These DTCs are stored when a malfunction occurs in the navigation antenna assembly circuit.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B15C111 | GNSS Antenna Circuit Short to Ground | Current to the navigation antenna assembly is higher than the malfunction threshold for 10 seconds or more when the ignition switch is ON
(Short circuit) |
·
Telematics transceiver ·
Navigation antenna assembly ·
Antenna cord sub-assembly ·
Antenna divider* ·
Harness or connector |
| B15C113 | GNSS Antenna Circuit Open | Current to the navigation antenna assembly is lower than the malfunction threshold for 10 seconds or more when the ignition switch is ON
(Open circuit) |
·
Telematics transceiver ·
Navigation antenna assembly ·
Antenna cord sub-assembly ·
Antenna divider* ·
Harness or connector |
*: Standard Roof
Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Telematics System.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for ERA-GLONASS)>PRECAUTION
When replacing the telematics transceiver, make sure to replace it with a new one.
Turn the ignition switch to ON and wait for 20 seconds or more.
Clear the DTCs.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for ERA-GLONASS)>DTC CHECK / CLEAR
Check for DTCs and check that no DTCs are output.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for ERA-GLONASS)>DTC CHECK / CLEAR
No DTCs are output.
| Result | Proceed to |
|---|---|
| OK | A |
| NG (for High roof) | B |
| NG (for Standard roof) | C |
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
C
Remove the navigation antenna assembly.
Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION ANTENNA>REMOVAL
Inspect the navigation antenna assembly.
Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION ANTENNA>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Navigation Antenna Assembly) |
| *b | Front view of wire harness connector
(to Wire Harness) |
Disconnect the antenna cord sub-assembly from the navigation antenna assembly connector.
Disconnect the antenna cord sub-assembly from the wire harness connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B-3 - N216-4 (GNSS) | Always | Below 1 Ω |
| B-3a - N216-4a | Always | Below 1 Ω |
| B-3 or N216-4 (GNSS) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO ANTENNA CORD (for Instrument Panel Side)>REMOVAL
Disconnect the N216 antenna cord sub-assembly connector.
Disconnect the N214 telematics transceiver connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N216-4 (GNSS) - N214-1 (ANT2) | Always | Below 1 Ω |
| N216-4a - N214-1a | Always | Below 1 Ω |
| N216-4 (GNSS) or N214-1 (ANT2) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the telematics transceiver with a new one.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER (for LHD)>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Remove the navigation antenna assembly.
Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION ANTENNA>REMOVAL
Inspect the navigation antenna assembly.
Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION ANTENNA>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Navigation Antenna Assembly) |
| *b | Front view of wire harness connector
(to Antenna Divider) |
| *c | Front view of wire harness connector
(to Wire Harness) |
Disconnect the antenna cord sub-assembly from the navigation antenna assembly connector.
Disconnect the antenna cord sub-assembly from the antenna divider connector.
Disconnect the antenna cord sub-assembly from the wire harness connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| B-3 - C-6 | Always | Below 1 Ω |
| C-5 - N216-4 (GNSS) | Always | Below 1 Ω |
| B-3a - C-6a | Always | Below 1 Ω |
| C-5a - N216-4a | Always | Below 1 Ω |
| B-3 or C-6 - Body ground | Always | 10 kΩ or higher |
| C-5 or N216-4 (GNSS) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO ANTENNA CORD (for Instrument Panel Side)>REMOVAL
Disconnect the N216 antenna cord sub-assembly connector.
Disconnect the N214 telematics transceiver connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N216-4 (GNSS) - N214-1 (ANT2) | Always | Below 1 Ω |
| N216-4a - N214-1a | Always | Below 1 Ω |
| N216-4 (GNSS) or N214-1 (ANT2) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component without harness connected
(Antenna Divider) |
Remove the antenna divider.
Click hereAudio / Visual / Telematics>TELEMATICS>ANTENNA DIVIDER>REMOVAL
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 5 - 6 | Always | Below 1 Ω |
| 5a - 6a | Always | Below 1 Ω |
| 5 - 5a | Always | 10 kΩ or higher |
| 6 - 6a | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the telematics transceiver with a new one.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER (for LHD)>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT