b Front view of DLC3


Disconnect the N3 steering sensor connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N3-3 (CANH) - N8-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
N3-8 (CANL) - N8-16 (BAT)



c.

Reconnect the N3 steering sensor connector.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (STEERING SENSOR - NO. 4 CAN JUNCTION CONNECTOR)

63.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 4 CAN JUNCTION CONNECTOR - TIRE PRESSURE WARNING ECU AND RECEIVER)
a.

Disconnect the N177 No. 4 CAN junction connector.

HINT:
·

Before disconnecting the connectors, make a note of where it is connected.

·

Reconnect the connector to its original position.



C414819C03
5.823,2.104 6.25,2.354 0.427,0.25 3.927,2.833 4.281,2.573 4.281,2.573 4.448,2.573 true 3.927,2.99 4.26,3.219 4.26,3.219 4.427,3.219 true 6.542,3.188 6.542,3.615 6.542,3.615 6.708,3.615 true 4.479,2.521 5.094,2.719 0.615,0.198 10 false CANH 4.458,3.156 5.073,3.354 0.615,0.198 10 false CANL 1.281,2.417 1.896,2.615 0.615,0.198 10 false N121*B 1.281,2.167 1.896,2.365 0.615,0.198 10 false N120*B 2.917,2.198 3.531,2.396 0.615,0.198 10 false *a 0.146,0.083 0.76,0.281 0.615,0.198 10 false *1 1.271,2.656 1.885,2.854 0.615,0.198 10 false N177*B 1.271,2.885 1.885,3.083 0.615,0.198 10 false N120*A 1.26,1.917 1.875,2.115 0.615,0.198 10 false N119*B 1.271,1.667 1.885,1.865 0.615,0.198 10 false N118*B 1.813,2.646 2.427,2.844 0.615,0.198 10 false N121*A 5.083,1.875 5.698,2.073 0.615,0.198 10 false *b 5.958,2.167 6.271,2.365 0.313,0.198 10 false N8 6.781,3.531 7.156,3.74 0.375,0.208 10 false BAT 1.271,3.135 1.885,3.333 0.615,0.198 10 false N119*A 1.271,3.385 1.885,3.583 0.615,0.198 10 false N118*A 1.802,2.396 2.417,2.594 0.615,0.198 10 false N123*A 1.802,2.156 2.417,2.354 0.615,0.198 10 false N177*A
*A for RHD *B for LHD
*1 No. 4 CAN Junction Connector - -
*a Rear view of wire harness connector
(to No. 4 CAN Junction Connector)
*b Front view of DLC3


Wiring Color
Code Color (CANH Side) Color (CANL Side) Connect to

*: w/ Variable Flow Control Solenoid Valve

N118 SB W Central gateway ECU (network gateway ECU)
N119 GR W Brake actuator assembly (skid control ECU)
N120 R W Airbag sensor assembly
N121 P W Steering sensor
N123 G W Power steering ECU assembly*
N177 B W Tire pressure warning ECU and receiver


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N177-1 (CANH) - N8-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
N177-2 (CANL) - N8-16 (BAT)



c.

Reconnect the N177 No. 4 CAN junction connector.


Result:
Proceed to
OK
NG



OK

REPLACE NO. 4 CAN JUNCTION CONNECTOR

NG

64.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (TIRE PRESSURE WARNING ECU AND RECEIVER - NO. 4 CAN JUNCTION CONNECTOR)
64.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (TIRE PRESSURE WARNING ECU AND RECEIVER - NO. 4 CAN JUNCTION CONNECTOR)
a.
C414820C02
1.5,0.104 1.917,0.354 0.417,0.25 0.208,2.365 0.625,2.615 0.417,0.25 1.25,1.521 1.417,1.521 1.417,1.521 1.615,1.198 true 1.333,1.656 1.5,1.656 1.5,1.656 1.771,1.198 true 2.302,2.75 2.552,3.125 2.552,3.125 2.719,3.125 true 0.125,0.104 0.438,0.302 0.313,0.198 10 false *a 1.646,0.156 1.958,0.354 0.313,0.198 10 false Z3 0.844,1.427 1.26,1.615 0.417,0.188 10 false CANH 0.958,1.594 1.375,1.781 0.417,0.188 10 false CANL 2.875,3.063 3.271,3.26 0.396,0.198 10 false BAT 0.333,2.406 0.646,2.604 0.313,0.198 10 false N8 0.167,1.948 0.479,2.146 0.313,0.198 10 false *b
*a Front view of wire harness connector
(to Tire Pressure Warning ECU and Receiver)
*b Front view of DLC3


Disconnect the Z3 tire pressure warning ECU and receiver connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Z3-9 (CANH) - N8-16 (BAT) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
Z3-10 (CANL) - N8-16 (BAT)



c.

Reconnect the Z3 tire pressure warning ECU and receiver connector.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (TIRE PRESSURE WARNING ECU AND RECEIVER - NO. 4 CAN JUNCTION CONNECTOR)

65.CHECK FOR SHORT IN CAN BUS WIRES (CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU] - NO. 4 CAN JUNCTION CONNECTOR)
a.
C368242C46
1.417,0.24 1.958,0.458 0.542,0.219 2.24,1.135 2.365,0.573 2.365,0.573 2.125,0.573 true 2.073,1.792 2.271,1.792 2.271,1.792 2.146,1.292 true 1.573,0.281 2.031,0.479 0.458,0.198 10 false N21 1.719,0.5 2.177,0.698 0.458,0.198 10 false CA2L 1.677,1.708 2.156,1.906 0.479,0.198 10 false CA2H 0.073,0.052 0.531,0.25 0.458,0.198 10 false *a
*a Front view of wire harness connector
(to Central Gateway ECU [Network Gateway ECU])


Disconnect the N21 central gateway ECU (network gateway ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N21-22 (CA2H) - N21-7 (CA2L) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



c.

Reconnect the N21 central gateway ECU (network gateway ECU) connector.


Result:
Proceed to
OK
NG



OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

66.CHECK VEHICLE TYPE
66.CHECK VEHICLE TYPE
a.

Check for vehicle type.


Result:
Result Proceed to
w/ Airbag System A
w/o Airbag System B



A

67.CHECK FOR SHORT IN CAN BUS WIRES (AIRBAG SENSOR ASSEMBLY - NO. 4 CAN JUNCTION CONNECTOR)

B

68.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 CAN JUNCTION TERMINAL - NO. 4 CAN JUNCTION CONNECTOR)
67.CHECK FOR SHORT IN CAN BUS WIRES (AIRBAG SENSOR ASSEMBLY - NO. 4 CAN JUNCTION CONNECTOR)
a.
C414353C01
1.5,0.26 1.938,0.49 0.438,0.229 2.25,1.854 2.583,1.563 2.583,1.563 2.719,1.563 true 2.115,1.865 2.583,1.125 2.583,1.125 2.719,1.125 true 1.604,0.292 2.063,0.49 0.458,0.198 10 false N45 2.781,1.479 3.396,1.677 0.615,0.198 10 false CANL 2.781,1.052 3.396,1.25 0.615,0.198 10 false CANH 0.094,0.083 0.708,0.281 0.615,0.198 10 false *a
*a Front view of wire harness connector
(to Airbag Sensor Assembly)


Disconnect the N45 airbag sensor assembly connector.

for Type A: Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for Type A)>PRECAUTION

for Type B: Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for Type B)>PRECAUTION

for Type C: Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for Type C)>PRECAUTION


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N45-26 (CANH) - N45-27 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



c.

Reconnect the N45 airbag sensor assembly connector.


Result:
Proceed to
OK
NG



OK

NG

69.CHECK VEHICLE TYPE
68.CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 CAN JUNCTION TERMINAL - NO. 4 CAN JUNCTION CONNECTOR)
a.
C369111C30
1.5,0.333 1.917,0.583 0.417,0.25 1.729,1.135 1.563,0.667 1.563,0.667 1.417,0.667 true 1.948,1.146 2.073,0.667 2.073,0.667 2.24,0.667 true 0.073,0.052 0.385,0.25 0.313,0.198 10 false *a 1.552,0.375 2,0.583 0.448,0.208 10 false N122 2.281,0.604 2.771,0.865 0.49,0.26 10 false CANH 0.99,0.594 1.479,0.854 0.49,0.26 10 false CANL
*a Front view of wire harness connector
(to No. 2 CAN Junction Terminal)


Disconnect the N122 No. 2 CAN junction terminal connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N122-3 (CANH) - N122-2 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



c.

Reconnect the N122 No. 2 CAN junction terminal connector.


Result:
Proceed to
OK
NG



OK

REPLACE NO. 2 CAN JUNCTION TERMINAL

NG

77.CHECK FOR SHORT IN CAN BUS WIRES (NO. 4 CAN JUNCTION CONNECTOR - NO. 2 CAN JUNCTION TERMINAL)
69.CHECK VEHICLE TYPE
a.

Check for vehicle type.


Result:
Result Proceed to
except Wagon A
for Wagon B



A

70.CHECK FOR SHORT IN CAN BUS WIRES (NO. 4 CAN JUNCTION CONNECTOR - AIRBAG SENSOR ASSEMBLY)

B

83.CHECK FOR SHORT IN CAN BUS WIRES (NO. 4 CAN JUNCTION CONNECTOR - AIRBAG SENSOR ASSEMBLY)
70.CHECK FOR SHORT IN CAN BUS WIRES (NO. 4 CAN JUNCTION CONNECTOR - AIRBAG SENSOR ASSEMBLY)
a.

Disconnect the N120 No. 4 CAN junction connector.

HINT:
·

Before disconnecting the connectors, make a note of where it is connected.

·

Reconnect the connector to its original position.



C414494C01
5.25,2.833 5.604,2.573 5.604,2.573 5.771,2.573 true 5.26,2.99 5.594,3.219 5.594,3.219 5.76,3.219 true 5.833,2.521 6.448,2.719 0.615,0.198 10 false CANH 5.833,3.167 6.448,3.365 0.615,0.198 10 false CANL 2.063,2.427 2.677,2.625 0.615,0.198 10 false N121 2.063,2.177 2.677,2.375 0.615,0.198 10 false N120 4.229,2.198 4.844,2.396 0.615,0.198 10 false *a 0.146,0.083 0.76,0.281 0.615,0.198 10 false *1 2.063,2.677 2.677,2.875 0.615,0.198 10 false N123 2.063,1.948 2.677,2.146 0.615,0.198 10 false N119 2.063,1.667 2.677,1.865 0.615,0.198 10 false N118
*1 No. 4 CAN Junction Connector - -
*a Rear view of wire harness connector
(to No. 4 CAN Junction Connector)
- -


Wiring Color
Code Color (CANH Side) Color (CANL Side) Connect to

*1: w/ VSC OFF Switch

*2: w/o VSC OFF Switch

*3: w/ Variable Flow Control Solenoid Valve

N118 SB W Central gateway ECU (network gateway ECU)
N119 GR W Brake actuator assembly (skid control ECU)
N120 R W Airbag sensor assembly
N121 P W
·

Steering sensor*1

·

Combination switch ECU sub-assembly*2


N123 G W Power steering ECU assembly*3


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N120-1 (CANH) - N120-2 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



c.

Reconnect the N120 No. 4 CAN junction connector.


Result:
Proceed to
OK
NG



OK

71.CHECK FOR SHORT IN CAN BUS WIRES (NO. 4 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU])

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 4 CAN JUNCTION CONNECTOR - AIRBAG SENSOR ASSEMBLY)

71.CHECK FOR SHORT IN CAN BUS WIRES (NO. 4 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU])
a.

Disconnect the N118 No. 4 CAN junction connector.

HINT:
·

Before disconnecting the connectors, make a note of where it is connected.

·

Reconnect the connector to its original position.



C414203C01
5.25,2.833 5.604,2.573 5.604,2.573 5.771,2.573 true 5.26,2.99 5.594,3.219 5.594,3.219 5.76,3.219 true 5.833,2.521 6.448,2.719 0.615,0.198 10 false CANH 5.833,3.167 6.448,3.365 0.615,0.198 10 false CANL 2.063,2.427 2.677,2.625 0.615,0.198 10 false N121 2.063,2.177 2.677,2.375 0.615,0.198 10 false N120 4.229,2.198 4.844,2.396 0.615,0.198 10 false *a 0.146,0.083 0.76,0.281 0.615,0.198 10 false *1 2.063,2.677 2.677,2.875 0.615,0.198 10 false N123*A 2.073,2.917 2.688,3.115 0.615,0.198 10 false N124*A 2.063,1.948 2.677,2.146 0.615,0.198 10 false N119 2.063,1.667 2.677,1.865 0.615,0.198 10 false N118 2.604,2.677 3.219,2.875 0.615,0.198 10 false N124*B
*A for RHD *B for LHD
*1 No. 4 CAN Junction Connector - -
*a Rear view of wire harness connector
(to No. 4 CAN Junction Connector)
- -


Wiring Color
Code Color (CANH Side) Color (CANL Side) Connect to

*1: w/ Airbag System

*2: w/ VSC OFF Switch

*3: w/o VSC OFF Switch

*4: w/ Variable Flow Control Solenoid Valve

*5: w/o Airbag System

N118 SB W Central gateway ECU (network gateway ECU)
N119 GR W Brake actuator assembly (skid control ECU)
N120 R W Airbag sensor assembly*1
N121 P W
·

Steering sensor*2

·

Combination switch ECU sub-assembly*3


N123 G W Power steering ECU assembly*4
N124 L W No. 2 CAN junction terminal*5


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N118-1 (CANH) - N118-2 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



c.

Reconnect the N118 No. 4 CAN junction connector.


Result:
Proceed to
OK
NG



OK

72.CHECK FOR SHORT IN CAN BUS WIRES (NO. 4 CAN JUNCTION CONNECTOR - BRAKE ACTUATOR ASSEMBLY [SKID CONTROL ECU])

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 4 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU])

72.CHECK FOR SHORT IN CAN BUS WIRES (NO. 4 CAN JUNCTION CONNECTOR - BRAKE ACTUATOR ASSEMBLY [SKID CONTROL ECU])
a.

Disconnect the N119 No. 4 CAN junction connector.

HINT:
·

Before disconnecting the connectors, make a note of where it is connected.

·

Reconnect the connector to its original position.



C414203C01
5.25,2.833 5.604,2.573 5.604,2.573 5.771,2.573 true 5.26,2.99 5.594,3.219 5.594,3.219 5.76,3.219 true 5.833,2.521 6.448,2.719 0.615,0.198 10 false CANH 5.833,3.167 6.448,3.365 0.615,0.198 10 false CANL 2.063,2.427 2.677,2.625 0.615,0.198 10 false N121 2.063,2.177 2.677,2.375 0.615,0.198 10 false N120 4.229,2.198 4.844,2.396 0.615,0.198 10 false *a 0.146,0.083 0.76,0.281 0.615,0.198 10 false *1 2.063,2.677 2.677,2.875 0.615,0.198 10 false N123*A 2.073,2.917 2.688,3.115 0.615,0.198 10 false N124*A 2.063,1.948 2.677,2.146 0.615,0.198 10 false N119 2.063,1.667 2.677,1.865 0.615,0.198 10 false N118 2.604,2.677 3.219,2.875 0.615,0.198 10 false N124*B
*A for RHD *B for LHD
*1 No. 4 CAN Junction Connector - -
*a Rear view of wire harness connector
(to No. 4 CAN Junction Connector)
- -


Wiring Color
Code Color (CANH Side) Color (CANL Side) Connect to

*1: w/ Airbag System

*2: w/ VSC OFF Switch

*3: w/o VSC OFF Switch

*4: w/ Variable Flow Control Solenoid Valve

*5: w/o Airbag System

N118 SB W Central gateway ECU (network gateway ECU)
N119 GR W Brake actuator assembly (skid control ECU)
N120 R W Airbag sensor assembly*1
N121 P W
·

Steering sensor*2

·

Combination switch ECU sub-assembly*3


N123 G W Power steering ECU assembly*4
N124 L W No. 2 CAN junction terminal*5


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N119-1 (CANH) - N119-2 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher



c.

Reconnect the N119 No. 4 CAN junction connector.


Result:
Proceed to
OK
NG



OK

73.CHECK VEHICLE TYPE

NG

78.CHECK FOR SHORT IN CAN BUS WIRES (BRAKE ACTUATOR ASSEMBLY [SKID CONTROL ECU] - NO. 4 CAN JUNCTION CONNECTOR)
73.CHECK VEHICLE TYPE
a.

Check for vehicle type.


Result:
Result Proceed to
w/ Variable Flow Control Solenoid Valve A
w/o Variable Flow Control Solenoid Valve B



A

74.CHECK FOR SHORT IN CAN BUS WIRES (NO. 4 CAN JUNCTION CONNECTOR - POWER STEERING ECU ASSEMBLY)

B

75.CHECK VEHICLE TYPE
74.CHECK FOR SHORT IN CAN BUS WIRES (NO. 4 CAN JUNCTION CONNECTOR - POWER STEERING ECU ASSEMBLY)
a.

Disconnect the N123 No. 4 CAN junction connector.

HINT:
·

Before disconnecting the connectors, make a note of where it is connected.

·

Reconnect the connector to its original position.



C414495C01
5.25,2.833 5.604,2.573 5.604,2.573 5.771,2.573 true 5.26,2.99 5.594,3.219 5.594,3.219 5.76,3.219 true 5.833,2.521 6.448,2.719 0.615,0.198 10 false CANH 5.833,3.167 6.448,3.365 0.615,0.198 10 false CANL 2.063,2.427 2.677,2.625 0.615,0.198 10 false N121 2.063,2.177 2.677,2.375 0.615,0.198 10 false N120 4.229,2.198 4.844,2.396 0.615,0.198 10 false *a 0.146,0.083 0.76,0.281 0.615,0.198 10 false *1 2.063,2.677 2.677,2.875 0.615,0.198 10 false N123 2.073,2.917 2.688,3.115 0.615,0.198 10 false N124 2.063,1.948 2.677,2.146 0.615,0.198 10 false N119 2.063,1.667 2.677,1.865 0.615,0.198 10 false N118
*1 No. 4 CAN Junction Connector - -
*a Rear view of wire harness connector
(to No. 4 CAN Junction Connector)
- -


Wiring Color
Code Color (CANH Side) Color (CANL Side) Connect to

*1: w/ Airbag System

*2: w/ VSC OFF Switch

*3: w/o VSC OFF Switch

*4: w/o Airbag System

N118 SB W Central gateway ECU (network gateway ECU)
N119 GR W Brake actuator assembly (skid control ECU)
N120 R W Airbag sensor assembly*1
N121 P W
·

Steering sensor*2

·

Combination switch ECU sub-assembly*3


N123 G W Power steering ECU assembly
N124 L W No. 2 CAN junction terminal*4


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N123-1 (CANH) - N123-2 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher



c.

Reconnect the N123 No. 4 CAN junction connector.


Result:
Proceed to
OK
NG



OK

75.CHECK VEHICLE TYPE

NG

79.CHECK FOR SHORT IN CAN BUS WIRES (POWER STEERING ECU ASSEMBLY - NO. 4 CAN JUNCTION CONNECTOR)
75.CHECK VEHICLE TYPE
a.

Check for vehicle type.


Result:
Result Proceed to
w/ VSC OFF Switch A
w/o VSC OFF Switch B



A

76.CHECK FOR SHORT IN CAN BUS WIRES (NO. 4 CAN JUNCTION CONNECTOR - STEERING SENSOR)

B

80.CHECK FOR SHORT IN CAN BUS WIRES (NO. 4 CAN JUNCTION CONNECTOR - COMBINATION SWITCH ECU SUB-ASSEMBLY)
76.CHECK FOR SHORT IN CAN BUS WIRES (NO. 4 CAN JUNCTION CONNECTOR - STEERING SENSOR)
a.

Disconnect the N121 No. 4 CAN junction connector.

HINT:
·

Before disconnecting the connectors, make a note of where it is connected.

·

Reconnect the connector to its original position.



C414203C01
5.25,2.833 5.604,2.573 5.604,2.573 5.771,2.573 true 5.26,2.99 5.594,3.219 5.594,3.219 5.76,3.219 true 5.833,2.521 6.448,2.719 0.615,0.198 10 false CANH 5.833,3.167 6.448,3.365 0.615,0.198 10 false CANL 2.063,2.427 2.677,2.625 0.615,0.198 10 false N121 2.063,2.177 2.677,2.375 0.615,0.198 10 false N120 4.229,2.198 4.844,2.396 0.615,0.198 10 false *a 0.146,0.083 0.76,0.281 0.615,0.198 10 false *1 2.063,2.677 2.677,2.875 0.615,0.198 10 false N123*A 2.073,2.917 2.688,3.115 0.615,0.198 10 false N124*A 2.063,1.948 2.677,2.146 0.615,0.198 10 false N119 2.063,1.667 2.677,1.865 0.615,0.198 10 false N118 2.604,2.677 3.219,2.875 0.615,0.198 10 false N124*B
*A for RHD *B for LHD
*1 No. 4 CAN Junction Connector - -
*a Rear view of wire harness connector
(to No. 4 CAN Junction Connector)
- -


Wiring Color
Code Color (CANH Side) Color (CANL Side) Connect to

*1: w/ Airbag System

*2: w/ Variable Flow Control Solenoid Valve

*3: w/o Airbag System

N118 SB W Central gateway ECU (network gateway ECU)
N119 GR W Brake actuator assembly (skid control ECU)
N120 R W Airbag sensor assembly*1
N121 P W Steering sensor
N123 G W Power steering ECU assembly*2
N124 L W No. 2 CAN junction terminal*3


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N121-1 (CANH) - N121-2 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher



c.

Reconnect the N121 No. 4 CAN junction connector.


Result:
Proceed to
OK
NG



OK

REPLACE NO. 4 CAN JUNCTION CONNECTOR

NG

81.CHECK FOR SHORT IN CAN BUS WIRES (STEERING SENSOR - NO. 4 CAN JUNCTION CONNECTOR)
77.CHECK FOR SHORT IN CAN BUS WIRES (NO. 4 CAN JUNCTION CONNECTOR - NO. 2 CAN JUNCTION TERMINAL)
a.

Disconnect the N124 No. 4 CAN junction connector.

HINT:
·

Before disconnecting the connectors, make a note of where it is connected.

·

Reconnect the connector to its original position.



C414493C01
5.25,2.833 5.604,2.573 5.604,2.573 5.771,2.573 true 5.26,2.99 5.594,3.219 5.594,3.219 5.76,3.219 true 5.833,2.521 6.448,2.719 0.615,0.198 10 false CANH 5.833,3.167 6.448,3.365 0.615,0.198 10 false CANL 2.063,2.427 2.677,2.625 0.615,0.198 10 false N121 4.229,2.198 4.844,2.396 0.615,0.198 10 false *a 0.146,0.083 0.76,0.281 0.615,0.198 10 false *1 2.063,2.677 2.677,2.875 0.615,0.198 10 false N123*A 2.073,2.917 2.688,3.115 0.615,0.198 10 false N124*A 2.063,1.948 2.677,2.146 0.615,0.198 10 false N119 2.063,1.667 2.677,1.865 0.615,0.198 10 false N118 2.604,2.677 3.219,2.875 0.615,0.198 10 false N124*B
*A for RHD *B for LHD
*1 No. 4 CAN Junction Connector - -
*a Rear view of wire harness connector
(to No. 4 CAN Junction Connector)
- -


Wiring Color
Code Color (CANH Side) Color (CANL Side) Connect to

*1: w/ VSC OFF Switch

*2: w/o VSC OFF Switch

*3: w/ Variable Flow Control Solenoid Valve

N118 SB W Central gateway ECU (network gateway ECU)
N119 GR W Brake actuator assembly (skid control ECU)
N121 P W
·

Steering sensor*1

·

Combination switch ECU sub-assembly*2


N123 G W Power steering ECU assembly*3
N124 L W No. 2 CAN junction terminal


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N124-1 (CANH) - N124-2 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



c.

Reconnect the N124 No. 4 CAN junction connector.


Result:
Proceed to
OK
NG



OK

71.CHECK FOR SHORT IN CAN BUS WIRES (NO. 4 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU])

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 4 CAN JUNCTION CONNECTOR - NO. 2 CAN JUNCTION TERMINAL)

78.CHECK FOR SHORT IN CAN BUS WIRES (BRAKE ACTUATOR ASSEMBLY [SKID CONTROL ECU] - NO. 4 CAN JUNCTION CONNECTOR)
a.
C414214C04
1.5,0.24 1.948,0.521 0.448,0.281 0.646,0.969 0.813,0.969 0.813,0.969 0.813,1.469 true 1.24,2.479 1.031,2.479 1.031,2.479 0.875,1.823 true 1.604,0.313 2.063,0.51 0.458,0.198 10 false A28 0.094,0.115 0.552,0.313 0.458,0.198 10 false *a 0.24,0.906 0.698,1.104 0.458,0.198 10 false CANH 1.313,2.406 1.771,2.604 0.458,0.198 10 false CANL
*a Front view of wire harness connector
(to Brake Actuator Assembly [Skid Control ECU])


Disconnect the A28 brake actuator assembly (skid control ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A28-26 (CANH) - A28-14 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



c.

Reconnect the A28 brake actuator assembly (skid control ECU) connector.


Result:
Proceed to
OK
NG



OK

REPLACE BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU)

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (BRAKE ACTUATOR ASSEMBLY [SKID CONTROL ECU] - NO. 4 CAN JUNCTION CONNECTOR)

79.CHECK FOR SHORT IN CAN BUS WIRES (POWER STEERING ECU ASSEMBLY - NO. 4 CAN JUNCTION CONNECTOR)
a.
C414354C01
1.49,0.219 1.948,0.469 0.458,0.25 0.792,1.677 0.938,1.677 0.938,1.677 1.125,1.302 true 1.594,1.688 1.438,1.688 1.438,1.688 1.292,1.292 true 1.594,0.26 2.052,0.458 0.458,0.198 10 false N36 0.167,0.115 0.625,0.313 0.458,0.198 10 false *a 0.365,1.604 0.979,1.802 0.615,0.198 10 false CANH 1.625,1.604 2.24,1.802 0.615,0.198 10 false CANL
*a Front view of wire harness connector
(to Power Steering ECU Assembly)


Disconnect the N36 power steering ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N36-1 (CANH) - N36-2 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



c.

Reconnect the N36 power steering ECU assembly connector.


Result:
Proceed to
OK
NG



OK

REPLACE POWER STEERING ECU ASSEMBLY

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (POWER STEERING ECU ASSEMBLY - NO. 4 CAN JUNCTION CONNECTOR)

80.CHECK FOR SHORT IN CAN BUS WIRES (NO. 4 CAN JUNCTION CONNECTOR - COMBINATION SWITCH ECU SUB-ASSEMBLY)
a.

Disconnect the N121 No. 4 CAN junction connector.

HINT:
·

Before disconnecting the connectors, make a note of where it is connected.

·

Reconnect the connector to its original position.



C414203C01
5.25,2.833 5.604,2.573 5.604,2.573 5.771,2.573 true 5.26,2.99 5.594,3.219 5.594,3.219 5.76,3.219 true 5.833,2.521 6.448,2.719 0.615,0.198 10 false CANH 5.833,3.167 6.448,3.365 0.615,0.198 10 false CANL 2.063,2.427 2.677,2.625 0.615,0.198 10 false N121 2.063,2.177 2.677,2.375 0.615,0.198 10 false N120 4.229,2.198 4.844,2.396 0.615,0.198 10 false *a 0.146,0.083 0.76,0.281 0.615,0.198 10 false *1 2.063,2.677 2.677,2.875 0.615,0.198 10 false N123*A 2.073,2.917 2.688,3.115 0.615,0.198 10 false N124*A 2.063,1.948 2.677,2.146 0.615,0.198 10 false N119 2.063,1.667 2.677,1.865 0.615,0.198 10 false N118 2.604,2.677 3.219,2.875 0.615,0.198 10 false N124*B
*A for RHD *B for LHD
*1 No. 4 CAN Junction Connector - -
*a Rear view of wire harness connector
(to No. 4 CAN Junction Connector)
- -


Wiring Color
Code Color (CANH Side) Color (CANL Side) Connect to

*1: w/ Airbag System

*2: w/ Variable Flow Control Solenoid Valve

*3: w/o Airbag System

N118 SB W Central gateway ECU (network gateway ECU)
N119 GR W Brake actuator assembly (skid control ECU)
N120 R W Airbag sensor assembly*1
N121 P W Combination switch ECU sub-assembly
N123 G W Power steering ECU assembly*2
N124 L W No. 2 CAN junction terminal*3


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N121-1 (CANH) - N121-2 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher



c.

Reconnect the N121 No. 4 CAN junction connector.


Result:
Proceed to
OK
NG



OK

REPLACE NO. 4 CAN JUNCTION CONNECTOR

NG

82.CHECK FOR SHORT IN CAN BUS WIRES (COMBINATION SWITCH ECU SUB-ASSEMBLY - NO. 4 CAN JUNCTION CONNECTOR)
81.CHECK FOR SHORT IN CAN BUS WIRES (STEERING SENSOR - NO. 4 CAN JUNCTION CONNECTOR)
a.
C369124C70
0.552,1.615 1.073,1.865 0.521,0.25 1,0.75 1.25,0.75 1.25,0.75 1.667,1.75 true 1.083,2.667 1.333,2.667 1.333,2.667 1.667,2 true 0.146,0.156 0.458,0.354 0.313,0.198 10 false *a 0.719,1.667 1.146,1.875 0.427,0.208 10 false N3 0.604,0.688 1.063,0.885 0.458,0.198 10 false CANH 0.708,2.594 1.167,2.792 0.458,0.198 10 false CANL
*a Front view of wire harness connector
(to Steering Sensor)


Disconnect the N3 steering sensor connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N3-3 (CANH) - N3-8 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



c.

Reconnect the N3 steering sensor connector.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (STEERING SENSOR - NO. 4 CAN JUNCTION CONNECTOR)

82.CHECK FOR SHORT IN CAN BUS WIRES (COMBINATION SWITCH ECU SUB-ASSEMBLY - NO. 4 CAN JUNCTION CONNECTOR)
a.
C369124C70
0.552,1.615 1.073,1.865 0.521,0.25 1,0.75 1.25,0.75 1.25,0.75 1.667,1.75 true 1.083,2.667 1.333,2.667 1.333,2.667 1.667,2 true 0.146,0.156 0.458,0.354 0.313,0.198 10 false *a 0.719,1.667 1.146,1.875 0.427,0.208 10 false N3 0.604,0.688 1.063,0.885 0.458,0.198 10 false CANH 0.708,2.594 1.167,2.792 0.458,0.198 10 false CANL
*a Front view of wire harness connector
(to Combination Switch ECU Sub-assembly)


Disconnect the N3 combination switch ECU sub-assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N3-3 (CANH) - N3-8 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



c.

Reconnect the N3 combination switch ECU sub-assembly connector.


Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION SWITCH ECU SUB-ASSEMBLY

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (COMBINATION SWITCH ECU SUB-ASSEMBLY - NO. 4 CAN JUNCTION CONNECTOR)

83.CHECK FOR SHORT IN CAN BUS WIRES (NO. 4 CAN JUNCTION CONNECTOR - AIRBAG SENSOR ASSEMBLY)
a.

Disconnect the N120 No. 4 CAN junction connector.

HINT:
·

Before disconnecting the connectors, make a note of where it is connected.

·

Reconnect the connector to its original position.



C414817C01
5.25,2.833 5.604,2.573 5.604,2.573 5.771,2.573 true 5.26,2.99 5.594,3.219 5.594,3.219 5.76,3.219 true 5.833,2.521 6.448,2.719 0.615,0.198 10 false CANH 5.833,3.167 6.448,3.365 0.615,0.198 10 false CANL 2.063,2.406 2.677,2.604 0.615,0.198 10 false N121*B 2.063,2.146 2.677,2.344 0.615,0.198 10 false N120*B 4.229,2.198 4.844,2.396 0.615,0.198 10 false *a 0.146,0.083 0.76,0.281 0.615,0.198 10 false *1 2.063,2.677 2.677,2.875 0.615,0.198 10 false N177*B 2.073,2.917 2.688,3.115 0.615,0.198 10 false N120*A 2.063,1.896 2.677,2.094 0.615,0.198 10 false N119*B 2.063,1.635 2.677,1.833 0.615,0.198 10 false N118*B 2.604,2.677 3.219,2.875 0.615,0.198 10 false N121*A 2.604,2.146 3.219,2.344 0.615,0.198 10 false N177*A 2.604,2.406 3.219,2.604 0.615,0.198 10 false N123*A 2.073,3.188 2.688,3.385 0.615,0.198 10 false N119*A 2.073,3.438 2.688,3.635 0.615,0.198 10 false N118*A
*A for RHD *B for LHD
*1 No. 4 CAN Junction Connector - -
*a Rear view of wire harness connector
(to No. 4 CAN Junction Connector)
- -


Wiring Color
Code Color (CANH Side) Color (CANL Side) Connect to

*1: w/ Variable Flow Control Solenoid Valve

*2: w/ Tire Pressure Warning System (Tire Inflation Pressure Display Function)

N118 SB W Central gateway ECU (network gateway ECU)
N119 GR W Brake actuator assembly (skid control ECU)
N120 R W Airbag sensor assembly
N121 P W Steering sensor
N123 G W Power steering ECU assembly*1
N177 B W Tire pressure warning ECU and receiver*2


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N120-1 (CANH) - N120-2 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



c.

Reconnect the N120 No. 4 CAN junction connector.


Result:
Proceed to
OK
NG



OK

84.CHECK FOR SHORT IN CAN BUS WIRES (NO. 4 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU])

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 4 CAN JUNCTION CONNECTOR - AIRBAG SENSOR ASSEMBLY)

84.CHECK FOR SHORT IN CAN BUS WIRES (NO. 4 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU])
a.

Disconnect the N118 No. 4 CAN junction connector.

HINT:
·

Before disconnecting the connectors, make a note of where it is connected.

·

Reconnect the connector to its original position.



C414817C01
5.25,2.833 5.604,2.573 5.604,2.573 5.771,2.573 true 5.26,2.99 5.594,3.219 5.594,3.219 5.76,3.219 true 5.833,2.521 6.448,2.719 0.615,0.198 10 false CANH 5.833,3.167 6.448,3.365 0.615,0.198 10 false CANL 2.063,2.406 2.677,2.604 0.615,0.198 10 false N121*B 2.063,2.146 2.677,2.344 0.615,0.198 10 false N120*B 4.229,2.198 4.844,2.396 0.615,0.198 10 false *a 0.146,0.083 0.76,0.281 0.615,0.198 10 false *1 2.063,2.677 2.677,2.875 0.615,0.198 10 false N177*B 2.073,2.917 2.688,3.115 0.615,0.198 10 false N120*A 2.063,1.896 2.677,2.094 0.615,0.198 10 false N119*B 2.063,1.635 2.677,1.833 0.615,0.198 10 false N118*B 2.604,2.677 3.219,2.875 0.615,0.198 10 false N121*A 2.604,2.146 3.219,2.344 0.615,0.198 10 false N177*A 2.604,2.406 3.219,2.604 0.615,0.198 10 false N123*A 2.073,3.188 2.688,3.385 0.615,0.198 10 false N119*A 2.073,3.438 2.688,3.635 0.615,0.198 10 false N118*A
*A for RHD *B for LHD
*1 No. 4 CAN Junction Connector - -
*a Rear view of wire harness connector
(to No. 4 CAN Junction Connector)
- -


Wiring Color
Code Color (CANH Side) Color (CANL Side) Connect to

*1: w/ Variable Flow Control Solenoid Valve

*2: w/ Tire Pressure Warning System (Tire Inflation Pressure Display Function)

N118 SB W Central gateway ECU (network gateway ECU)
N119 GR W Brake actuator assembly (skid control ECU)
N120 R W Airbag sensor assembly
N121 P W Steering sensor
N123 G W Power steering ECU assembly*1
N177 B W Tire pressure warning ECU and receiver*2


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N118-1 (CANH) - N118-2 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



c.

Reconnect the N118 No. 4 CAN junction connector.


Result:
Proceed to
OK
NG



OK

85.CHECK FOR SHORT IN CAN BUS WIRES (NO. 4 CAN JUNCTION CONNECTOR - BRAKE ACTUATOR ASSEMBLY [SKID CONTROL ECU])

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 4 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU])

85.CHECK FOR SHORT IN CAN BUS WIRES (NO. 4 CAN JUNCTION CONNECTOR - BRAKE ACTUATOR ASSEMBLY [SKID CONTROL ECU])
a.

Disconnect the N119 No. 4 CAN junction connector.

HINT:
·

Before disconnecting the connectors, make a note of where it is connected.

·

Reconnect the connector to its original position.



C414817C01
5.25,2.833 5.604,2.573 5.604,2.573 5.771,2.573 true 5.26,2.99 5.594,3.219 5.594,3.219 5.76,3.219 true 5.833,2.521 6.448,2.719 0.615,0.198 10 false CANH 5.833,3.167 6.448,3.365 0.615,0.198 10 false CANL 2.063,2.406 2.677,2.604 0.615,0.198 10 false N121*B 2.063,2.146 2.677,2.344 0.615,0.198 10 false N120*B 4.229,2.198 4.844,2.396 0.615,0.198 10 false *a 0.146,0.083 0.76,0.281 0.615,0.198 10 false *1 2.063,2.677 2.677,2.875 0.615,0.198 10 false N177*B 2.073,2.917 2.688,3.115 0.615,0.198 10 false N120*A 2.063,1.896 2.677,2.094 0.615,0.198 10 false N119*B 2.063,1.635 2.677,1.833 0.615,0.198 10 false N118*B 2.604,2.677 3.219,2.875 0.615,0.198 10 false N121*A 2.604,2.146 3.219,2.344 0.615,0.198 10 false N177*A 2.604,2.406 3.219,2.604 0.615,0.198 10 false N123*A 2.073,3.188 2.688,3.385 0.615,0.198 10 false N119*A 2.073,3.438 2.688,3.635 0.615,0.198 10 false N118*A
*A for RHD *B for LHD
*1 No. 4 CAN Junction Connector - -
*a Rear view of wire harness connector
(to No. 4 CAN Junction Connector)
- -


Wiring Color
Code Color (CANH Side) Color (CANL Side) Connect to

*1: w/ Variable Flow Control Solenoid Valve

*2: w/ Tire Pressure Warning System (Tire Inflation Pressure Display Function)

N118 SB W Central gateway ECU (network gateway ECU)
N119 GR W Brake actuator assembly (skid control ECU)
N120 R W Airbag sensor assembly
N121 P W Steering sensor
N123 G W Power steering ECU assembly*1
N177 B W Tire pressure warning ECU and receiver*2


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N119-1 (CANH) - N119-2 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher



c.

Reconnect the N119 No. 4 CAN junction connector.


Result:
Proceed to
OK
NG



OK

86.CHECK VEHICLE TYPE

NG

90.CHECK FOR SHORT IN CAN BUS WIRES (BRAKE ACTUATOR ASSEMBLY [SKID CONTROL ECU] - NO. 4 CAN JUNCTION CONNECTOR)
86.CHECK VEHICLE TYPE
a.

Check for vehicle type.


Result:
Result Proceed to
w/ Variable Flow Control Solenoid Valve A
w/o Variable Flow Control Solenoid Valve B



A

87.CHECK FOR SHORT IN CAN BUS WIRES (NO. 4 CAN JUNCTION CONNECTOR - POWER STEERING ECU ASSEMBLY)

B

88.CHECK FOR SHORT IN CAN BUS WIRES (NO. 4 CAN JUNCTION CONNECTOR - STEERING SENSOR)
87.CHECK FOR SHORT IN CAN BUS WIRES (NO. 4 CAN JUNCTION CONNECTOR - POWER STEERING ECU ASSEMBLY)
a.

Disconnect the N123 No. 4 CAN junction connector.

HINT:
·

Before disconnecting the connectors, make a note of where it is connected.

·

Reconnect the connector to its original position.



C414817C01
5.25,2.833 5.604,2.573 5.604,2.573 5.771,2.573 true 5.26,2.99 5.594,3.219 5.594,3.219 5.76,3.219 true 5.833,2.521 6.448,2.719 0.615,0.198 10 false CANH 5.833,3.167 6.448,3.365 0.615,0.198 10 false CANL 2.063,2.406 2.677,2.604 0.615,0.198 10 false N121*B 2.063,2.146 2.677,2.344 0.615,0.198 10 false N120*B 4.229,2.198 4.844,2.396 0.615,0.198 10 false *a 0.146,0.083 0.76,0.281 0.615,0.198 10 false *1 2.063,2.677 2.677,2.875 0.615,0.198 10 false N177*B 2.073,2.917 2.688,3.115 0.615,0.198 10 false N120*A 2.063,1.896 2.677,2.094 0.615,0.198 10 false N119*B 2.063,1.635 2.677,1.833 0.615,0.198 10 false N118*B 2.604,2.677 3.219,2.875 0.615,0.198 10 false N121*A 2.604,2.146 3.219,2.344 0.615,0.198 10 false N177*A 2.604,2.406 3.219,2.604 0.615,0.198 10 false N123*A 2.073,3.188 2.688,3.385 0.615,0.198 10 false N119*A 2.073,3.438 2.688,3.635 0.615,0.198 10 false N118*A
*A for RHD *B for LHD
*1 No. 4 CAN Junction Connector - -
*a Rear view of wire harness connector
(to No. 4 CAN Junction Connector)
- -


Wiring Color
Code Color (CANH Side) Color (CANL Side) Connect to

*: w/ Tire Pressure Warning System (Tire Inflation Pressure Display Function)

N118 SB W Central gateway ECU (network gateway ECU)
N119 GR W Brake actuator assembly (skid control ECU)
N120 R W Airbag sensor assembly
N121 P W Steering sensor
N123 G W Power steering ECU assembly
N177 B W Tire pressure warning ECU and receiver*


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N123-1 (CANH) - N123-2 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher



c.

Reconnect the N123 No. 4 CAN junction connector.


Result:
Proceed to
OK
NG



OK

88.CHECK FOR SHORT IN CAN BUS WIRES (NO. 4 CAN JUNCTION CONNECTOR - STEERING SENSOR)

NG

91.CHECK FOR SHORT IN CAN BUS WIRES (POWER STEERING ECU ASSEMBLY - NO. 4 CAN JUNCTION CONNECTOR)
88.CHECK FOR SHORT IN CAN BUS WIRES (NO. 4 CAN JUNCTION CONNECTOR - STEERING SENSOR)
a.

Disconnect the N121 No. 4 CAN junction connector.

HINT:
·

Before disconnecting the connectors, make a note of where it is connected.

·

Reconnect the connector to its original position.



