2007-2013 Highlander Kluger · Service Manual ENGINE

REASSEMBLY

Removal / installation · Vehicles built Jul 2010 – Jun 2012

Versions by build date: May 2007 – Jun 2010 Jul 2010 – Jun 2012 Jul 2012 – Jul 2013 from Aug 2013


1. INSTALL ENGINE REAR OIL SEAL
  1. Place the oil seal retainer on wooden blocks.

  1. A120675E01
    Using SST, tap in a new engine rear oil seal until its surface is flush with the engine rear oil seal retainer edge.
    SST
    09223-15030  
    09950-70010   (09951-07100)

    NOTICE:
    1. Keep the lip free of foreign matter.
    2. Do not tap on the engine rear oil seal at an angle.


2. INSTALL ENGINE REAR OIL SEAL RETAINER

  1. A141351E04
    Apply seal packing in a continuous line as shown in the illustration.

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    Seal diameter:
    2.0 to 3.0 mm (0.079 to 0.118 in.)

    NOTICE:
    1. Remove any oil from the contact surfaces.
    2. Install the oil seal retainer within 3 minutes after applying seal packing.
    3. Do not start the engine for at least 2 hours after installation.

  1. A129686E01
    Install the engine rear oil seal retainer with the 6 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

    NOTICE:
    Be sure to apply adhesive 1324 to the bolts in the places indicated by A before installing them.

    Adhesive:
    Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent


3. INSTALL WATER INLET PIPE

  1. A242992
    Install the water inlet pipe with the 2 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

  1. Install the No. 1 water by-pass hose.


4. INSTALL CYLINDER HEAD SUB-ASSEMBLY RH

  1. A131898E01
    Place the cylinder head gasket on the cylinder block surface with the Lot No. stamp upward.

    NOTICE:
    1. Be careful of the installation direction.
    2. Gently lower the cylinder head in order not to damage the gasket with the bottom part of the head.

  1. Place the cylinder head on the cylinder block.

    NOTICE:
    Be careful not to allow oil to adhere to the bottom part of the cylinder head.

    HINT:
    The cylinder head bolts are tightened in 3 progressive steps.

  1. Apply a light coat of engine oil to the threads and under the heads of the cylinder head bolts.

  1. Step 1

    1. A129712E02
      Using a 10 mm bi-hexagon wrench, install and uniformly tighten the 8 cylinder head bolts with the plate washers in several steps and in the sequence shown in the illustration.

      Torque:
      36 N*m{ 367 kgf*cm , 27 ft.*lbf }

  1. A035289E02
    Step 2

    1. Mark the cylinder head bolt head with paint as shown in the illustration.

    2. Tighten the cylinder head bolts another 90°.

  1. Step 3

    1. Tighten the cylinder head bolts an additional 90°.

    2. Check that the painted mark is now facing rearward.


5. INSTALL CYLINDER HEAD SUB-ASSEMBLY LH

  1. A131900E01
    Place the cylinder head gasket on the cylinder block surface with the Lot No. stamp upward.

    NOTICE:
    1. Be careful of the installation direction.
    2. Gently lower the cylinder head in order not to damage the gasket with the bottom part of the head.

  1. Place the cylinder head on the cylinder block.

    NOTICE:
    Be careful not to allow oil to adhere to the bottom part of the cylinder head.

    HINT:
    The cylinder head bolts are tightened in 3 progressive steps.

  1. Apply a light coat of engine oil to the threads and under the heads of the cylinder head bolts.

  1. Step 1

    1. A129711E02
      Using a 10 mm bi-hexagon wrench, install and uniformly tighten the 8 cylinder head bolts with the plate washers in several steps in the sequence shown in the illustration.

      Torque:
      36 N*m{ 367 kgf*cm , 27 ft.*lbf }

  1. A035289E02
    Step 2

    1. Mark the cylinder head bolt head with paint as shown in the illustration.

    2. Tighten the cylinder head bolts another 90°.

  1. Step 3

    1. Tighten the cylinder head bolts an additional 90°.

    2. Check that the painted mark is now facing rearward.

  1. A129710E02
    Tighten the 2 bolts in the order shown in the illustration.

    Torque:
    30 N*m{ 306 kgf*cm , 22 ft.*lbf }


6. INSTALL VALVE LASH ADJUSTER ASSEMBLY

NOTICE:
  1. Keep the lash adjuster free of dirt and foreign objects.
  2. Only use clean engine oil.

  1. Place the lash adjuster into a container filled with engine oil.

  1. A109630E06
    Insert SST's tip into the lash adjuster's plunger and use the tip to press down on the check ball inside the plunger.
    SST
    09276-75010  

  1. Squeeze SST and lash adjuster together to move the plunger up and down 5 to 6 times.

  1. Check the movement of the plunger and bleed the air.

    OK:
    Plunger moves up and down.

    NOTICE:
    When bleeding air from the high-pressure chamber, make sure that the tip of SST is actually pressing the check ball as shown in the illustration. If the check ball is not pressed, air will not bleed.

  1. After bleeding the air, remove SST. Then, try to press the plunger quickly and firmly with by hand.

    OK:
    Plunger is very difficult to move.

    If the result is not as specified, replace the lash adjuster.

  1. Install the lash adjusters.

    NOTICE:
    Install the lash adjuster to the same place where it was removed from.


7. INSTALL NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY
  1. Apply engine oil to the lash adjuster tip and valve stem cap end.

  1. A131901E03
    Make sure that the 24 No. 1 valve rocker arms are installed as shown in the illustration.


8. INSTALL CAMSHAFT BEARING CAP (for Bank 1)
  1. Apply engine oil to the camshaft journals, camshaft housing sub-assembly RH and camshaft bearing caps.

  1. Install the camshaft and No. 2 camshaft to the camshaft housing sub-assembly RH.

  1. A131902
    Make sure to install camshaft bearing caps in each proper position and direction according to the painted marks and numbers.

  1. A131903E01
    Temporarily tighten the 8 bearing cap bolts in the order shown in the illustration.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }


9. INSTALL CAMSHAFT HOUSING SUB-ASSEMBLY RH

  1. A131901E01
    Make sure that the No. 1 valve rocker arm sub-assembly is installed as shown in the illustration.

  1. A131904E04
    Apply seal packing in a continuous line as shown in the illustration.

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    Seal diameter:
    3.5 to 4.5 mm (0.138 to 0.177 in.)

    NOTICE:
    1. Remove any oil from the contact surfaces.
    2. Install the camshaft housing sub-assembly RH within 3 minutes.
    3. Do not start the engine for at least 2 hours after installing.

  1. A131905E01
    Install the camshaft housing sub-assembly RH and tighten the 12 bolts in the order shown in the illustration.

    Torque:
    28 N*m{ 286 kgf*cm , 21 ft.*lbf }

    NOTICE:
    1. When installing the camshaft housing RH, it is necessary to correctly position the camshafts as shown in the illustration. Failure to correctly position these parts may result in damage due to contact between the pistons and valves. If a camshaft is rotated with a piston at TDC, valve contact will occur.
    2. If any of the bolts are loosened during installation, remove the camshaft housing, clean the installation surfaces, and reapply seal packing.
    3. If the camshaft housing sub-assembly is removed because any of the bolts are loosened during installation, make sure that the previously applied seal packing does not enter any oil passages.

  1. A129701E02
    Tighten the 8 bolts in the order shown in the illustration.

    Torque:
    16 N*m{ 163 kgf*cm , 12 ft.*lbf }


10. INSTALL CAMSHAFT BEARING CAP (for Bank 2)
  1. Apply engine oil to the camshaft journals, camshaft housing sub-assembly LH and camshaft bearing caps.

  1. Install the No. 3 camshaft and No. 4 camshaft to the camshaft housing sub-assembly LH.

  1. A134960
    Make sure to install camshaft bearing caps in each proper position and direction according to the painted marks and numbers.

  1. A132217E01
    Temporarily tighten the 8 bolts in the order shown in the illustration.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }


11. INSTALL CAMSHAFT HOUSING SUB-ASSEMBLY LH

  1. A131901E05
    Make sure that the valve rocker arm is installed as shown in the illustration.

  1. A132218E05
    Apply seal packing in a continuous line as shown in the illustration.

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    Seal diameter:
    3.5 to 4.5 mm (0.138 to 0.177 in.)

    NOTICE:
    1. Remove any oil from the contact surface.
    2. Install the camshaft housing sub-assembly LH within 3 minutes.
    3. Do not start the engine for at least 2 hours after installing.

  1. A132219E01
    Install the camshaft housing sub-assembly LH and tighten the 13 bolts in the order shown in the illustration.

    Torque:
    28 N*m{ 286 kgf*cm , 21 ft.*lbf }

    NOTICE:
    1. When installing the camshaft housing LH, it is necessary to correctly position the camshafts as shown in the illustration. Failure to correctly position these parts may result in damage due to contact between the pistons and valves. If a camshaft is rotated with a piston at TDC, valve contact will occur.
    2. If any of the bolts are loosened during installation, remove the camshaft housing, clean the installation surfaces, and reapply seal packing.
    3. If the camshaft housing is removed because any of the bolts are loosened during installation, make sure that the previously applied seal packing does not enter any oil passages.

  1. A134891E02
    Tighten the 8 bolts in the order shown in the illustration.

    Torque:
    16 N*m{ 163 kgf*cm , 12 ft.*lbf }


12. INSTALL NO. 2 CHAIN TENSIONER ASSEMBLY

  1. A121265E02
    Install the No. 2 chain tensioner assembly with the bolt.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

  1. While pushing in the tensioner, insert a pin of 1.0 mm (0.039 in.) diameter into the hole to fix it.


13. INSTALL CAMSHAFT TIMING GEARS AND NO. 2 CHAIN (for Bank 1)

  1. A124048E09
    Align the mark plate (yellow) with the timing marks (1-dot mark) of the camshaft timing gear assemblies as shown in the illustration.

  1. Apply a light coat of engine oil to the bolt threads and bolt-seating surface.

  1. Align the knock pin of the camshaft with the pin hole of the camshaft timing gear assembly. Install the camshaft timing gear assembly and camshaft timing exhaust gear RH with the No. 2 chain sub-assembly installed.

  1. A121640E01
    Hold the hexagonal portion of the camshaft with a wrench, and tighten the 2 bolts and camshaft timing gear assemblies.

    Torque:
    100 N*m{ 1020 kgf*cm , 74 ft.*lbf }

  1. Remove the pin from the No. 2 chain tensioner assembly.


14. INSTALL NO. 3 CHAIN TENSIONER ASSEMBLY

  1. A121266E02
    Install the No. 3 chain tensioner assembly with the bolt.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

  1. While pushing in the tensioner, insert a pin of 1.0 mm diameter (0.039 in.) into the hole to hold it.


15. INSTALL CAMSHAFT TIMING GEARS AND NO. 2 CHAIN (for Bank 2)

  1. A124049E06
    Align the mark plate (yellow) with the timing marks (2-dot mark) of the camshaft timing gear assemblies as shown in the illustration.

  1. Apply a light coat of engine oil to the bolt threads and bolt-seating surface.

  1. Align the knock pin of the camshaft with the pin hole of the camshaft timing gear assembly. Install the camshaft timing gear assembly and camshaft timing exhaust gear LH with the No. 2 chain sub-assembly installed.

  1. A121641E02
    Hold the hexagonal portion of the camshaft with a wrench, and tighten the 2 bolts.

    Torque:
    100 N*m{ 1020 kgf*cm , 74 ft.*lbf }

  1. Remove the pin from the No. 3 chain tensioner assembly.


16. INSTALL NO. 1 CHAIN VIBRATION DAMPER

  1. A120649
    Install the No. 1 chain vibration damper with the 2 bolts.

    Torque:
    23 N*m{ 230 kgf*cm , 17 ft.*lbf }


17. INSTALL NO. 2 CHAIN VIBRATION DAMPER
  1. Install the 2 No. 2 chain vibration dampers.


18. INSTALL CRANKSHAFT TIMING SPROCKET

  1. A109720
    Install the 2 keys and crankshaft timing sprocket as shown in the illustration.


19. INSTALL IDLE SPROCKET ASSEMBLY

  1. A132222E01
    Apply a light coat of engine oil to the rotating surface of the No. 1 idle gear shaft.

  1. Temporarily install the No. 1 idle gear shaft and idle sprocket with the No. 2 idle gear shaft while aligning the knock pin of the No. 1 idle gear shaft with the knock pin groove of the cylinder block.

    NOTICE:
    Be careful of the idle gear installation position.

    HINT:
    Check that no foreign objects are on the No. 1 and No. 2 idle gear shafts.

  1. Using a 10 mm hexagon wrench, tighten the No. 2 idle gear shaft.

    Torque:
    60 N*m{ 612 kgf*cm , 44 ft.*lbf }

    HINT:
    After installing the idle sprocket assembly, check that the idle sprocket turns smoothly.


20. INSTALL CHAIN SUB-ASSEMBLY

  1. A132223E02
    Align the mark plate and timing marks as shown in the illustration and install the chain.

    HINT:
    The camshaft mark plates are orange.

  1. A134890
    Do not pass the chain over the crankshaft, just temporaily place it on the crankshaft.

  1. A122184E04
    Turn the camshaft timing gear assembly on bank 1 counterclockwise to tighten the chain between the banks.

    NOTICE:
    When the idle sprocket assembly is reused, align the chain plate with the mark where the plate had been in order to tighten the chain between the banks.

  1. A132224E03
    Align the mark plate and timing marks as shown in the illustration and install the chain onto the crankshaft timing sprocket.

    HINT:
    The crankshaft mark plate is yellow.

  1. Temporarily tighten the pulley set bolt.

  1. A129691E04
    Turn the crankshaft clockwise to set it to the RH block bore center line (TDC/compression).


21. INSTALL CHAIN TENSIONER SLIPPER
  1. Install the chain tensioner slipper.


22. INSTALL NO. 1 CHAIN TENSIONER ASSEMBLY

  1. A132225E01
    Move the stopper plate upward to release the lock, and push the plunger deep into the tensioner.

  1. Move the stopper plate downward to set the lock, and insert a hexagon wrench into the hole of the stopper plate.

  1. A095165
    Install the No. 1 chain tensioner assembly with the 2 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

  1. A134895E05
    Remove the hexagon wrench from the No. 1 chain tensioner assembly. Check that each timing mark is aligned with the crankshaft at the TDC/compression.

  1. Remove the pulley set bolt.


23. INSTALL TIMING CHAIN CASE OIL SEAL

  1. A125109E04
    Using SST, tap in a new timing chain case oil seal until its surface is flush with the timing gear case edge.
    SST
    09223-22010  
    09506-35010  

    NOTICE:
    1. Keep the lip free of foreign matter.
    2. Do not tap on the oil seal at an angle.
    3. Make sure that the oil seal edge does not stick out of the timing chain case.


24. INSTALL WATER PUMP ASSEMBLY

  1. A132227E03
    Install a new water pump gasket and the water pump assembly with the 8 bolts.

    Torque:
    9.1 N*m{ 93 kgf*cm , 81 in.*lbf }

    NOTICE:
    Be sure to replace the bolts indicated by A with new ones or reuse them after applying adhesive 1344.


