2007-2013 Highlander Kluger · Service Manual SECURITIES

B278A Short to GND in Immobiliser System Power Source Circuit

Diagnostic trouble codes · Vehicles built from Jul 2010

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010

DESCRIPTION

This DTC is output when the engine switch power source supply line is open or shorted.
DTC No.
DTC Detection Condition
Trouble Area
B278A
Engine switch power source supply line is open or shorted
  1. Wire harness or connector
  2. Engine switch
  3. Certification ECU (Smart key ECU assembly)

WIRING DIAGRAM

B151005E04

INSPECTION PROCEDURE

NOTICE:
If the certification ECU (smart key ECU assembly) is replaced, register the key and ECU communication ID.


1. CHECK DTC OUTPUT
  1. Delete the DTCs (Click here).

  1. Recheck for DTCs.

    OK:
    B278A output does not recur.



NG
Go to step 2
OK

USE SIMULATION METHOD TO CHECK (Click here)

2. CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - ENGINE SWITCH)

  1. B178824E02
    Disconnect the certification ECU (smart key ECU assembly) and engine switch connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    D36-30 (VC5) - D22-14 (VC5)
    Always
    Below 1 Ω
    D36-40 (AGND) - D22-8 (AGND)
    Always
    Below 1 Ω
    D36-17 (E) - Body ground
    Always
    Below 1 Ω
    D36-30 (VC5) - Body ground
    Always
    10 kΩ or higher
    D36-40 (AGND) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. CHECK HARNESS AND CONNECTOR (ENGINE SWITCH POWER SOURCE)

  1. B178823E01
    Reconnect the certification ECU (smart key ECU assembly) and engine switch connectors.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    D36-30 (VC5) - Body ground
    Engine switch off, brake pedal not depressed, 30 seconds or more elapsed after driver door opened and then closed
    Below 1 V

  1. B216007E01
    Using an oscilloscope, check the waveform.
    Measurement condition 
    Tester Connection
    Condition
    Tool Setting
    Specified Condition
    D36-30 (VC5) - Body ground
    Engine switch off, key not in cabin, within 30 seconds after engine switch pressed
    2 V/DIV., 200 ms./DIV.
    Pulse generation

    OK:
    The waveform is similar to that shown in the illustration.



NG
REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
OK


4. CHECK HARNESS AND CONNECTOR (ENGINE SWITCH BODY GROUND)

  1. B178823E02
    Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    D36-40 (AGND) - Body ground
    Always
    Below 1 Ω



NG
REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
OK

REPLACE ENGINE SWITCH (Click here)


← B278A Short to GND in Immobiliser System Power Source Circuit (Aug 2008 – Jun 2010)B2790 ID BOX EEPROM Malfunction (from May 2007) →