C414817C01
5.25,2.833 5.604,2.573 5.604,2.573 5.771,2.573 true 5.26,2.99 5.594,3.219 5.594,3.219 5.76,3.219 true 5.833,2.521 6.448,2.719 0.615,0.198 10 false CANH 5.833,3.167 6.448,3.365 0.615,0.198 10 false CANL 2.063,2.406 2.677,2.604 0.615,0.198 10 false N121*B 2.063,2.146 2.677,2.344 0.615,0.198 10 false N120*B 4.229,2.198 4.844,2.396 0.615,0.198 10 false *a 0.146,0.083 0.76,0.281 0.615,0.198 10 false *1 2.063,2.677 2.677,2.875 0.615,0.198 10 false N177*B 2.073,2.917 2.688,3.115 0.615,0.198 10 false N120*A 2.063,1.896 2.677,2.094 0.615,0.198 10 false N119*B 2.063,1.635 2.677,1.833 0.615,0.198 10 false N118*B 2.604,2.677 3.219,2.875 0.615,0.198 10 false N121*A 2.604,2.146 3.219,2.344 0.615,0.198 10 false N177*A 2.604,2.406 3.219,2.604 0.615,0.198 10 false N123*A 2.073,3.188 2.688,3.385 0.615,0.198 10 false N119*A 2.073,3.438 2.688,3.635 0.615,0.198 10 false N118*A
*A for RHD *B for LHD
*1 No. 4 CAN Junction Connector - -
*a Rear view of wire harness connector
(to No. 4 CAN Junction Connector)
- -


Wiring Color
Code Color (CANH Side) Color (CANL Side) Connect to

*1: w/ Variable Flow Control Solenoid Valve

*2: w/ Tire Pressure Warning System (Tire Inflation Pressure Display Function)

N118 SB W Central gateway ECU (network gateway ECU)
N119 GR W Brake actuator assembly (skid control ECU)
N120 R W Airbag sensor assembly
N121 P W Steering sensor
N123 G W Power steering ECU assembly*1
N177 B W Tire pressure warning ECU and receiver*2


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N121-1 (CANH) - N121-2 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher



c.

Reconnect the N121 No. 4 CAN junction connector.


Result:
Proceed to
OK
NG



OK

89.CHECK VEHICLE TYPE

NG

92.CHECK FOR SHORT IN CAN BUS WIRES (STEERING SENSOR - NO. 4 CAN JUNCTION CONNECTOR)
89.CHECK VEHICLE TYPE
a.

Check for vehicle type.


Result:
Result Proceed to
w/o Tire Pressure Warning System (Tire Inflation Pressure Display Function) A
w/ Tire Pressure Warning System (Tire Inflation Pressure Display Function) B



A

REPLACE NO. 4 CAN JUNCTION CONNECTOR

B

93.CHECK FOR SHORT IN CAN BUS WIRES (NO. 4 CAN JUNCTION CONNECTOR - TIRE PRESSURE WARNING ECU AND RECEIVER)
90.CHECK FOR SHORT IN CAN BUS WIRES (BRAKE ACTUATOR ASSEMBLY [SKID CONTROL ECU] - NO. 4 CAN JUNCTION CONNECTOR)
a.
C414214C04
1.5,0.24 1.948,0.521 0.448,0.281 0.646,0.969 0.813,0.969 0.813,0.969 0.813,1.469 true 1.24,2.479 1.031,2.479 1.031,2.479 0.875,1.823 true 1.604,0.313 2.063,0.51 0.458,0.198 10 false A28 0.094,0.115 0.552,0.313 0.458,0.198 10 false *a 0.24,0.906 0.698,1.104 0.458,0.198 10 false CANH 1.313,2.406 1.771,2.604 0.458,0.198 10 false CANL
*a Front view of wire harness connector
(to Brake Actuator Assembly [Skid Control ECU])


Disconnect the A28 brake actuator assembly (skid control ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A28-26 (CANH) - A28-14 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



c.

Reconnect the A28 brake actuator assembly (skid control ECU) connector.


Result:
Proceed to
OK
NG



OK

REPLACE BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU)

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (BRAKE ACTUATOR ASSEMBLY [SKID CONTROL ECU] - NO. 4 CAN JUNCTION CONNECTOR)

91.CHECK FOR SHORT IN CAN BUS WIRES (POWER STEERING ECU ASSEMBLY - NO. 4 CAN JUNCTION CONNECTOR)
a.
C414354C01
1.49,0.219 1.948,0.469 0.458,0.25 0.792,1.677 0.938,1.677 0.938,1.677 1.125,1.302 true 1.594,1.688 1.438,1.688 1.438,1.688 1.292,1.292 true 1.594,0.26 2.052,0.458 0.458,0.198 10 false N36 0.167,0.115 0.625,0.313 0.458,0.198 10 false *a 0.365,1.604 0.979,1.802 0.615,0.198 10 false CANH 1.625,1.604 2.24,1.802 0.615,0.198 10 false CANL
*a Front view of wire harness connector
(to Power Steering ECU Assembly)


Disconnect the N36 power steering ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N36-1 (CANH) - N36-2 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



c.

Reconnect the N36 power steering ECU assembly connector.


Result:
Proceed to
OK
NG



OK

REPLACE POWER STEERING ECU ASSEMBLY

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (POWER STEERING ECU ASSEMBLY - NO. 4 CAN JUNCTION CONNECTOR)

92.CHECK FOR SHORT IN CAN BUS WIRES (STEERING SENSOR - NO. 4 CAN JUNCTION CONNECTOR)
a.
C369124C70
0.552,1.615 1.073,1.865 0.521,0.25 1,0.75 1.25,0.75 1.25,0.75 1.667,1.75 true 1.083,2.667 1.333,2.667 1.333,2.667 1.667,2 true 0.146,0.156 0.458,0.354 0.313,0.198 10 false *a 0.719,1.667 1.146,1.875 0.427,0.208 10 false N3 0.604,0.688 1.063,0.885 0.458,0.198 10 false CANH 0.708,2.594 1.167,2.792 0.458,0.198 10 false CANL
*a Front view of wire harness connector
(to Steering Sensor)


Disconnect the N3 steering sensor connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N3-3 (CANH) - N3-8 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



c.

Reconnect the N3 steering sensor connector.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (STEERING SENSOR - NO. 4 CAN JUNCTION CONNECTOR)

93.CHECK FOR SHORT IN CAN BUS WIRES (NO. 4 CAN JUNCTION CONNECTOR - TIRE PRESSURE WARNING ECU AND RECEIVER)
a.

Disconnect the N177 No. 4 CAN junction connector.

HINT:
·

Before disconnecting the connectors, make a note of where it is connected.

·

Reconnect the connector to its original position.



C414817C01
5.25,2.833 5.604,2.573 5.604,2.573 5.771,2.573 true 5.26,2.99 5.594,3.219 5.594,3.219 5.76,3.219 true 5.833,2.521 6.448,2.719 0.615,0.198 10 false CANH 5.833,3.167 6.448,3.365 0.615,0.198 10 false CANL 2.063,2.406 2.677,2.604 0.615,0.198 10 false N121*B 2.063,2.146 2.677,2.344 0.615,0.198 10 false N120*B 4.229,2.198 4.844,2.396 0.615,0.198 10 false *a 0.146,0.083 0.76,0.281 0.615,0.198 10 false *1 2.063,2.677 2.677,2.875 0.615,0.198 10 false N177*B 2.073,2.917 2.688,3.115 0.615,0.198 10 false N120*A 2.063,1.896 2.677,2.094 0.615,0.198 10 false N119*B 2.063,1.635 2.677,1.833 0.615,0.198 10 false N118*B 2.604,2.677 3.219,2.875 0.615,0.198 10 false N121*A 2.604,2.146 3.219,2.344 0.615,0.198 10 false N177*A 2.604,2.406 3.219,2.604 0.615,0.198 10 false N123*A 2.073,3.188 2.688,3.385 0.615,0.198 10 false N119*A 2.073,3.438 2.688,3.635 0.615,0.198 10 false N118*A
*A for RHD *B for LHD
*1 No. 4 CAN Junction Connector - -
*a Rear view of wire harness connector
(to No. 4 CAN Junction Connector)
- -


Wiring Color
Code Color (CANH Side) Color (CANL Side) Connect to

*: w/ Variable Flow Control Solenoid Valve

N118 SB W Central gateway ECU (network gateway ECU)
N119 GR W Brake actuator assembly (skid control ECU)
N120 R W Airbag sensor assembly
N121 P W Steering sensor
N123 G W Power steering ECU assembly*
N177 B W Tire pressure warning ECU and receiver


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N177-1 (CANH) - N177-2 (CANL) Cable disconnected from negative (-) battery terminal 200 Ω or higher



c.

Reconnect the N177 No. 4 CAN junction connector.


Result:
Proceed to
OK
NG



OK

REPLACE NO. 4 CAN JUNCTION CONNECTOR

NG

94.CHECK FOR SHORT IN CAN BUS WIRES (TIRE PRESSURE WARNING ECU AND RECEIVER - NO. 4 CAN JUNCTION CONNECTOR)
94.CHECK FOR SHORT IN CAN BUS WIRES (TIRE PRESSURE WARNING ECU AND RECEIVER - NO. 4 CAN JUNCTION CONNECTOR)
a.
C369136C32
1.5,0.667 1.917,0.917 0.417,0.25 1.25,2.417 1.417,2.417 1.417,2.417 1.635,1.969 true 1.333,2.583 1.5,2.583 1.5,2.583 1.76,1.979 true 0.125,0.104 0.438,0.302 0.313,0.198 10 false *a 1.646,0.719 1.958,0.917 0.313,0.198 10 false Z3 0.833,2.344 1.271,2.531 0.438,0.188 10 false CANH 0.958,2.521 1.375,2.708 0.417,0.188 10 false CANL
*a Front view of wire harness connector
(to Tire Pressure Warning ECU and Receiver)


Disconnect the Z3 tire pressure warning ECU and receiver connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Z3-9 (CANH) - Z3-10 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



c.