25. INSTALL TIMING CHAIN COVER SUB-ASSEMBLY

  1. Apply seal packing in a continuous line to the engine unit as shown in the following illustration.

    A132228E01

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    Seal diameter:
    3.0 mm (0.118 in.)

    NOTICE:
    1. Be sure to clean and degrease the contact surfaces, especially the surfaces indicated by C in the illustration.
    2. If the contact surfaces are wet, wipe them with an oil-free cloth before applying seal packing.
    3. Install the chain cover within 3 minutes.
    4. Do not start the engine for at least 2 hours after installing.

  1. Apply seal packing in a continuous line to the timing chain cover as shown in the following illustration.

    A134901E13

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent
    Toyota Genuine Seal Packing 1282B, Three Bond 1282B or equivalent

    NOTICE:
    1. If the contact surfaces are wet, wipe them with an oil-free cloth before applying seal packing.
    2. Install the chain cover within 3 minutes and tighten the bolts within 15 minutes after applying seal packing.
    3. Do not start the engine for at least 2 hours after installing.


    Apply seal packing as follows:
    Area
    Seal Packing Diameter
    Application Position from Inside Seal Line
    Continuous Line Area
    4.5 mm or more (0.177 in.)
    3.0 to 4.0 mm (0.118 to 0.158 in.)
    Alternate Long and Dashed Line Area
    3.5 mm or more (0.138 in.)
    2.0 to 3.0 mm (0.079 to 0.118 in.)
    Dashed Line Area
    3.5 mm or more (0.138 in.)
    3.0 to 4.0 mm (0.118 to 0.158 in.)
    Diagonal Line Area
    6.0 mm or more (0.236 in.)
    5.0 mm (0.197 in.)

  1. A128017E01
    Install a new gasket.

  1. A132229E04
    Align the oil pump's drive rotor spline and the crankshaft as shown in the illustration. Install the spline and chain cover to the crankshaft.

  1. Temporarily tighten the timing chain cover with the 23 bolts and 2 nuts.

    A128019E05

    Bolt length:
    Item
    Length
    Bolt A
    40 mm (1.57 in.)
    Bolt B
    55 mm (2.17 in.)
    Bolt C
    25 mm (0.98 in.)

    NOTICE:
    Make sure that there is no oil on the bolt and nut threads.

  1. Fully tighten the bolts in this order: Area 1 and Area 2.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

  1. Fully tighten the bolts in Area 3.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

    HINT:
    First tighten the upper bolts and nuts followed by lower bolts and nuts as shown in the illustration.

  1. Fully tighten the bolts in Area 4.

    Torque:
    43 N*m{ 438 kgf*cm , 32 ft.*lbf } for bolt A
    21 N*m{ 214 kgf*cm , 15 ft.*lbf } for bolts except bolt A

    HINT:
    Tighten the bolts in the order of lower to upper as shown in the illustration.

  1. Install a new chain cover plate gasket and the chain cover plate with the 4 bolts.

    Torque:
    9.1 N*m{ 93 kgf*cm , 81 in.*lbf }


26. INSTALL WATER INLET HOUSING

  1. A129675E01
    Install 2 new O-rings.

    HINT:
    Apply a small amount of water or soapy water to O-ring (A) in the illustration before installation.

  1. A137975E01
    Install the 2 stud bolts.

    Torque:
    4.0 N*m{ 41 kgf*cm , 35 in.*lbf }

  1. A134879E01
    Install the water inlet housing with the 2 bolts and nut.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

    NOTICE:
    Be careful that the O-ring does not get caught between the parts.

  1. Connect the No. 1 water by-pass hose.

  1. Apply adhesive around the drain cock.

    Adhesive:
    Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent

  1. Install the drain cock assembly to the water inlet housing.

    Torque:
    30 N*m{ 306 kgf*cm , 22 ft.*lbf }

  1. Install the drain cock plug to the drain cock assembly.

    Torque:
    13 N*m{ 130 kgf*cm , 9 ft.*lbf }

  1. Install a new gasket to the thermostat.

  1. A134896E01
    Align the thermostat jiggle valve with the upper stud bolt, and insert the thermostat in the water inlet housing.

