2007-2013 Highlander Kluger · Service Manual ENGINE

DISASSEMBLY

Removal / installation · Vehicles built from May 2007


1. REMOVE PISTON SUB-ASSEMBLY WITH CONNECTING ROD
  1. Check that the matchmarks on the connecting rod sub-assembly and connecting rod cap are aligned.

    HINT:
    The matchmarks on the connecting rod sub-assembly and connecting rod cap are guides for the correct reassembly.

  1. A129760E01
    Remove the 2 connecting rod cap bolts.

  1. A129761
    Using the 2 removed connecting rod cap bolts, remove the connecting rod cap and lower bearing by wiggling the connecting rod cap right and left.

    HINT:
    Keep the lower bearing inserted to the connecting rod cap.

  1. A129720E01
    Using a ridge reamer, remove all the carbon from the top of the cylinder.

  1. Push the piston, connecting rod assembly and upper bearing through the top of the cylinder block.

    HINT:
    1. Keep the bearing, connecting rod and cap together.
    2. Arrange the piston and connecting rod assemblies in the correct order.


2. REMOVE CONNECTING ROD BEARING

HINT:
Arrange the removed parts in the correct order.


3. REMOVE PISTON RING SET

  1. A129724E01
    Using a piston ring expander, remove the 2 compression rings.

  1. Remove the oil ring expander and 2 side rails by hand.

    HINT:
    Arrange the removed parts in the correct order.


4. REMOVE PISTON SUB-ASSEMBLY WITH PIN

  1. A129725
    Check the fitting condition between the piston and piston pin.

    1. Try to move the piston back and forth on the piston pin.
      If any movement is felt, replace the piston and pin as a set.

  1. A129726
    Disconnect the connecting rod from the piston.

    1. Using a screwdriver, pry off the piston pin hole snap rings from the piston.

    2. A109729
      Gradually heat the piston to approximately 80°C (176°F).

    3. A129728
      Using a brass bar and plastic hammer, lightly tap out the piston pin and remove the connecting rod sub-assembly.

      HINT:
      1. The piston and piston pin are a matched set.
      2. Arrange the pistons, piston pins, piston pin hole snap rings, connecting rods and connecting rod bearings in the correct order.

  1. A129729
    Using a gasket scraper, remove the carbon from the piston top.

  1. A129730
    Using a groove cleaning tool or broken ring, clean the piston ring grooves.

  1. A129731
    Using solvent and a brush, thoroughly clean the piston.

    NOTICE:
    Do not use a wire brush.


5. REMOVE CRANKSHAFT

  1. A129721E03
    Uniformly loosen and remove the 8 crankshaft bearing cap bolts and the 8 seal washers in several steps and in the sequence shown in the illustration.

  1. A134892E01
    Uniformly loosen the 16 crankshaft bearing cap bolts, in several steps and in the sequence shown in the illustration.

  1. A122567E01
    Using a screwdriver, pry out the crankshaft bearing caps. Remove the 4 crankshaft bearing caps and lower crankshaft bearings.

    NOTICE:
    1. Push up on the cap slowly and evenly, alternating from the right and left side so that the bearing cap can be removed.
    2. Be careful not to damage the joint surface of the cylinder block and the crankshaft bearing cap.

  1. Remove the crankshaft.


6. REMOVE CRANKSHAFT BEARING
  1. Remove the upper crankshaft bearing and lower crankshaft bearing.

    HINT:
    Arrange the removed parts in the correct order.


7. REMOVE CRANKSHAFT THRUST WASHER SET

  1. A109726
    Remove the upper crankshaft bearings and upper crankshaft thrust washers from the cylinder block sub-assembly.


8. REMOVE NO. 1 OIL NOZZLE SUB-ASSEMBLY

  1. A120734
    Using a 5 mm hexagon wrench, remove the bolts and No. 1 oil nozzle sub-assembly.

  1. Check the 3 oil nozzles for damage or clogging.
    If necessary, replace the No. 1 oil nozzle sub-assembly.


9. CLEAN CYLINDER BLOCK
← COMPONENTS (from May 2007)INSPECTION (from May 2007) →