Reconnect the Z3 tire pressure warning ECU and receiver connector.


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (TIRE PRESSURE WARNING ECU AND RECEIVER - NO. 4 CAN JUNCTION CONNECTOR)

95.CHECK FOR OPEN IN CAN BUS WIRE (CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU] - NO. 4 CAN JUNCTION CONNECTOR)
a.
C368242C46
1.417,0.24 1.958,0.458 0.542,0.219 2.24,1.135 2.365,0.573 2.365,0.573 2.125,0.573 true 2.073,1.792 2.271,1.792 2.271,1.792 2.146,1.292 true 1.573,0.281 2.031,0.479 0.458,0.198 10 false N21 1.719,0.5 2.177,0.698 0.458,0.198 10 false CA2L 1.677,1.708 2.156,1.906 0.479,0.198 10 false CA2H 0.073,0.052 0.531,0.25 0.458,0.198 10 false *a
*a Front view of wire harness connector
(to Central Gateway ECU [Network Gateway ECU])


Disconnect the N21 central gateway ECU (network gateway ECU) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N21-22 (CA2H) - N21-7 (CA2L) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



c.

Reconnect the N21 central gateway ECU (network gateway ECU) connector.


Result:
Proceed to
OK
NG



OK

REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)

NG

96.CHECK VEHICLE TYPE
96.CHECK VEHICLE TYPE
a.

Check for vehicle type.


Result:
Result Proceed to
w/ Airbag System A
w/o Airbag System B



A

97.CHECK FOR OPEN IN CAN BUS WIRE (AIRBAG SENSOR ASSEMBLY - NO. 4 CAN JUNCTION CONNECTOR)

B

98.CHECK FOR OPEN IN CAN BUS WIRE (NO. 2 CAN JUNCTION TERMINAL - NO. 4 CAN JUNCTION CONNECTOR)
97.CHECK FOR OPEN IN CAN BUS WIRE (AIRBAG SENSOR ASSEMBLY - NO. 4 CAN JUNCTION CONNECTOR)
a.
C414353C01
1.5,0.26 1.938,0.49 0.438,0.229 2.25,1.854 2.583,1.563 2.583,1.563 2.719,1.563 true 2.115,1.865 2.583,1.125 2.583,1.125 2.719,1.125 true 1.604,0.292 2.063,0.49 0.458,0.198 10 false N45 2.781,1.479 3.396,1.677 0.615,0.198 10 false CANL 2.781,1.052 3.396,1.25 0.615,0.198 10 false CANH 0.094,0.083 0.708,0.281 0.615,0.198 10 false *a
*a Front view of wire harness connector
(to Airbag Sensor Assembly)


Disconnect the N45 airbag sensor assembly connector.

for Type A: Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for Type A)>PRECAUTION

for Type B: Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for Type B)>PRECAUTION

for Type C: Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for Type C)>PRECAUTION


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N45-26 (CANH) - N45-27 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



c.

Reconnect the N45 airbag sensor assembly connector.


Result:
Proceed to
OK
NG



OK

NG

99.CHECK VEHICLE TYPE
98.CHECK FOR OPEN IN CAN BUS WIRE (NO. 2 CAN JUNCTION TERMINAL - NO. 4 CAN JUNCTION CONNECTOR)
a.
C369111C29
1.5,0.302 2.063,0.594 0.563,0.292 1.729,1.135 1.563,0.667 1.563,0.667 1.417,0.667 true 1.948,1.146 2.073,0.667 2.073,0.667 2.24,0.667 true 0.073,0.052 0.385,0.25 0.313,0.198 10 false *a 1.583,0.365 1.969,0.563 0.385,0.198 10 false N122 2.281,0.604 2.771,0.865 0.49,0.26 10 false CANH 0.99,0.594 1.479,0.854 0.49,0.26 10 false CANL
*a Front view of wire harness connector
(to No. 2 CAN Junction Terminal)


Disconnect the N122 No. 2 CAN junction terminal connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N122-3 (CANH) - N122-2 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



c.

Reconnect the N122 No. 2 CAN junction terminal connector.


Result:
Proceed to
OK
NG



OK

REPLACE NO. 2 CAN JUNCTION TERMINAL

NG

102.CHECK FOR OPEN IN CAN BUS WIRE (NO. 4 CAN JUNCTION CONNECTOR - NO. 2 CAN JUNCTION TERMINAL)
99.CHECK VEHICLE TYPE
a.

Check for vehicle type.


Result:
Result Proceed to
except Wagon A
for Wagon B



A

100.CHECK FOR OPEN IN CAN BUS WIRE (NO. 4 CAN JUNCTION CONNECTOR - AIRBAG SENSOR ASSEMBLY)

B

103.CHECK FOR OPEN IN CAN BUS WIRE (NO. 4 CAN JUNCTION CONNECTOR - AIRBAG SENSOR ASSEMBLY)
100.CHECK FOR OPEN IN CAN BUS WIRE (NO. 4 CAN JUNCTION CONNECTOR - AIRBAG SENSOR ASSEMBLY)
a.

Disconnect the N120 No. 4 CAN junction connector.

HINT:
·

Before disconnecting the connectors, make a note of where it is connected.

·

Reconnect the connector to its original position.



C414494C01
5.25,2.833 5.604,2.573 5.604,2.573 5.771,2.573 true 5.26,2.99 5.594,3.219 5.594,3.219 5.76,3.219 true 5.833,2.521 6.448,2.719 0.615,0.198 10 false CANH 5.833,3.167 6.448,3.365 0.615,0.198 10 false CANL 2.063,2.427 2.677,2.625 0.615,0.198 10 false N121 2.063,2.177 2.677,2.375 0.615,0.198 10 false N120 4.229,2.198 4.844,2.396 0.615,0.198 10 false *a 0.146,0.083 0.76,0.281 0.615,0.198 10 false *1 2.063,2.677 2.677,2.875 0.615,0.198 10 false N123 2.063,1.948 2.677,2.146 0.615,0.198 10 false N119 2.063,1.667 2.677,1.865 0.615,0.198 10 false N118
*1 No. 4 CAN Junction Connector - -
*a Rear view of wire harness connector
(to No. 4 CAN Junction Connector)
- -


Wiring Color
Code Color (CANH Side) Color (CANL Side) Connect to

*1: w/ VSC OFF Switch

*2: w/o VSC OFF Switch

*3: w/ Variable Flow Control Solenoid Valve

N118 SB W Central gateway ECU (network gateway ECU)
N119 GR W Brake actuator assembly (skid control ECU)
N120 R W Airbag sensor assembly
N121 P W
·

Steering sensor*1

·

Combination switch ECU sub-assembly*2


N123 G W Power steering ECU assembly*3


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N120-1 (CANH) - N120-2 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



c.

Reconnect the N120 No. 4 CAN junction connector.


Result:
Proceed to
OK
NG



OK

101.CHECK FOR OPEN IN CAN BUS WIRE (NO. 4 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU])

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 4 CAN JUNCTION CONNECTOR - AIRBAG SENSOR ASSEMBLY)

101.CHECK FOR OPEN IN CAN BUS WIRE (NO. 4 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU])
a.

Disconnect the N118 No. 4 CAN junction connector.

HINT:
·

Before disconnecting the connectors, make a note of where it is connected.

·

Reconnect the connector to its original position.



C414203C01
5.25,2.833 5.604,2.573 5.604,2.573 5.771,2.573 true 5.26,2.99 5.594,3.219 5.594,3.219 5.76,3.219 true 5.833,2.521 6.448,2.719 0.615,0.198 10 false CANH 5.833,3.167 6.448,3.365 0.615,0.198 10 false CANL 2.063,2.427 2.677,2.625 0.615,0.198 10 false N121 2.063,2.177 2.677,2.375 0.615,0.198 10 false N120 4.229,2.198 4.844,2.396 0.615,0.198 10 false *a 0.146,0.083 0.76,0.281 0.615,0.198 10 false *1 2.063,2.677 2.677,2.875 0.615,0.198 10 false N123*A 2.073,2.917 2.688,3.115 0.615,0.198 10 false N124*A 2.063,1.948 2.677,2.146 0.615,0.198 10 false N119 2.063,1.667 2.677,1.865 0.615,0.198 10 false N118 2.604,2.677 3.219,2.875 0.615,0.198 10 false N124*B
*A for RHD *B for LHD
*1 No. 4 CAN Junction Connector - -
*a Rear view of wire harness connector
(to No. 4 CAN Junction Connector)
- -


Wiring Color
Code Color (CANH Side) Color (CANL Side) Connect to

*1: w/ Airbag System

*2: w/ VSC OFF Switch

*3: w/o VSC OFF Switch

*4: w/ Variable Flow Control Solenoid Valve

*5: w/o Airbag System

N118 SB W Central gateway ECU (network gateway ECU)
N119 GR W Brake actuator assembly (skid control ECU)
N120 R W Airbag sensor assembly*1
N121 P W
·

Steering sensor*2

·

Combination switch ECU sub-assembly*3


N123 G W Power steering ECU assembly*4
N124 L W No. 2 CAN junction terminal*5


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N118-1 (CANH) - N118-2 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



c.

Reconnect the N118 No. 4 CAN junction connector.


Result:
Proceed to
OK
NG



OK

REPLACE NO. 4 CAN JUNCTION CONNECTOR

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 4 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU])

102.CHECK FOR OPEN IN CAN BUS WIRE (NO. 4 CAN JUNCTION CONNECTOR - NO. 2 CAN JUNCTION TERMINAL)
a.

Disconnect the N124 No. 4 CAN junction connector.

HINT:
·

Before disconnecting the connectors, make a note of where it is connected.

·

Reconnect the connector to its original position.



C414493C01
5.25,2.833 5.604,2.573 5.604,2.573 5.771,2.573 true 5.26,2.99 5.594,3.219 5.594,3.219 5.76,3.219 true 5.833,2.521 6.448,2.719 0.615,0.198 10 false CANH 5.833,3.167 6.448,3.365 0.615,0.198 10 false CANL 2.063,2.427 2.677,2.625 0.615,0.198 10 false N121 4.229,2.198 4.844,2.396 0.615,0.198 10 false *a 0.146,0.083 0.76,0.281 0.615,0.198 10 false *1 2.063,2.677 2.677,2.875 0.615,0.198 10 false N123*A 2.073,2.917 2.688,3.115 0.615,0.198 10 false N124*A 2.063,1.948 2.677,2.146 0.615,0.198 10 false N119 2.063,1.667 2.677,1.865 0.615,0.198 10 false N118 2.604,2.677 3.219,2.875 0.615,0.198 10 false N124*B
*A for RHD *B for LHD
*1 No. 4 CAN Junction Connector - -
*a Rear view of wire harness connector
(to No. 4 CAN Junction Connector)
- -


Wiring Color
Code Color (CANH Side) Color (CANL Side) Connect to

*1: w/ VSC OFF Switch

*2: w/o VSC OFF Switch

*3: w/ Variable Flow Control Solenoid Valve

N118 SB W Central gateway ECU (network gateway ECU)
N119 GR W Brake actuator assembly (skid control ECU)
N121 P W
·

Steering sensor*1

·

Combination switch ECU sub-assembly*2


N123 G W Power steering ECU assembly*3
N124 L W No. 2 CAN junction terminal


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N124-1 (CANH) - N124-2 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



c.

Reconnect the N124 No. 4 CAN junction connector.


Result:
Proceed to
OK
NG



OK

101.CHECK FOR OPEN IN CAN BUS WIRE (NO. 4 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU])

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 4 CAN JUNCTION CONNECTOR - NO. 2 CAN JUNCTION TERMINAL)

103.CHECK FOR OPEN IN CAN BUS WIRE (NO. 4 CAN JUNCTION CONNECTOR - AIRBAG SENSOR ASSEMBLY)
a.

Disconnect the N120 No. 4 CAN junction connector.

HINT:
·

Before disconnecting the connectors, make a note of where it is connected.

·

Reconnect the connector to its original position.



C414817C01
5.25,2.833 5.604,2.573 5.604,2.573 5.771,2.573 true 5.26,2.99 5.594,3.219 5.594,3.219 5.76,3.219 true 5.833,2.521 6.448,2.719 0.615,0.198 10 false CANH 5.833,3.167 6.448,3.365 0.615,0.198 10 false CANL 2.063,2.406 2.677,2.604 0.615,0.198 10 false N121*B 2.063,2.146 2.677,2.344 0.615,0.198 10 false N120*B 4.229,2.198 4.844,2.396 0.615,0.198 10 false *a 0.146,0.083 0.76,0.281 0.615,0.198 10 false *1 2.063,2.677 2.677,2.875 0.615,0.198 10 false N177*B 2.073,2.917 2.688,3.115 0.615,0.198 10 false N120*A 2.063,1.896 2.677,2.094 0.615,0.198 10 false N119*B 2.063,1.635 2.677,1.833 0.615,0.198 10 false N118*B 2.604,2.677 3.219,2.875 0.615,0.198 10 false N121*A 2.604,2.146 3.219,2.344 0.615,0.198 10 false N177*A 2.604,2.406 3.219,2.604 0.615,0.198 10 false N123*A 2.073,3.188 2.688,3.385 0.615,0.198 10 false N119*A 2.073,3.438 2.688,3.635 0.615,0.198 10 false N118*A
*A for RHD *B for LHD
*1 No. 4 CAN Junction Connector - -
*a Rear view of wire harness connector
(to No. 4 CAN Junction Connector)
- -


Wiring Color
Code Color (CANH Side) Color (CANL Side) Connect to

*1: w/ Variable Flow Control Solenoid Valve

*2: w/ Tire Pressure Warning System (Tire Inflation Pressure Display Function)

N118 SB W Central gateway ECU (network gateway ECU)
N119 GR W Brake actuator assembly (skid control ECU)
N120 R W Airbag sensor assembly
N121 P W Steering sensor
N123 G W Power steering ECU assembly*1
N177 B W Tire pressure warning ECU and receiver*2


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N120-1 (CANH) - N120-2 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



c.

Reconnect the N120 No. 4 CAN junction connector.


Result:
Proceed to
OK
NG



OK

104.CHECK FOR OPEN IN CAN BUS WIRE (NO. 4 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU])

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 4 CAN JUNCTION CONNECTOR - AIRBAG SENSOR ASSEMBLY)

104.CHECK FOR OPEN IN CAN BUS WIRE (NO. 4 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU])
a.

Disconnect the N118 No. 4 CAN junction connector.

HINT:
·

Before disconnecting the connectors, make a note of where it is connected.

·

Reconnect the connector to its original position.



C414817C01
5.25,2.833 5.604,2.573 5.604,2.573 5.771,2.573 true 5.26,2.99 5.594,3.219 5.594,3.219 5.76,3.219 true 5.833,2.521 6.448,2.719 0.615,0.198 10 false CANH 5.833,3.167 6.448,3.365 0.615,0.198 10 false CANL 2.063,2.406 2.677,2.604 0.615,0.198 10 false N121*B 2.063,2.146 2.677,2.344 0.615,0.198 10 false N120*B 4.229,2.198 4.844,2.396 0.615,0.198 10 false *a 0.146,0.083 0.76,0.281 0.615,0.198 10 false *1 2.063,2.677 2.677,2.875 0.615,0.198 10 false N177*B 2.073,2.917 2.688,3.115 0.615,0.198 10 false N120*A 2.063,1.896 2.677,2.094 0.615,0.198 10 false N119*B 2.063,1.635 2.677,1.833 0.615,0.198 10 false N118*B 2.604,2.677 3.219,2.875 0.615,0.198 10 false N121*A 2.604,2.146 3.219,2.344 0.615,0.198 10 false N177*A 2.604,2.406 3.219,2.604 0.615,0.198 10 false N123*A 2.073,3.188 2.688,3.385 0.615,0.198 10 false N119*A 2.073,3.438 2.688,3.635 0.615,0.198 10 false N118*A
*A for RHD *B for LHD
*1 No. 4 CAN Junction Connector - -
*a Rear view of wire harness connector
(to No. 4 CAN Junction Connector)
- -


Wiring Color
Code Color (CANH Side) Color (CANL Side) Connect to

*1: w/ Variable Flow Control Solenoid Valve

*2: w/ Tire Pressure Warning System (Tire Inflation Pressure Display Function)

N118 SB W Central gateway ECU (network gateway ECU)
N119 GR W Brake actuator assembly (skid control ECU)
N120 R W Airbag sensor assembly
N121 P W Steering sensor
N123 G W Power steering ECU assembly*1
N177 B W Tire pressure warning ECU and receiver*2


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
N118-1 (CANH) - N118-2 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



c.

Reconnect the N118 No. 4 CAN junction connector.


Result:
Proceed to
OK
NG



OK

REPLACE NO. 4 CAN JUNCTION CONNECTOR

NG

REPAIR OR REPLACE CAN BUS WIRE OR CONNECTOR (NO. 4 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU [NETWORK GATEWAY ECU])