    HINT:
    The jiggle valve may be set within 10° of either side of the prescribed position.

  1. A129673
    Install the water inlet with the 2 nuts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }


27. INSTALL NO. 1 FRONT ENGINE MOUNTING BRACKET LH

  1. A134961E01
    Install the No. 1 front engine mounting bracket LH with the 6 bolts.

    Torque:
    54 N*m{ 551 kgf*cm , 40 ft.*lbf }

    NOTICE:
    1. Install the water inlet and mounting bracket within 15 minutes after installing the chain cover.
    2. Do not start the engine for at least 2 hours after installation.

  1. When replacing a stud bolt, install it by using an E8 "TORX" socket wrench.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }


28. INSTALL OIL PAN BAFFLE PLATE NO.1

  1. A129685E01
    Install the oil pan baffle plate with the 7 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

    HINT:
    Temporarily tighten the 7 bolts. Fully tighten 2 bolts (A) as shown in the illustration before tightening the other bolts.


29. INSTALL OIL PAN SUB-ASSEMBLY

  1. When replacing a stud bolt, install it by using an E8 "TORX" socket wrench. installaction

    A136298E01

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

  1. A129684
    Install 2 new O-rings.

  1. A132232E05
    Apply seal packing in a continuous line as shown in the illustration.

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    Seal diameter:
    3.0 to 4.0 mm (0.118 to 0.156 in.)

    NOTICE:
    1. Remove any oil from the contact surface.
    2. Install the oil pan within 3 minutes after applying seal packing.
    3. Do not start the engine for at least 2 hours after installing.

  1. A242991E01
    Install the oil pan with the 16 bolts and 2 nuts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf } for bolt A
    21 N*m{ 214 kgf*cm , 15 ft.*lbf } for bolts except A


30. INSTALL OIL STRAINER SUB-ASSEMBLY

  1. A134963E01
    Using an E6 "TORX" socket, install the stud bolts as shown in the illustration.

    Torque:
    4.0 N*m{ 41 kgf*cm , 35 in.*lbf }

  1. A129681E01
    Install a new gasket and the oil strainer sub-assembly with the bolt and 2 nuts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }


31. INSTALL NO. 2 OIL PAN SUB-ASSEMBLY

  1. A134964E01
    Using an E6 "TORX" socket, install the stud bolts as shown in the illustration.

    Torque:
    4.0 N*m{ 41 kgf*cm , 35 in.*lbf }

  1. A132234E04
    Apply seal packing in a continuous line as shown in the illustration.

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    Seal diameter:
    3.0 to 4.0 mm (0.118 to 0.158 in.)

    NOTICE:
    1. Remove any oil from the contact surface.
    2. Install the No. 2 oil pan sub-assembly within 3 minutes after applying seal packing.
    3. Do not start the engine for at least 2 hours after installing.

  1. A129680E01
    Install the No. 2 oil pan sub-assembly with the 16 bolts and 2 nuts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }


32. INSTALL OIL PAN DRAIN PLUG

  1. A129654
    Install a new oil pan drain plug gasket and the oil pan drain plug.

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }


33. INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY (for Bank 1)

  1. A132236E01
    Apply seal packing as shown in the illustration.

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    NOTICE:
    1. Remove any oil from the contact surface.
    2. Install the head cover within 3 minutes after applying seal packing.
    3. Do not start the engine for at least 2 hours after installing.

  1. A129699
    Install 3 new gaskets as shown in the illustration.

  1. Install a new gasket to the head cover.

  1. A129679E01
    Install a head cover with the 12 bolts and a new seal washer.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf } for bolt A
    10 N*m{ 102 kgf*cm , 7 ft.*lbf } for bolts except A

    HINT:
    After tightening all bolts, check the tightening torque of 1 and 11. Retighten the bolt if necessary.


34. INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY (for Bank 2)

  1. A132237E01
    Apply seal packing as shown in the illustration.

    Seal packing:
    Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

    NOTICE:
    1. Remove any oil from the contact surfaces.
    2. Install the cylinder head cover sub-assembly within 3 minutes after applying seal packing.
    3. Do not start the engine for at least 2 hours after installing.

  1. A129705
    Install 3 new gaskets as shown in the illustration.

  1. Install a new cylinder head cover gasket to the cylinder head cover sub-assembly.

  1. A129678E03
    Install the cylinder head cover sub-assembly with the 12 bolts and a new seal washer.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf } for bolt A
    10 N*m{ 102 kgf*cm , 7 ft.*lbf } for bolts except A

    HINT:
    After tightening all bolts, check the tightening torque of 1 and 10. Retighten the bolt if necessary.


35. INSTALL WATER OUTLET

  1. A129677
    Install 2 new gaskets and a new O-ring.

    HINT:
    Apply soapy water to the O-ring.

  1. A129676E01
    Install the water outlet with the 2 bolts and 4 nuts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf } for bolts
    10 N*m{ 102 kgf*cm , 7 ft.*lbf } for nuts

    NOTICE:
    Be careful that the O-ring does not get caught between the parts.


36. INSTALL NO. 1 ENGINE OIL LEVEL DIPSTICK GUIDE

  1. A171897
    Apply a light coat of engine oil to a new O-ring and install it to the No. 1 engine oil level dipstick guide.

  1. A171870
    Install the bolt and No. 2 dipstick guide.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }


37. INSTALL NO. 1 OIL COOLER BRACKET

  1. A139009E01
    Using an E8 "TORX" socket, install the 2 stud bolts as shown in the illustration.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

  1. A136294E01
    Install a new gasket to the No. 1 oil cooler bracket.

  1. Install the oil cooler pipe with the bolt and 2 nuts.

    Torque:
    21 N*m{ 214 kgf*cm , 16 ft.*lbf }

  1. A136293
    Install a new gasket to the No. 1 oil pan.

  1. Install the No. 1 oil cooler bracket with oil cooler pipe with the 3 bolts and 3 nuts.

    Torque:
    21 N*m{ 214 kgf*cm , 16 ft.*lbf }


38. INSTALL OIL COOLER ASSEMBLY

  1. A136292
    Install a new O-ring.

  1. Install the oil cooler assembly with the union bolt.

    Torque:
    68 N*m{ 693 kgf*cm , 50 ft.*lbf }

  1. A136291
    Install the 2 water by-pass hoses with the bolt, 2 clamps, and 4 clips.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }


39. INSTALL CRANKSHAFT PULLEY
  1. Align the pulley set key with the key groove of the pulley, and slide on the pulley.

  1. A122396E01
    Using SST, install the pulley bolt.
    SST
    09213-70011   (09213-70020)
    09330-00021  

    Torque:
    250 N*m{ 2550 kgf*cm , 184 ft.*lbf }


40. INSTALL OIL FILTER ELEMENT

  1. A106167E01
    Clean the inside of the oil filter cap sub-assembly, the threads and O-ring groove.

  1. Apply a light coat of engine oil to a new O-ring and install it to the oil filter cap sub-assembly.

  1. Set a new oil filter element to the oil filter cap sub-assembly.

  1. Remove dirt and foreign matter from the installation surface of the engine.

  1. Apply a light coat of engine oil to the O-ring again and install the oil filter cap sub-assembly.

    NOTICE:
    1. Be careful that the O-ring does not get caught between any parts.
    2. The O-ring must not be twisted on the groove.

  1. A132239E01
    Using SST, tighten the oil filter cap sub-assembly.
    SST
    09228-06501  

    Torque:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf }

    NOTICE:
    Make sure that the oil filter is installed securely as shown in the illustration.

  1. A128003E02
    Apply a light coat of engine oil to a new O-ring and install it to the oil filter cap.

    NOTICE:
    Remove all dirt and foreign matter from the installation surfaces.

  1. Install the oil filter drain plug to the oil filter cap sub-assembly.

    Torque:
    13 N*m{ 127 kgf*cm , 9 ft.*lbf }

    NOTICE:
    Make sure that the O-ring does not get caught between the parts.


41. INSTALL CYLINDER BLOCK WATER DRAIN COCK SUB-ASSEMBLY

  1. A076531E01
    Apply adhesive around the drain cock sub-assembly.

    Adhesive:
    Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent

  1. A135830E03
    Install the water drain cocks as shown in the illustration.

    Torque:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf }

    NOTICE:
    Do not rotate the drain cocks more than 1 revolution (360°) after tightening the drain cocks with the specified torque.

  1. Install the water drain cock plugs to the water drain cocks.

    Torque:
    13 N*m{ 130 kgf*cm , 9 ft.*lbf }


42. INSTALL NO. 1 OIL PIPE
  1. Make sure that there is no foreign matter on the mesh of the oil control valve filter LH.

    NOTICE:
    Do not touch the mesh when installing the oil control valve filter.

  1. A135726E01
    Install the oil control valve filter LH to the oil pipe union. Install new gaskets and temporarily install the oil pipe (on the head cover side).

  1. Install a new gasket and temporarily install the oil pipe (on the cylinder head side) with the oil check valve bolt.

  1. Tighten the oil pipe union (on the head cover side).

    Torque:
    65 N*m{ 663 kgf*cm , 48 ft.*lbf }

  1. Tighten the oil pipe union (on the cylinder head side).

    Torque:
    65 N*m{ 663 kgf*cm , 48 ft.*lbf }

    NOTICE:
    If the link that connects the gaskets is broken, remove the connecting link by using side cutters or a similar tool.


43. INSTALL OIL PIPE
  1. Make sure that there is no foreign matter on the mesh of the oil control valve filter RH.

    NOTICE:
    Do not touch the mesh when installing the oil control valve filter.

  1. A134878E02
    Install the oil control valve filter RH to the oil pipe union. Install new gaskets and temporarily install the oil pipe (on the head cover side).

  1. Install a new gasket and temporarily install the oil pipe (on the cylinder head side) with the oil check valve bolt.

  1. Install the bolt (A) to the cylinder head.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

  1. Tighten the oil pipe union (on the head cover side).

    Torque:
    65 N*m{ 663 kgf*cm , 48 ft.*lbf }

  1. Tighten the oil pipe union (on the cylinder head side).

    Torque:
    65 N*m{ 663 kgf*cm , 48 ft.*lbf }

    NOTICE:
    If the link that connects the gaskets is broken, remove the connecting link by using side cutters or a similar tool.


44. INSTALL CRANKSHAFT POSITION SENSOR

  1. A129663
    Install the crankshaft position sensor with the bolt.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }


45. INSTALL CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY

  1. A129662E07
    Install the 4 camshaft timing oil control valves with the 4 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }


46. INSTALL CAMSHAFT POSITION SENSOR

  1. A129656E04
    Install the 4 camshaft position sensors with the 4 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }


47. INSTALL VENTILATION VALVE SUB-ASSEMBLY
  1. Apply adhesive around the ventilation valve sub-assembly.

    Adhesive:
    Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent

  1. A129655
    Install the ventilation valve sub-assembly.

    Torque:
    27 N*m{ 275 kgf*cm , 20 ft.*lbf }


48. INSTALL SPARK PLUG
  1. Install the 6 spark plugs.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }


49. INSTALL OIL FILLER CAP SUB-ASSEMBLY
  1. Install a new oil filler gasket.

  1. Install the oil filler cap sub-assembly.

← REASSEMBLY (May 2007 – Jun 2010)REASSEMBLY (Jul 2012 – Jul 2013) →