Home › Engine / Hybrid System › 1GD-FTV (EMISSION CONTROL) › EGR VALVE (w/o EGR Cooler) › from 2021.07
RM35X0E _51 Engine / Hybrid System _079220 1GD-FTV EMISSION CONTROL _0389335 EGR VALVE(w/o EGR Cooler) A

1GD-FTV EMISSION CONTROL  EGR VALVE(w/o EGR Cooler)  INSTALLATION  


PROCEDURE

Hide 25800 1.INSTALL ELECTRIC EGR CONTROL VALVE ASSEMBLY

a.

Install a new gasket and the electric EGR control valve assembly to the EGR valve adapter sub-assembly with the 2 bolts.

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)


b.

Connect the No. 9 water by-pass hose to the electric EGR control valve assembly, and slide the clamp to secure the hose.


c.

Attach the clamp and connect the connector to the common rail assembly.


Hide 25612 2.INSTALL NO. 2 EGR PIPE

a.

Install 2 new gaskets and the No. 2 EGR pipe to the electric EGR control valve assembly and intake manifold with the 4 nuts.

Torque:
29 N*m (296 kgf*cm, 21 ft.*lbf)


Hide 25625 3.INSTALL EGR VALVE BRACKET

a.

Install the EGR valve bracket to the electric EGR control valve assembly and intake manifold with the bolt and nut.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 82121 4.CONNECT ENGINE WIRE

a.

Attach the clamp and connect the engine wire to the No. 4 water by-pass pipe sub-assembly with the bolt.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)


b.

Attach the 2 clamps and connect the engine wire to the No. 3 water by-pass pipe sub-assembly and wire harness clamp bracket.


c.

Connect the connector to the vane pump assembly.


d.

Connect the connector to the sensor wire of the common rail assembly with the bolt.

Torque:
13 N*m (133 kgf*cm, 10 ft.*lbf)


e.

Connect the connector to the glow plug connector.


f.

Connect the connector to the electric EGR control valve assembly.


g.

Connect the 4 connectors to the 4 injector assemblies.


h.

Attach the 3 clamps and connect the engine wire to the 2 wire harness clamp brackets.


i.

Connect the connector to the camshaft position sensor.


j.

Attach the clamp and connect the connector to the intake mass air flow meter assembly.


k.

Connect the 2 connectors to the turbocharger sub-assembly.


Hide 23941 5.CONNECT NO. 1 FUEL FILTER PROTECTOR

a.

Connect the No. 1 fuel filter protector to the body.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)


b.

Attach the clamp and connect the wire harness to the No. 1 fuel filter protector.


c.

Connect the connector to the fuel filter assembly.


Hide 12632 6.INSTALL NO. 2 ENGINE COVER BRACKET

a.

Install the No. 2 engine cover bracket to the No. 3 water by-pass pipe sub-assembly and EGR valve adapter sub-assembly with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 23265C 7.INSTALL GAS FILTER

a.

Attach the clamp and install the gas filter to the gas filter bracket.


b.

Connect the vacuum hose to the intake manifold.


Hide 89421C 8.INSTALL DIESEL TURBO PRESSURE SENSOR

a.
A493095C01
0.333,0.167 0.417,0.167 0.417,0.167 0.583,0.667 true 0.333,2.083 0.417,2.083 0.417,2.083 0.667,2.5 true 0.333,3 0.417,3 0.417,3 0.667,2.833 true 0.719,2.896 0.885,2.896 true 0.083,0.083 0.333,0.25 0.25,0.167 10 true *b 0.083,2 0.333,2.167 0.25,0.167 10 true *b 0.083,2.917 0.333,3.083 0.25,0.167 10 true *c 0.969,2.813 1.219,2.979 0.25,0.167 10 false *a 2.167,2.333 2.417,2.5 0.25,0.167 10 false *d 3.167,2.5 3.417,2.667 0.25,0.167 10 false *e
*a Vacuum Hose
*b Protrusion
*c Paint Mark
*d 0 to 4 mm (0 to 0.157 in.)
*e 120°


Connect the vacuum hose to the diesel turbo pressure sensor, and slide the clip to secure the vacuum hose.


b.

Install the diesel turbo pressure sensor to the No. 3 water by-pass pipe sub-assembly with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


c.

Connect the diesel turbo pressure sensor connector.


Hide 16278 9.INSTALL NO. 2 WATER BY-PASS PIPE

a.

Install the No. 2 water by-pass pipe to the cylinder head cover sub-assembly and No. 3 water by-pass pipe sub-assembly with the 3 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


b.

Connect the No. 16 water by-pass hose to the EGR pipe stay, and slide the clamp to secure the hose.


c.

Connect the No. 15 water by-pass hose to the water by-pass pipe, and slide the clamp to secure the hose.


d.

w/ Heater:

Connect the No. 13 water by-pass hose to the No. 2 water by-pass pipe, and slide the clamp to secure the hose.


e.

w/ Viscous Heater:

Connect the water by-pass hose sub-assembly to the No. 2 water by-pass pipe, and slide the clamp to secure the hose.


f.

for Laminated EGR Pre-cooler:

Attach the clamp, connect the No. 18 water by-pass hose to the EGR pipe with cooler sub-assembly, and slide the clamp to secure the hose.


Hide 87209 10.INSTALL WATER HOSE SUB-ASSEMBLY (w/ Heater)

a.

w/o Rear Heater:

Install the 2 water hose sub-assemblies to the air conditioning unit assembly and No. 2 water by-pass pipe, and slide the 4 clamps to secure the hoses.


b.

w/ Rear Heater:

i.

Install the 2 water hose sub-assemblies to the air conditioning unit assembly and No. 2 water by-pass pipe, and slide the 4 clamps to secure the hoses.


ii.

Connect the 2 water hose sub-assemblies to the water pipe, and slide the 2 clamps to secure the hoses.



Hide 26100G 11.INSTALL DIESEL THROTTLE BODY ASSEMBLY

Hide 55701J 12.INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY

Hide 85110 13.INSTALL WINDSHIELD WIPER MOTOR ASSEMBLY

Hide 14.ADD ENGINE COOLANT