2007-2013 Highlander Kluger · Service Manual BRAKE

REASSEMBLY

Removal / installation · Vehicles built from May 2007


1. INSTALL REAR DISC

  1. C166438E01
    Align matchmarks and install the rear disc.

    NOTICE:
    When replacing the rear disc with a new one, select the installation position where the rear disc has minimal runout.


2. INSTALL PARKING BRAKE SHOE ADJUSTING HOLE PLUG
  1. Install the parking brake shoe adjusting hole plug.


3. INSTALL REAR DISC BRAKE BLEEDER PLUG
  1. Temporarily tighten the rear disc brake bleeder plug to the rear disc brake cylinder assembly.

    HINT:
    The bleeder plug will be tightened to a torque specification in the "BLEED BRAKE LINE".


4. INSTALL REAR DISC BRAKE BLEEDER PLUG CAP
  1. Install the rear disc brake bleeder plug cap to the rear disc brake bleeder plug.


5. INSTALL PISTON SEAL
  1. Apply lithium soap base glycol grease to a new piston seal.

  1. Install the piston seal to the rear disc brake cylinder assembly.

    NOTICE:
    Securely install the piston seal into the groove of the disc brake cylinder.


6. INSTALL REAR DISC BRAKE PISTON

  1. C192811E01
    Apply a light layer of lithium soap base glycol grease to the entire circumference of a new cylinder boot.

  1. Install the cylinder boot to the rear disc brake piston.

  1. Apply a light layer of lithium soap base glycol grease to the contact surface of the rear disc brake piston, and install it to the rear disc brake cylinder assembly.

    NOTICE:
    Do not install the rear disc piston forcibly in the rear disc brake cylinder assembly.


7. INSTALL CYLINDER BOOT

  1. C193906
    Install the cylinder boot to the rear disc brake cylinder assembly as shown in the illustration.

    NOTICE:
    1. Securely install the cylinder boot into the groove of the cylinder and piston.
    2. Do not damage the cylinder boot.


8. INSTALL REAR DISC BRAKE CYLINDER MOUNTING

  1. C166436
    Install the rear disc brake cylinder mounting to the rear axle with the 2 bolts.

    Torque:
    78 N*m{ 795 kgf*cm , 57 ft.*lbf }


9. INSTALL REAR DISC BRAKE BUSHING DUST BOOT
  1. Apply lithium soap base glycol grease to the seal surface of 2 new rear disc brake bushing dust boots.

  1. C166442E01
    Install the 2 rear disc brake bushing dust boots to the rear disc brake cylinder mounting.


10. INSTALL REAR DISC BRAKE CYLINDER SLIDE BUSHING
  1. Apply lithium soap base glycol grease to a new rear disc brake cylinder slide bushing.

  1. Install the rear disc brake cylinder slide bushing to the No. 2 rear disc brake cylinder slide pin.


11. INSTALL NO. 2 REAR DISC BRAKE CYLINDER SLIDE PIN
  1. Apply the lithium soap base glycol grease to the sliding part and the seal surface of the No. 2 rear disc brake cylinder slide pin.

  1. C167076E01
    Install the No. 2 rear disc brake cylinder slide pin to the rear brake cylinder mounting.


12. INSTALL NO. 1 REAR DISC BRAKE CYLINDER SLIDE PIN
  1. Apply the lithium soap base glycol grease to the sliding part and the seal surface of the No. 1 rear disc brake cylinder slide pin.

  1. C167075E01
    Install the No. 1 rear disc brake cylinder slide pin to the rear brake cylinder mounting.


13. INSTALL NO. 1 REAR DISC BRAKE PAD SUPPORT PLATE

  1. C166432E01
    Install the No. 1 rear disc brake pad support plate to the rear disc brake cylinder mounting.

    NOTICE:
    Be sure to install the No. 1 rear disc brake pad support plate to the correct position and direction.


14. INSTALL NO. 2 REAR DISC BRAKE PAD SUPPORT PLATE
  1. Install the No. 2 rear disc brake pad support plate to the rear disc brake cylinder mounting.

    NOTICE:
    Be sure to install the No. 2 rear disc brake pad support plate to the correct position and direction.


15. INSTALL REAR ANTI-SQUEAL SHIM

  1. C170588E01
    Apply disc brake grease to the inside of the 2 rear anti-squeal shims as shown in the illustration.

    NOTICE:
    1. When replacing worn pads, the rear anti-squeal shims must be replaced together with the pads.
    2. Install the shims in the correct positions and directions.
    3. Apply disc brake grease to the area that contacts the rear anti-squeal shim.
    4. Disc brake grease can come out slightly from the area where the rear anti-squeal shim is installed.
    5. Make sure that disc brake grease is not applied onto the lining surface.

  1. C170586E01
    Install the rear anti-squeal shim to each of the 2 rear brake pads.

  1. Install the pad wear indicator to the inside rear brake pad.

    NOTICE:
    Install the pad wear indicator and rear anti-squeal shims in the correct positions and directions.


16. INSTALL REAR BRAKE PAD

  1. C166431
    Install the 2 rear brake pads with rear anti-squeal shims to the rear disc brake cylinder mounting.

← INSPECTION (from Jul 2010)INSTALLATION (May 2007 – Jul 2008) →