2007-2013 Highlander Kluger · Service Manual BODY ELECTRICAL

TERMINALS OF ECU

System information · Vehicles built from May 2007


CHECK MAIN BODY ECU (INSTRUMENT PANEL JUNCTION BLOCK)
  1. Disconnect the D6, D7 and D9 main body ECU connectors.

  2. Disconnect the 1O, 1K, 1M, 1D, 1F and 1J instrument panel junction block connectors.
    B112605E15

  3. Measure the voltage and resistance according to the value(s) in the table below.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    D7-24 (DCTY) - Body ground
    G - Body ground (*1)
    SB - Body ground (*2)
    Driver door courtesy switch
    Driver door CLOSED → OPEN
    10 kΩ or higher →
    Below 1 Ω
    D6-7 (RCTY) - Body ground
    GR - Body ground
    Rear right door courtesy switch input
    Rear right door CLOSED → OPEN
    10 kΩ or higher →
    Below 1 Ω
    D6-21 (PCTY) - Body ground
    SB - Body ground (*1)
    G - Body ground (*2)
    Front passenger door courtesy switch input
    Front passenger door CLOSED → OPEN
    10 kΩ or higher →
    Below 1 Ω
    1O-7 (LCTY) - Body ground
    B - Body ground
    Rear left door courtesy switch input
    Rear left door CLOSED → OPEN
    10 kΩ or higher →
    Below 1 Ω
    1M-9 (GND2) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    1F-10 (GND1) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    1J-3 (L1) - Body ground
    L - Body ground (*1)
    R - Body ground (*2)
    Front passenger door control switch LOCK input
    Front passenger door control switch OFF → LOCK
    10 kΩ or higher →
    Below 1 Ω
    1J-4 (UL1) - Body ground
    G - Body ground
    Front passenger door control switch UNLOCK input
    Front passenger door control switch OFF → UNLOCK
    10 kΩ or higher →
    Below 1 Ω
    1K-15 (L1) - Body ground
    O - Body ground (*1)
    LG - Body ground (*2)
    Driver door control switch LOCK input
    Driver door control switch OFF → LOCK
    10 kΩ or higher →
    Below 1 Ω
    1K-12 (UL1) - Body ground
    G - Body ground
    Driver door control switch UNLOCK input
    Driver door control switch OFF → UNLOCK
    10 kΩ or higher →
    Below 1 Ω
    D9-5 (KSW) - Body ground (*3)
    GR - Body ground
    Unlock warning switch signal input
    No key is in ignition key cylinder → Key is in ignition key cylinder
    10 kΩ or higher →
    Below 1 Ω
    D6-25 (BCTY) - Body ground
    L - Body ground
    Back door courtesy switch input
    Back door CLOSED → OPEN
    10 kΩ or higher →
    Below 1 Ω
    1D-10 (BECU) - Body ground (*3)
    W - Body ground
    +B (BECU) power supply
    Always
    11 to 14 V

    HINT:
    1. *1: for LHD
    2. *2: for RHD
    3. *3: w/o Smart Entry and Start System

    If the result is not as specified, there may be a malfunction on the wire harness side.

  4. Reconnect the D6, D7 and D9 main body ECU connectors.

  5. Reconnect the 1O, 1K, 1M, 1D, 1F and 1J instrument panel junction block connectors.

  6. Measure the voltage according to the value(s) in the table below.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    1F-11 (IG) - Body ground
    P - Body ground
    Engine power supply
    Ignition switch on (IG) → off
    11 to 14 V →
    Below 1 V
    1F-2 (ACC) - Body ground
    SB - Body ground
    ACC power supply
    Ignition switch on (ACC) → off
    11 to 14 V →
    Below 1 V
    IP-5 (LSWL) - Body ground
    G - Body ground
    Rear left door lock position switch input
    Rear left door UNLOCK → LOCK
    Below 1 V →
    11 to 14 V (or pulse generation)
    D7-9 (LSWD) - Body ground
    GR - Body ground
    Driver door lock position switch input
    Driver door UNLOCK → LOCK
    Below 1 V →
    11 to 14 V (or pulse generation)
    D7-10 (UL3) - Body ground (*2)
    V - Body ground
    Driver door key-linked door unlock input
    Driver door lock cylinder is turned LOCK → UNLOCK with mechanical key
    Below 1 V →
    11 to 14 V (or pulse generation)
    1K-16 (L2) - Body ground
    BR - Body ground
    Driver door key-linked door lock input
    Driver door lock cylinder is turned UNLOCK → LOCK with mechanical key
    Below 1 V →
    11 to 14 V (or pulse generation)
    1J-1 (ACT+) - Body ground
    P - Body ground
    Door lock motor LOCK drive output (Front passenger door)
    Door control switch (Master switch or front passenger side switch) or driver side door key cylinder OFF → LOCK → OFF
    Below 1 V →
    11 to 14 V →
    Below 1 V
    IP-11 (ACT+) - Body ground
    GR - Body ground
    Door lock motor LOCK drive output (Rear door LH)
    Door control switch (Master switch or front passenger side switch) or driver side door key cylinder OFF → LOCK → OFF
    Below 1 V →
    11 to 14 V →
    Below 1 V
    1F-5 (ACT+) - Body ground
    W - Body ground
    Door lock motor LOCK drive output (Rear door RH)
    Door control switch (Master switch or front passenger side switch) or driver side door key cylinder OFF → LOCK → OFF
    Below 1 V →
    11 to 14 V →
    Below 1 V
    IP-6 (ACT-) - Body ground
    W - Body ground
    Door lock motor UNLOCK drive output (Rear door LH)
    Door control switch (Master switch or front passenger side switch) or driver side door key cylinder OFF → UNLOCK → OFF
    Below 1 V →
    11 to 14 V →
    Below 1 V
    1F-18 (ACT-) - Body ground
    G - Body ground
    Door lock motor UNLOCK drive output (Rear door RH)
    Door control switch (Master switch or front passenger side switch) or driver side door key cylinder OFF → UNLOCK → OFF
    Below 1 V →
    11 to 14 V →
    Below 1 V
    D7-1 (TR+) - Body ground (*3)
    LG - Body ground
    Door lock motor UNLOCK drive output (Back door)
    Back door opener switch (Transmitter) OFF → UNLOCK → OFF
    Below 1 V →
    11 to 14 V →
    Below 1 V
    D7-5 (ACTD) - Body ground (*2)
    W - Body ground (*1)
    R - Body ground (*2)
    Door lock motor UNLOCK drive output (Driver door)
    Door control switch (Master switch or front passenger side switch) or driver side door key cylinder OFF → UNLOCK → OFF
    Below 1 V →
    11 to 14 V →
    Below 1 V
    1K-2 (ACT+) - Body ground
    R - Body ground
    Door lock motor LOCK drive output (Front LH side)
    Door control switch (Master switch or front passenger side switch) or driver side door key cylinder OFF → LOCK → OFF
    Below 1 V →
    11 to 14 V →
    Below 1 V
    1J-2 (ACT-) - Body ground
    LG - Body ground (*1)
    W - Body ground (*2)
    Door lock motor UNLOCK drive output (Front passenger door)
    Door control switch (Master switch or front passenger side switch) or driver side door key cylinder OFF → UNLOCK → OFF
    Below 1 V →
    11 to 14 V →
    Below 1 V
    D6-5 (LSWR) - Body ground
    B - Body ground
    Rear right door lock position switch input
    Rear right door UNLOCK → LOCK
    Below 1 V →
    11 to 14 V (or pulse generation)
    D6-27 (LSWP) - Body ground
    SB - Body ground (*1)
    W - Body ground (*2)
    Front passenger door lock position switch input
    Front passenger door UNLOCK → LOCK
    Below 1 V →
    11 to 14 V (or pulse generation)

    HINT:
    1. *1: for LHD
    2. *2: for RHD
    3. *3: w/o Power Back Door

    If the result is not as specified, the main body ECU (instrument panel junction block) may have a malfunction.

← PROBLEM SYMPTOMS TABLE (from Jul 2010)DIAGNOSIS SYSTEM (from May 2007) →