Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Registration for Telematics System.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS SYSTEM (for ERA-GLONASS)>REGISTRATION
When replacing the telematics transceiver, make sure to replace it with a new one.
Inspect the fuse for circuits related to this system before performing the following procedure.
Check vehicle type.
| Result | Proceed to |
|---|---|
| for High roof | A |
| for Standard roof | B |
A
B
Disconnect the N209 telematics transceiver connector.
Disconnect the a19 map light assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| a19-21 (GND3) - N209-3 (SIG-) | Always | Below 1 Ω |
| a19-21 (GND3) or N209-3 (SIG-) - Body ground | Always | 10 kΩ or higher |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| a19-19 (RRID) - Body ground | Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component without harness connected
(Map Light Assembly) |
Remove the map light assembly.
Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL
Apply battery voltage to the connector.
| Measurement Condition | Condition | Specified Condition |
|---|---|---|
| Battery positive (+) → 19 (RRID)
Battery negative (-) → 21 (GND3) |
Always | Manual (SOS) switch illumination comes on |
Check if the manual (SOS) switch illuminates.
Manual (SOS) switch illuminates.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the telematics transceiver with a new one.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER (for LHD)>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Disconnect the N209 telematics transceiver connector.
Disconnect the a22 map light assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| a22-12 (GND3) - N209-3 (SIG-) | Always | Below 1 Ω |
| a22-12 (GND3) or N209-3 (SIG-) - Body ground | Always | 10 kΩ or higher |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| a22-9 (RRID) - Body ground | Ignition switch ON | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component without harness connected
(Map Light Assembly) |
Remove the map light assembly.
Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT (for Wagon)>REMOVAL
Apply battery voltage to the connector.
| Measurement Condition | Condition | Specified Condition |
|---|---|---|
| Battery positive (+) → 9 (RRID)
Battery negative (-) → 12 (GND3) |
Always | Manual (SOS) switch illumination comes on |
Check if the manual (SOS) switch illuminates.
Manual (SOS) switch illuminates.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the telematics transceiver with a new one.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER (for LHD)>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT