2007-2013 Highlander Kluger · Service Manual DRIVE LINE

INSTALLATION

Removal / installation · Vehicles built from Jul 2010

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010


1. INSTALL REAR DRIVE SHAFT ASSEMBLY

  1. C166347
    Align the shaft splines and install the rear drive shaft assembly with a brass bar and hammer.

    NOTICE:
    1. Set the snap ring with the opening facing downward.
    2. Be careful not to damage the oil seal, boot, or dust cover.
    3. Install the drive shaft assembly while keeping it level.


2. INSTALL REAR AXLE CARRIER SUB-ASSEMBLY LH

  1. C166002
    Temporarily install the the rear axle carrier sub-assembly with the 2 bolts and the 2 nuts.

    NOTICE:
    1. Be careful not to damage the outboard joint boot.
    2. Be careful not to damage the speed sensor rotor.
    3. Prevent foreign matter from adhering to the speed sensor rotor.

  1. C166001
    Install the rear axle carrier sub-assembly with the 2 bolts and the 2 nuts.

    Torque:
    290 N*m{ 2956 kgf*cm , 213 ft.*lbf }

    NOTICE:
    1. Be careful not to damage the outboard joint boot.
    2. Be careful not to damage the speed sensor rotor.
    3. Prevent foreign matter from adhering to the speed sensor rotor.
    4. Do not rotate the drive shaft with the rear axle hub and bearing assembly removed.

    HINT:
    Insert the bolts from the rear side.


3. TEMPORARILY INSTALL REAR STRUT ROD ASSEMBLY

  1. C165999E01
    Check that the identification mark of the rear strut rod assembly is positioned on the inner side of the vehicle.

  1. Temporarily install the rear strut rod assembly with the 2 bolts and the 2 nuts.

    NOTICE:
    Since stopper nuts are used, temporarily tighten the bolts.


4. INSTALL REAR AXLE HUB AND BEARING ASSEMBLY LH

  1. C166348E01
    Align the matchmarks on the drive shaft and rear axle hub.

    NOTICE:
    Do not rotate the drive shaft.

  1. C165997
    Install the parking brake assembly and the rear axle hub and bearing assembly with the 4 bolts.

    Torque:
    75 N*m{ 764 kgf*cm , 55 ft.*lbf }

    NOTICE:
    Do not twist the No. 3 parking brake cable assembly when installing it.


5. INSTALL REAR DISC

  1. C166438E01
    Align matchmarks and install the rear disc.

    NOTICE:
    When replacing the rear disc with a new one, select the installation position where the rear disc has minimal runout.


6. INSTALL REAR DISC BRAKE CALIPER ASSEMBLY LH

  1. C165996
    Install the rear disc brake caliper assembly with the 2 bolts.

    Torque:
    78 N*m{ 795 kgf*cm , 57 ft.*lbf }


7. INSTALL REAR SPEED SENSOR LH

  1. C165809
    Install the rear speed sensor to the rear axle carrier sub-assembly with the bolt .

    Torque:
    8.5 N*m{ 87 kgf*cm , 75 in.*lbf }

    NOTICE:
    1. Keep the rear speed sensor tip and sensor installation hole free from foreign matter.
    2. To prevent interference with the bearing rotor, do not rotate the rear speed sensor body when inserting the rear speed sensor body or after inserting the rear speed sensor body.
    3. Do not twist the rear speed sensor wire when installing.


8. STABILIZE SUSPENSION

  1. C166003E01
    Jack up the rear axle carrier sub-assembly, placing a wooden block underneath to avoid damage. Apply load to the suspension so that the rear drive shaft assembly is positioned horizontally.

    CAUTION:
    Do not jack up the rear axle carrier sub-assembly too high as the vehicle may fall.

    NOTICE:
    Do not bend the brake dust cover.

    HINT:
    1. If the rear drive shaft assembly cannot be positioned horizontally as shown in the illustration even when the rear axle carrier sub-assembly is jacked up, apply additional load to the vehicle such as by having a person sit in the rear seat.
    2. Use the same procedure for the RH side and LH side.


9. FULLY TIGHTEN REAR NO. 2 SUSPENSION ARM ASSEMBLY LH

  1. C166008
    Fully tighten the rear No. 2 suspension arm assembly with the bolt and nut.

    Torque:
    112 N*m{ 1141 kgf*cm , 82 ft.*lbf }

    NOTICE:
    1. Since a stopper nut is used, fully tighten the bolt.
    2. The final torque must be applied under standard vehicle height conditions.


10. FULLY TIGHTEN REAR NO. 1 SUSPENSION ARM ASSEMBLY LH

  1. C166007
    Fully tighten the rear No. 1 suspension arm assembly with the bolt and nut.

    Torque:
    112 N*m{ 1141 kgf*cm , 82 ft.*lbf }

    NOTICE:
    1. Since a stopper nut is used, fully tighten the bolt.
    2. The final torque must be applied under standard vehicle height conditions.


11. FULLY TIGHTEN REAR STRUT ROD ASSEMBLY

  1. C166006
    Fully tighten the bolt.

    Torque:
    80 N*m{ 815 kgf*cm , 59 ft.*lbf }

    NOTICE:
    1. Since a stopper nut is used, fully tighten the bolt.
    2. The final torque must be applied under standard vehicle height conditions.

  1. C166005
    Fully tighten the bolt.

    Torque:
    80 N*m{ 815 kgf*cm , 59 ft.*lbf }

    NOTICE:
    1. Since a stopper nut is used, fully tighten the bolt.
    2. The final torque must be applied under standard vehicle height conditions.


12. INSTALL NO. 3 PARKING BRAKE CABLE ASSEMBLY

  1. C165998
    Install the No. 3 parking brake cable assembly with the bolt and the nut.

    Torque:
    Bolt:
    39 N*m{ 397 kgf*cm , 29 ft.*lbf }
    Nut:
    6.0 N*m{ 61 kgf*cm , 53 in.*lbf }

    NOTICE:
    Do not twist the No. 3 parking brake cable assembly when installing it.


13. INSTALL REAR AXLE SHAFT NUT LH
  1. Clean the threaded parts on the drive shaft and axle hub nut using a non-residue solvent.

    NOTICE:
    1. Be sure to perform this work for a new drive shaft.
    2. Keep the threaded parts free of oil and foreign objects.

  1. C165541
    Install a new rear axle shaft nut.

    Torque:
    294 N*m{ 2996 kgf*cm , 216 ft.*lbf }

  1. Using a chisel and hammer, stake the rear axle shaft nut.


14. INSTALL REAR DIFFERENTIAL DRAIN PLUG

  1. C166707
    Using a hexagon wrench (10 mm), install the drain plug with a new gasket.

    Torque:
    49 N*m{ 500 kgf*cm , 36 ft.*lbf }


15. ADD DIFFERENTIAL OIL
  1. Fill the rear differential carrier assembly with hypoid gear oil.


16. INSPECT DIFFERENTIAL OIL
  1. Stop the vehicle on a level place.

  1. Remove the differential filler plug and gasket.

  1. C165855E01
    Check that the oil surface is within 5 mm (0.20 in.) of the lowest position of the inner surface of the differential filler plug opening.

    NOTICE:
    1. Excessively large or small amounts of oil may cause trouble.
    2. After replacing oil, drive the vehicle and check the oil level.

    HINT:
    If necessary, fill the rear differential carrier with hypoid gear oil.

    Oil grade:
    Hypoid gear oil API GL-5
    Recommended oil viscosity:
    Above -18°C (0°F) : SAE 90
    Below -18°C (0°F) : SAE 80W or 80W-90
    Capacity:
    0.9 +/- 0.05 liters (0.95 +/- 0.05 US qts, 0.79 +/- 0.04 lmp. qts)

  1. Check for oil leakage when the oil level is low.

  1. Install the differential filler plug and a new gasket.

    Torque:
    49 N*m{ 500 kgf*cm , 36 ft.*lbf }


17. INSTALL REAR DIFFERENTIAL FILLER PLUG

  1. C166706
    Using a hexagon wrench (10 mm), install the filler plug with a new gasket.

    Torque:
    49 N*m{ 500 kgf*cm , 36 ft.*lbf }


18. INSTALL REAR WHEEL

Torque:
103 N*m{ 1050 kgf*cm , 76 ft.*lbf }


19. INSPECT AND ADJUST REAR WHEEL ALIGNMENT

HINT:
(Click here)


20. CHECK ABS SPEED SENSOR SIGNAL

HINT:
(Click here)

← INSTALLATION (Aug 2008 – Jun 2010)PRECAUTION (from May 2007) →