These DTCs are stored when a malfunction occurs in the navigation antenna assembly circuit.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B15C111 | GNSS Antenna Circuit Short to Ground | Current to the navigation antenna assembly is higher than the malfunction threshold for 10 seconds or more when the ignition switch is ON
(Short circuit) |
·
Telematics transceiver ·
Navigation antenna assembly ·
Antenna cord sub-assembly ·
Antenna divider |
| B15C113 | GNSS Antenna Circuit Open | Current to the navigation antenna assembly is lower than the malfunction threshold for 10 seconds or more when the ignition switch is ON
(Open circuit) |
·
Telematics transceiver ·
Navigation antenna assembly ·
Antenna cord sub-assembly ·
Antenna divider |
Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Telematics System.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for Toyota Connected Services)>PRECAUTION
When replacing the telematics transceiver, make sure to replace it with a new one.
Turn the ignition switch to ON and wait for 10 seconds or more.
Clear the DTCs.
Check for DTCs and check that no DTCs are output.
No DTCs are output.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG
Remove the navigation antenna assembly.
Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION ANTENNA>REMOVAL
Inspect the navigation antenna assembly.
Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION ANTENNA>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Navigation Antenna Assembly) |
| *b | Front view of wire harness connector
(to Antenna Divider) |
| *c | Front view of wire harness connector
(to Telematics Transceiver) |
Disconnect the antenna cord sub-assembly from the navigation antenna assembly connector.
Disconnect the antenna cord sub-assembly from the antenna divider connector.
Disconnect the antenna cord sub-assembly from the telematics transceiver connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A-3 - B-6 | Always | Below 1 Ω |
| A-3a - B-6a | Always | Below 1 Ω |
| A-3 or B-6 - Body ground | Always | 10 kΩ or higher |
| B-5 - GPS-1 (ANT2) | Always | Below 1 Ω |
| B-5a - GPS-1a | Always | Below 1 Ω |
| B-5 or GPS-1 (ANT2) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO ANTENNA CORD (for Instrument Panel Side)>REMOVAL
| *a | Component without harness connected
(Antenna Divider) |
Remove the antenna divider.
Click hereAudio / Visual / Telematics>TELEMATICS>ANTENNA DIVIDER>REMOVAL
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 5 - 6 | Always | Below 1 Ω |
| 5a - 6a | Always | Below 1 Ω |
| 5 - 5a | Always | 10 kΩ or higher |
| 6 - 6a | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the telematics transceiver with a new one.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER (for RHD)>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT