2007-2013 Highlander Kluger · Service Manual ENGINE

DISASSEMBLY

Removal / installation · Vehicles built from Aug 2013

Versions by build date: May 2007 – Jun 2010 Jul 2010 – Jul 2013 from Aug 2013


1. REMOVE OIL FILLER CAP SUB-ASSEMBLY
  1. Remove the oil filler cap sub-assembly and oil filler gasket.


2. REMOVE SPARK PLUG
  1. Remove the spark plugs.


3. REMOVE OIL PAN DRAIN PLUG

  1. A129654
    Remove the oil pan drain plug and oil pan drain plug gasket.


4. REMOVE VENTILATION VALVE SUB-ASSEMBLY

  1. A129655
    Remove the ventilation valve sub-assembly.


5. REMOVE CAMSHAFT POSITION SENSOR

  1. A129656E04
    Remove the 4 bolts and 4 camshaft position sensors.


6. REMOVE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY

  1. A129662E06
    Remove the 4 bolts and 4 camshaft timing oil control valves.


7. REMOVE CRANKSHAFT POSITION SENSOR

  1. A129663
    Remove the bolt and crankshaft position sensor.


8. REMOVE NO. 1 OIL PIPE

  1. A135726E01
    Remove the 2 oil pipe unions, gaskets and No. 1 oil pipe.

  1. Remove the oil control valve filter LH and gaskets.


9. REMOVE OIL PIPE

  1. A200607E16
    Remove the bolt.

  1. Remove the 2 oil pipe unions and oil pipe.

  1. Remove the oil control valve filter RH and gaskets.


10. REMOVE TAPER SCREW PLUG

HINT:
Perform this operation only when a taper screw plug is installed.

  1. A292824
    Remove the taper screw plug from the cylinder block sub-assembly.


11. REMOVE CYLINDER BLOCK WATER DRAIN COCK SUB-ASSEMBLY

  1. A305214E04
    for Bank 1:

    1. Remove the cylinder block water drain cock sub-assembly from the cylinder block sub-assembly.

    2. Remove the cylinder block water drain cock plug from the cylinder block water drain cock sub-assembly.

  1. for Bank 2:

    HINT:
    Perform this operation only when a cylinder block water drain cock sub-assembly is installed.


    1. Remove the cylinder block water drain cock sub-assembly from the cylinder block sub-assembly.

    2. Remove the cylinder block water drain cock plug from the cylinder block water drain cock sub-assembly.


12. REMOVE OIL FILTER ELEMENT

  1. A129666
    Remove the drain plug.

    NOTICE:
    Do not remove the O-ring from the oil filter cap sub-assembly.

  1. A129667E01
    Connect the hose to the pipe.

  1. Insert the pipe with hose into the oil filter cap sub-assembly.

  1. Make sure that the oil is completely drained and remove the pipe and O-ring.

  1. A129668E01
    Using SST, remove the oil filter cap sub-assembly.
    SST
    09228-06501  

  1. A106167E06
    Remove the oil filter element and O-ring from the oil filter cap sub-assembly.

    NOTICE:
    Do not use any tools when removing the O-ring to prevent the O-ring groove from being damaged.


13. REMOVE CRANKSHAFT PULLEY

  1. A120690E02
    Using SST, loosen the crankshaft pulley bolt.
    SST
    09213-70011   (09213-70020)
    09330-00021  

  1. A120691E02
    Using SST, remove the crankshaft pulley bolt and crankshaft pulley.
    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05020, 09954-05021)


14. REMOVE OIL COOLER ASSEMBLY

  1. A136291
    Remove the bolt, 2 clamps and 4 clips, and disconnect the 2 water by-pass hoses.

  1. A136292
    Remove the union bolt, oil cooler assembly, and O-ring.


15. REMOVE NO. 1 OIL COOLER BRACKET

  1. A268434
    Remove the 3 bolts, 3 nuts, and oil cooler pipe with No. 1 oil cooler bracket.

  1. A268435E03
    Remove the bolt, 2 nuts, No. 1 oil cooler bracket, and gasket.

  1. Using an E8 "TORX" socket wrench, remove the 2 stud bolts.

  1. Using an E7 "TORX" socket wrench, remove the stud bolt.


16. REMOVE NO. 1 ENGINE OIL LEVEL DIPSTICK GUIDE
  1. Remove the No. 1 engine oil level dipstick guide.

  1. A171897
    Remove the O-ring.


17. REMOVE NO. 1 FRONT ENGINE MOUNTING BRACKET LH

  1. A129672
    Remove the 6 bolts and No. 1 front engine mounting bracket LH.

  1. Using an E8 "TORX" socket wrench, remove the 2 stud bolts.


18. REMOVE WATER INLET HOUSING

  1. A129673
    Remove the 2 nuts, water inlet and thermostat.

  1. Remove the gasket.

  1. Remove the 2 stud bolts.

  1. Separate the No. 1 water by-pass hose from the water inlet housing.

  1. A134879E01
    Remove the drain cock plug.

  1. Remove the drain cock assembly.

  1. Remove the 2 bolts, nut, and water inlet housing.

  1. A129675
    Remove the 2 O-rings.


19. REMOVE WATER OUTLET

  1. A129676E01
    Remove the 2 bolts, 4 nuts and water outlet.

  1. A129677
    Remove the 2 gaskets and O-ring.


20. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY (for Bank 1)

  1. A129679
    Remove the 12 bolts, seal washer, cylinder head cover sub-assembly and cylinder head cover gasket.

  1. A129699
    Remove the 3 gaskets.


21. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY (for Bank 2)

  1. A129678E02
    Remove the 12 bolts, seal washer, cylinder head cover sub-assembly and cylinder head cover gasket.

    NOTICE:
    The baffle plate is located on the back of the portion shown in the illustration. Do not damage the baffle plate when removing the cylinder head cover sub-assembly.

  1. A129705
    Remove the 3 gaskets.


22. REMOVE NO. 2 OIL PAN SUB-ASSEMBLY

  1. A129680E01
    Remove the 16 bolts and 2 nuts.

  1. A120816
    Insert the blade of an oil pan seal cutter between the oil pans. Cut through the applied sealer and remove the No. 2 oil pan sub-assembly.

    NOTICE:
    Be careful not to damage the contact surfaces of the oil pans.

  1. Using an E6 "TORX" socket wrench, remove the 2 stud bolts.


23. REMOVE OIL STRAINER SUB-ASSEMBLY

  1. A129681
    Remove the bolt, 2 nuts, oil strainer sub-assembly and gasket.

  1. Using an E6 "TORX" socket wrench, remove the 2 stud bolts.


24. REMOVE OIL PAN SUB-ASSEMBLY

  1. A242991E01
    Remove the 16 bolts and 2 nuts.

    HINT:
    Be sure to clean the bolts and stud bolts and check the threads for cracks or other damage.

  1. A129683E01
    Remove the oil pan sub-assembly by prying between the oil pan sub-assembly and cylinder block sub-assembly with a screwdriver.

    NOTICE:
    Be careful not to damage the contact surfaces of the cylinder block sub-assembly and oil pan sub-assembly.

    HINT:
    Tape the screwdriver tip before use.

  1. A129684
    Remove the 2 O-rings.

  1. Using an E8 "TORX" socket wrench, remove the 2 stud bolts.


25. REMOVE NO. 1 OIL PAN BAFFLE PLATE

  1. A129685
    Remove the 7 bolts and No. 1 oil pan baffle plate.


26. REMOVE ENGINE REAR OIL SEAL RETAINER

  1. A129686
    Remove the 6 bolts.

  1. A129687E03
    Using a screwdriver, pry out the engine rear oil seal retainer.

    NOTICE:
    Be careful not to damage the engine rear oil seal retainer.

    HINT:
    Tape the screwdriver tip before use.


27. REMOVE ENGINE REAR OIL SEAL

  1. A131834E12
    Place the engine rear oil seal retainer on wooden blocks.

    NOTICE:
    Be careful not to damage the engine rear oil seal retainer.

  1. Using a screwdriver and a hammer, tap out the engine rear oil seal.

    HINT:
    Tape the screwdriver tip before use.


28. REMOVE WATER PUMP ASSEMBLY

  1. A129688
    Remove the 16 bolts, water pump assembly and water pump gasket.


29. REMOVE TIMING CHAIN COVER SUB-ASSEMBLY

  1. A129689E01
    Remove the 15 bolts and 2 nuts as shown in the illustration.

  1. A129690E02
    Remove the timing chain cover sub-assembly by prying between the timing chain cover sub-assembly and cylinder head sub-assembly or cylinder block sub-assembly with a screwdriver.

    NOTICE:
    Be careful not to damage the contact surfaces of the cylinder head sub-assembly, cylinder block sub-assembly and timing chain cover sub-assembly.

    HINT:
    Tape the screwdriver tip before use.

  1. Remove the 4 bolts, chain cover plate and chain cover plate gasket.

  1. A128006E01
    Remove the gasket.


30. REMOVE TIMING CHAIN CASE OIL SEAL

  1. A108818E01
    Using a screwdriver, pry out the timing chain case oil seal.

    HINT:
    Tape the screwdriver tip before use.


31. SET NO. 1 CYLINDER TO TDC / COMPRESSION
  1. Temporarily tighten the pulley set bolt.

  1. A129691E12
    Set the timing mark on the crank angle sensor plate to the RH block bore center line (TDC / compression).

  1. A129692E10
    Check that the timing marks of the camshaft timing gears are aligned with those of the bearing cap as shown in the illustration.
    If not, turn the crankshaft 1 revolution (360°) and align the timing marks as shown in the illustration.


32. REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY

  1. A124589E13
    Move the stopper plate upward to release the lock, and push the plunger deep into the tensioner.

  1. Move the stopper plate downward to set the lock, and insert a hexagon wrench into the stopper plate's hole.

  1. A095165
    Remove the 2 bolts and No. 1 chain tensioner assembly.


33. REMOVE CHAIN TENSIONER SLIPPER
  1. Remove the chain tensioner slipper.


34. REMOVE CHAIN SUB-ASSEMBLY

  1. A134897E02
    Turn the crankshaft counterclockwise 10° to loosen the chain sub-assembly.

  1. Remove the pulley set bolt.

  1. A134890
    Remove the chain sub-assembly from the crankshaft timing sprocket and place it on the crankshaft.

  1. A095682E05
    Turn the camshaft timing gear assembly on bank 1 clockwise (approximately 60°) and set it as shown in the illustration. Be sure to loosen the chain sub-assembly between the banks.

  1. Remove the chain sub-assembly.


35. REMOVE IDLE SPROCKET ASSEMBLY

  1. A129695
    Using a 10 mm hexagon wrench, remove the No. 2 idle gear shaft, idle sprocket assembly and No. 1 idle gear shaft.


36. REMOVE NO. 1 CHAIN VIBRATION DAMPER

  1. A129696
    Remove the 2 bolts and No. 1 chain vibration damper.


37. REMOVE NO. 2 CHAIN VIBRATION DAMPER
  1. Remove the 2 No. 2 chain vibration dampers.


38. REMOVE CRANKSHAFT TIMING SPROCKET

  1. A109720
    Remove the crankshaft timing sprocket from the crankshaft.

  1. Remove the 2 keys from the crankshaft.


39. REMOVE CAMSHAFT TIMING GEARS AND NO. 2 CHAIN SUB-ASSEMBLY (for Bank 1)

  1. A120651E03
    While raising the No. 2 chain tensioner assembly, insert a pin of 1.0 mm diameter (0.039 in.) into the hole to fix the No. 2 chain tensioner assembly.

  1. A120652E01
    Hold the hexagonal portion of the camshaft with a wrench, and remove the 2 bolts and 2 camshaft timing gear assemblies.

    NOTICE:
    1. Be careful not to damage the cylinder head sub-assembly RH with the wrench.
    2. Do not disassemble the camshaft timing gear assemblies.

  1. Remove the No. 2 chain sub-assembly.


40. REMOVE NO. 2 CHAIN TENSIONER ASSEMBLY

  1. A109721
    Remove the bolt and No. 2 chain tensioner assembly.


41. REMOVE CAMSHAFT BEARING CAP (for Bank 1)

  1. A129700E01
    Check that the camshafts are positioned as shown in the illustration.

  1. A129701E03
    Uniformly loosen and remove the 8 bearing cap bolts in several steps and in the sequence shown in the illustration.

  1. A129702E01
    Uniformly loosen and remove the 12 bearing cap bolts in several steps in the sequence shown in the illustration.

    NOTICE:
    Uniformly loosen the bolts while keeping the camshafts level.

  1. Remove the 5 camshaft bearing caps.


42. REMOVE CAMSHAFT
  1. Remove the camshaft.


43. REMOVE NO. 2 CAMSHAFT
  1. Remove the No. 2 camshaft.


44. REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY RH

  1. A129703E01
    Remove the camshaft housing sub-assembly RH by prying between the cylinder head sub-assembly RH and camshaft housing sub-assembly RH with a screwdriver.

    NOTICE:
    Be careful not to damage the contact surfaces of the cylinder head sub-assembly RH and camshaft housing sub-assembly RH.

    HINT:
    Tape the screwdriver tip before use.


45. REMOVE CAMSHAFT TIMING GEARS AND NO. 2 CHAIN SUB-ASSEMBLY (for Bank 2)

  1. A120657E01
    While pushing down the No. 3 chain tensioner assembly, insert a pin of 1.0 mm diameter (0.039 in.) into the hole to fix the No. 3 chain tensioner assembly.

  1. A120658E01
    Hold the hexagonal portion of the camshaft with a wrench, and remove the 2 bolts and 2 camshaft timing gear assemblies.

    NOTICE:
    1. Be careful not to damage the cylinder head sub-assembly LH with the wrench.
    2. Do not disassemble the camshaft timing gear assemblies.

  1. Remove the No. 2 chain sub-assembly.


46. REMOVE NO. 3 CHAIN TENSIONER ASSEMBLY

  1. A109722
    Remove the bolt and No. 3 chain tensioner assembly.


47. REMOVE CAMSHAFT BEARING CAP (for Bank 2)

  1. A129706E01
    Check that the camshafts are positioned as shown in the illustration.

  1. A134891E03
    Uniformly loosen and remove the 8 bearing cap bolts in several steps and in the sequence shown in the illustration.

  1. A129708E01
    Uniformly loosen and remove the 13 bearing cap bolts in several steps and in the sequence shown in the illustration.

    NOTICE:
    Uniformly loosen the bolts while keeping the camshafts level.

  1. Remove the 5 camshaft bearing caps.


48. REMOVE NO. 3 CAMSHAFT
  1. Remove the No. 3 camshaft.


49. REMOVE NO. 4 CAMSHAFT
  1. Remove the No. 4 camshaft.


50. REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY LH

  1. A129709E01
    Remove the camshaft housing sub-assembly LH by prying between the cylinder head sub-assembly LH and camshaft housing sub-assembly LH with a screwdriver.

    NOTICE:
    Be careful not to damage the contact surfaces of the cylinder head sub-assembly LH and camshaft housing sub-assembly LH.

    HINT:
    Tape the screwdriver tip before use.


51. REMOVE NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY
  1. Remove the 24 No. 1 valve rocker arm sub-assemblies.

    HINT:
    Arrange the removed parts in the correct order.


52. REMOVE VALVE LASH ADJUSTER ASSEMBLY
  1. Remove the 24 valve lash adjuster assemblies from the 2 cylinder head sub-assemblies.

    HINT:
    Arrange the removed parts in the correct order.


53. REMOVE CYLINDER HEAD SUB-ASSEMBLY RH

  1. A129712E01
    Using a 10 mm bi-hexagon wrench, uniformly loosen the 8 cylinder head bolts in the sequence shown in the illustration. Remove the 8 cylinder head bolts and plate washers.

    NOTICE:
    1. Be careful not to drop plate washers into the cylinder head sub-assembly RH.
    2. Cylinder head warpage or cracking could result from removing bolts in an incorrect order.

    HINT:
    Be sure to keep separate the removed parts for each installation position.

  1. Remove the cylinder head sub-assembly RH and cylinder head gasket.


54. REMOVE CYLINDER HEAD SUB-ASSEMBLY LH

  1. A129710E01
    Uniformly loosen and remove the 2 cylinder head set bolts in several steps and in the sequence shown in the illustration.

  1. A129711E01
    Using a 10 mm bi-hexagon wrench, uniformly loosen the 8 cylinder head bolts in the sequence shown in the illustration. Remove the 8 cylinder head bolts and plate washers.

    NOTICE:
    1. Be careful not to drop plate washers into the cylinder head sub-assembly LH.
    2. Cylinder head warpage or cracking could result from removing bolts in an incorrect order.

    HINT:
    Be sure to keep separate the removed parts for each installation position.

  1. Remove the cylinder head sub-assembly LH and No. 2 cylinder head gasket.


55. REMOVE WATER INLET PIPE
  1. Remove 2 clamps and separate the No. 1 water by-pass hose.

  1. A242992
    Remove the 2 bolts and water inlet pipe.

← DISASSEMBLY (Jul 2010 – Jul 2013)INSPECTION (May 2007 – Jul 2008) →