If the telematics transceiver detects an error in communication between the telematics transceiver and the airbag sensor assembly as a result of the telematics transceiver self check, this DTC will be stored.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B15C464 | Airbag Signal Signal Plausibility Failure | Telematics transceiver detects an error in signals from airbag sensor assembly when ignition switch is ON | ·
Airbag system ·
Harness or connector ·
Airbag sensor assembly ·
Telematics transceiver |
Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Telematics System.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for ERA-GLONASS)>PRECAUTION
The vehicle is equipped with an SRS (Supplemental Restraint System) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the Precaution in the SRS.
for Type A: Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for Type A)>PRECAUTION
for Type C: Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for Type C)>PRECAUTION
When replacing the telematics transceiver, make sure to replace it with a new one.
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY
When disconnecting and reconnecting the battery.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE
When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART
Turn the ignition switch to ON.
Connect the GTS to the DLC3.
Turn the ignition switch to ON and wait for 10 seconds.
Turn the GTS on.
Check the DTC of "AIRBAG SYSTEM".
for Type A: Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for Type A)>DTC CHECK / CLEAR
for Type C: Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for Type C)>DTC CHECK / CLEAR
No DTCs are output.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for Type A: Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for Type A)>DIAGNOSTIC TROUBLE CODE CHART
for Type C: Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM (for Type C)>DIAGNOSTIC TROUBLE CODE CHART
Turn the ignition switch to ON.
Connect the GTS to the DLC3.
Turn the ignition switch to ON and wait for 10 seconds or more.
Turn the GTS on.
Check for DTCs and check that no DTCs are output.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for ERA-GLONASS)>DTC CHECK / CLEAR
No DTCs are output.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG
| *a | Component with harness connected
(Telematics Transceiver) |
Remove the telematics transceiver but do not disconnect the connectors.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER (for LHD)>REMOVAL
Check the input waveform.
Check the signal waveform according to the condition(s) in the table below. (Check the waveform from the back of the wire harness connector of the telematics transceiver while the airbag sensor assembly connectors are connected.)
| Item | Condition |
|---|---|
| Tester connection | N209-13 (GSW) - Body ground |
| Tool setting | 5.0 V/DIV., 20 ms./DIV. |
| Vehicle condition | Ignition switch ON |
The waveform is similar to that shown in the illustration.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the telematics transceiver with a new one.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER (for LHD)>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Disconnect the N209 telematics transceiver connector.
Disconnect the N45 airbag sensor assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N209-13 (GSW) - N45-23 (GSW3) | Always | Below 1 Ω |
| N209-13 (GSW) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG