2007-2013 Highlander Kluger · Service Manual SUSPENSION & AXLE

INSTALLATION

Removal / installation · Vehicles built Aug 2008 – Jun 2010

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010


1. INSTALL REAR AXLE CARRIER SUB-ASSEMBLY

  1. C166002
    Temporarily install the the rear axle carrier sub-assembly with the 2 bolts and the 2 nuts.

    NOTICE:
    1. Be careful not to damage the outboard joint boot.
    2. Be careful not to damage the speed sensor rotor.
    3. Prevent foreign matter from adhering to the speed sensor rotor.

  1. C166001
    Install the rear axle carrier sub-assembly with the 2 bolts and the 2 nuts.

    Torque:
    290 N*m{ 2956 kgf*cm , 213 ft.*lbf }

    NOTICE:
    1. Be careful not to damage the outboard joint boot.
    2. Be careful not to damage the speed sensor rotor.
    3. Prevent foreign matter from adhering to the speed sensor rotor.
    4. Do not rotate the drive shaft with the rear axle hub and bearing assembly removed.

    HINT:
    Insert the bolts from the rear side.


2. TEMPORARILY INSTALL REAR STRUT ROD ASSEMBLY

  1. C165999E01
    Check that the identification mark of the rear strut rod assembly is positioned on the inner side of the vehicle.

  1. Temporarily install the rear strut rod assembly with the 2 bolts and the 2 nuts.

    NOTICE:
    Since stopper nuts are used, temporarily tighten the bolts.


3. INSTALL REAR AXLE HUB AND BEARING ASSEMBLY

  1. C166348E01
    Align the matchmarks on the drive shaft and rear axle hub.

    NOTICE:
    Do not rotate the drive shaft.

  1. C165997
    Install the parking brake assembly and the rear axle hub and bearing assembly with the 4 bolts.

    Torque:
    75 N*m{ 764 kgf*cm , 55 ft.*lbf }

    NOTICE:
    Do not twist the No. 3 parking brake cable assembly when installing it.


4. INSTALL REAR DISC

  1. C166438E01
    Align matchmarks and install the rear disc.

    NOTICE:
    When replacing the rear disc with a new one, select the installation position where the rear disc has minimal runout.


5. INSTALL REAR DISC BRAKE CALIPER ASSEMBLY

  1. C165996
    Install the rear disc brake caliper assembly with the 2 bolts.

    Torque:
    78 N*m{ 795 kgf*cm , 57 ft.*lbf }


6. TEMPORARILY INSTALL REAR AXLE SHAFT NUT

  1. C167784
    Clean the threaded parts on the rear drive shaft assembly and rear axle shaft nut using a non-residue solvent.

    NOTICE:
    1. Be sure to perform this work for a new rear drive shaft assembly.
    2. Keep the threaded parts free of oil and foreign objects.

  1. While applying the brakes, temporarily install a new rear axle shaft nut.

    Torque:
    294 N*m{ 2996 kgf*cm , 216 ft.*lbf }

    NOTICE:
    Stake the nut after inspecting for looseness and runout in the following steps.


7. INSTALL REAR SPEED SENSOR

  1. C165809
    Install the rear speed sensor to the rear axle carrier sub-assembly with the bolt .

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

    NOTICE:
    1. Keep the rear speed sensor tip and sensor installation hole free from foreign matter.
    2. To prevent interference with the bearing rotor, do not rotate the rear speed sensor body when inserting the rear speed sensor body or after inserting the rear speed sensor body.
    3. Do not twist the rear speed sensor wire when installing.


8. STABILIZE SUSPENSION

  1. C166003E01
    Jack up the rear axle carrier sub-assembly, placing a wooden block underneath to avoid damage. Apply load to the suspension so that the rear drive shaft assembly is positioned horizontally.

    CAUTION:
    Do not jack up the rear axle carrier sub-assembly too high as the vehicle may fall.

    NOTICE:
    Do not bend the brake dust cover.

    HINT:
    1. If the rear drive shaft assembly cannot be positioned horizontally as shown in the illustration even when the rear axle carrier sub-assembly is jacked up, apply additional load to the vehicle such as by having a person sit in the rear seat.
    2. Use the same procedure for the RH side and LH side.


9. FULLY TIGHTEN REAR NO. 2 SUSPENSION ARM ASSEMBLY

  1. C166008
    Fully tighten the rear No. 2 suspension arm assembly with the bolt and nut.

    Torque:
    112 N*m{ 1141 kgf*cm , 82 ft.*lbf }

    NOTICE:
    1. Since a stopper nut is used, fully tighten the bolt.
    2. The final torque must be applied under standard vehicle height conditions.


10. FULLY TIGHTEN REAR NO. 1 SUSPENSION ARM ASSEMBLY

  1. C166007
    Fully tighten the rear No. 1 suspension arm assembly with the bolt and nut.

    Torque:
    112 N*m{ 1141 kgf*cm , 82 ft.*lbf }

    NOTICE:
    1. Since a stopper nut is used, fully tighten the bolt.
    2. The final torque must be applied under standard vehicle height conditions.


11. FULLY TIGHTEN REAR STRUT ROD ASSEMBLY

  1. C166006
    Fully tighten the bolt.

    Torque:
    80 N*m{ 815 kgf*cm , 59 ft.*lbf }

    NOTICE:
    1. Since a stopper nut is used, fully tighten the bolt.
    2. The final torque must be applied under standard vehicle height conditions.

  1. C166005
    Fully tighten the bolt.

    Torque:
    80 N*m{ 815 kgf*cm , 59 ft.*lbf }

    NOTICE:
    1. Since a stopper nut is used, fully tighten the bolt.
    2. The final torque must be applied under standard vehicle height conditions.


12. INSTALL NO. 3 PARKING BRAKE CABLE ASSEMBLY

  1. C165998
    Install the No. 3 parking brake cable assembly with the bolt and the nut.

    Torque:
    Bolt:
    39 N*m{ 397 kgf*cm , 29 ft.*lbf }
    Nut:
    6.0 N*m{ 61 kgf*cm , 53 in.*lbf }

    NOTICE:
    Do not twist the No. 3 parking brake cable assembly when installing it.


13. SEPARATE REAR DISC BRAKE CALIPER ASSEMBLY

  1. C165996
    Remove the 2 bolts and separate the rear disc brake caliper assembly.

    NOTICE:
    Use wire or an equivalent tool to keep the brake caliper from hanging down by the flexible hose.


14. REMOVE REAR DISC

  1. C166438E01
    Put matchmarks on the rear disc and the axle hub.

  1. D028126
    Release the parking brake and remove the rear disc.

    HINT:
    If the disc cannot be removed easily, turn and press firmly the shoe adjuster until the wheel comes free.


15. INSPECT REAR AXLE HUB BEARING LOOSENESS

  1. C165994
    Using a dial indicator, check for looseness near the center of the rear axle hub and bearing assembly.

    Maximum looseness:
    0 mm (0 in.)

    NOTICE:
    Ensure that the dial indicator is set perpendicular to the measurement surface.

    HINT:
    If the looseness exceeds the maximum, replace the rear axle hub and bearing assembly.


16. INSPECT REAR AXLE HUB RUNOUT

  1. C165995
    Using a dial indicator, check for runout on the surface of the rear axle hub and bearing assembly outside the rear axle hub bolt.

    Maximum runout:
    0.08 mm (0.0031 in.)

    NOTICE:
    Ensure that the dial indicator is set perpendicular to the measurement surface.

    HINT:
    If the runout exceeds the maximum, replace the rear axle hub and bearing assembly.


17. INSTALL REAR DISC

  1. C166438E01
    Align matchmarks and install the rear disc.

    NOTICE:
    When replacing the rear disc with a new one, select the installation position where the rear disc has minimal runout.


18. INSTALL REAR DISC BRAKE CALIPER ASSEMBLY

  1. C165996
    Install the rear disc brake caliper assembly with the 2 bolts.

    Torque:
    78 N*m{ 795 kgf*cm , 57 ft.*lbf }


19. INSTALL REAR AXLE SHAFT NUT

  1. C165541
    Using a chisel and a hammer, stake the rear axle shaft nut.


20. INSTALL REAR WHEEL

Torque:
103 N*m{ 1050 kgf*cm , 76 ft.*lbf }


21. INSPECT AND ADJUST REAR WHEEL ALIGNMENT

HINT:
Click here


22. CHECK FOR SPEED SENSOR SIGNAL

HINT:
Click here

← INSTALLATION (May 2007 – Jul 2008)INSTALLATION (from Jul 2010) →