The radio and display receiver assembly, map light assembly and telephone microphone assembly are connected to each other using the microphone connection detection signal lines.
This DTC is stored when a microphone connection detection signal line is disconnected.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B1579 | Voice Recognition Microphone Disconnected | Microphone signal is lost | ·
Map light assembly ·
Telephone microphone assembly ·
Radio and display receiver assembly ·
Harness or connector |
Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Navigation System.
Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>PRECAUTION
Choose the model to be inspected.
| Result | Proceed to |
|---|---|
| except Wagon | A |
| for Wagon and w/ Telematics Transceiver (for Toyota Connected Services) | B |
| for Wagon and w/o Telematics Transceiver | C |
A
B
C
Disconnect the O7 radio and display receiver assembly connector.
Disconnect the a19 map light assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| O7-25 (SNS2) - a19-11 (SNS2) | Always | Below 1 Ω |
| O7-22 (MIN-) - a19-10 (MCO-) | Always | Below 1 Ω |
| O7-25 (SNS2) - Body ground | Always | 10 kΩ or higher |
| O7-22 (MIN-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component without harness connected
(Map Light Assembly) |
Remove the map light assembly.
Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| a19-11 (SNS2) - a19-10 (MCO-) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component without harness connected
(Map Light Assembly) |
Remove the map light assembly.
Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL
Disconnect the telephone microphone assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| a19-11 (SNS2) - A-1 (SNS2) | Always | Below 1 Ω |
| a19-10 (MCO-) - A-2 (MIC-) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the O7 radio and display receiver assembly connector.
Disconnect the a22 map light assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| O7-25 (SNS2) - a22-3 (SNS2) | Always | Below 1 Ω |
| O7-22 (MIN-) - a22-4 (MCO-) | Always | Below 1 Ω |
| O7-25 (SNS2) - Body ground | Always | 10 kΩ or higher |
| O7-22 (MIN-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the map light assembly.
Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT (for Wagon)>REMOVAL
| *a | Component without harness connected
(Map Light Assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| a22-3 (SNS2) - a22-4 (MCO-) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component without harness connected
(Map Light Assembly [Wire Harness Side]) |
| *b | Component without harness connected
(Map Light Assembly [Telephone Microphone Assembly Side]) |
Remove the map light assembly.
Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT (for Wagon)>REMOVAL
Disconnect the telephone microphone assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| a22-3 (SNS2) - B-1 (SNS2) | Always | Below 1 Ω |
| a22-4 (MCO-) - B-2 (MIC-) | Always | Below 1 Ω |
| a22-3 (SNS2) - Body ground | Always | 10 kΩ or higher |
| a22-4 (MCO-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the O7 radio and display receiver assembly connector.
Disconnect the a23 map light assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| O7-25 (SNS2) - a23-12 (SNS2) | Always | Below 1 Ω |
| O7-22 (MIN-) - a23-11 (MCO-) | Always | Below 1 Ω |
| O7-25 (SNS2) - Body ground | Always | 10 kΩ or higher |
| O7-22 (MIN-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the map light assembly.
Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT (for Wagon)>REMOVAL
| *a | Component without harness connected
(Map Light Assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| a23-12 (SNS2) - a23-11 (MCO-) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component without harness connected
(Map Light Assembly [Wire Harness Side]) |
| *b | Component without harness connected
(Map Light Assembly [Telephone Microphone Assembly Side]) |
Remove the map light assembly.
Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT (for Wagon)>REMOVAL
Disconnect the telephone microphone assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| a23-12 (SNS2) - B-1 (SNS2) | Always | Below 1 Ω |
| a23-11 (MCO-) - B-2 (MIC-) | Always | Below 1 Ω |
| a23-12 (SNS2) - Body ground | Always | 10 kΩ or higher |
| a23-11 (MCO-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG