2007-2013 Highlander Kluger · Service Manual SUSPENSION & AXLE

REMOVAL

Removal / installation · Vehicles built from Jul 2010

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010


1. REMOVE FRONT WHEEL

2. REMOVE FRONT AXLE HUB NUT

  1. C167528E01
    Using SST and a hammer, release the staked part of the front axle hub nut.
    SST
    09930-00010  

    NOTICE:
    Loosen the staked part of the nut completely, otherwise the threads of the drive shaft may be damaged.

  1. While applying the brakes, remove the front axle hub nut.


3. SEPARATE FRONT SPEED SENSOR

  1. C165818E03
    Remove the bolt and resin clamp, and separate the front speed sensor.


4. SEPARATE FRONT DISC BRAKE CALIPER ASSEMBLY

  1. C165913
    Remove the 2 bolts and separate the front disc brake caliper assembly.

    NOTICE:
    Use wire or an equivalent tool to keep the front disc brake caliper assembly from hanging down by the flexible hose.


5. REMOVE FRONT DISC

  1. C165879E01
    Remove the front disc.

    HINT:
    Put matchmarks on the disc and the axle hub.


6. SEPARATE TIE ROD ASSEMBLY
  1. Remove the cotter pin and the nut.

  1. C165542E01
    Install SST to the tie rod end.
    SST
    09960-20010   (09961-02060)

    NOTICE:
    Make sure that the upper ends of the tie rod end and SST are aligned.

  1. Using SST, separate the tie rod end from the steering knuckle.

    C165543E01

    SST
    09960-20010   (09961-02010)

    NOTICE:
    1. When securing SST to the steering knuckle, be sure to tighten the string of SST to prevent it from falling.
    1. Install SST so that A and B are parallel.
    1. Be sure to place the wrench on the part indicated in the illustration.
    1. Do not damage the front disc brake dust cover.
    1. Do not damage the ball joint dust cover.
    1. Do not damage the steering knuckle.


7. SEPARATE FRONT LOWER SUSPENSION ARM

  1. C165929
    Remove the bolt and 2 nuts, and separate the front lower suspension arm from the front lower ball joint.


8. SEPARATE FRONT DRIVE SHAFT ASSEMBLY

  1. C165537E05
    Put matchmarks on the front drive shaft assembly and the front axle hub sub-assembly.

    NOTICE:
    Do not punch the marks.

  1. C165534
    Using a plastic hammer, separate the front drive shaft assembly from the front axle assembly.

    NOTICE:
    Be careful not to damage the drive shaft boot and speed sensor rotor.


9. REMOVE FRONT AXLE ASSEMBLY

  1. C166269E01
    Remove the 2 bolts, 2 nuts and front axle assembly.

    NOTICE:
    When removing the nuts, keep the bolts from rotating.


10. REMOVE FRONT LOWER BALL JOINT

  1. C167239
    Secure the front axle assembly in a vise using aluminum plates.

    NOTICE:
    When using a vise, do not overtighten it.

  1. C165931
    Remove the cotter pin and nut.

  1. C165932E02
    Install SST to the front lower ball joint as shown in the illustration.
    SST
    09960-20010   (09961-02050, 09961-02050)

    NOTICE:
    Check that the clearance measurement between SST and the front axle assembly is 1 mm (0.04 in.).

  1. C165933E01
    Using SST, remove the front lower ball joint from the front axle assembly as shown in the illustration.
    SST
    09960-20010   (09961-02010, 09961-02050, 09961-02050)

    NOTICE:
    1. Install SST so that A and B are parallel.
    2. Be sure to place a wrench on the part indicated in the illustration.
    3. Do not damage the front lower ball joint dust cover.


11. REMOVE NO. 1 FRONT WHEEL BEARING DUST DEFLECTOR

  1. C166271E02
    Using a screwdriver with its tip wrapped with vinyl tape, remove the No. 1 front wheel bearing dust deflector.

    NOTICE:
    Be careful not to damage the steering knuckle.


12. REMOVE FRONT AXLE HUB HOLE SNAP RING

  1. C166270
    Using snap ring pliers, remove the front axle hub hole snap ring.


13. REMOVE FRONT AXLE HUB SUB-ASSEMBLY
  1. Hold the front axle assembly between aluminium plates in a vise.

    NOTICE:
    Do not overtighten the vise.

  1. C166272E01
    Using SST, remove the front axle hub sub-assembly.
    SST
    09520-00031  

  1. C167711E02
    Using SST and a press, remove the bearing inner race (outside) from the front axle hub sub-assembly.
    SST
    09555-55010  
    09950-60010   (09951-00430)
    09950-70010   (09951-07100)

    NOTICE:
    Be careful not to drop the front axle hub sub-assembly.


14. REMOVE FRONT DISC BRAKE DUST COVER

  1. C166273
    Remove the 4 bolts and front disc brake dust cover from the steering knuckle.


15. REMOVE STEERING KNUCKLE
  1. Place the bearing inner race (outside) on the front axle hub bearing.

  1. C168043E01
    Using SST, V-blocks and a press, remove the front axle hub bearing from the steering knuckle.
    SST
    09950-60010   (09951-00430, 09952-06010)
    09950-70010   (09951-07100)
    09950-60020   (09951-00750)

    NOTICE:
    Keep the steering knuckle level.

← REMOVAL (Aug 2008 – Jun 2010)INSTALLATION (May 2007 – Jul 2008) →