2007-2013 Highlander Kluger · Service Manual ENGINE

INSTALLATION

Removal / installation · Vehicles built from Jul 2010

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010


1. INSTALL V-RIBBED BELT

  1. A162386E01
    Install the V-ribbed belt.

  1. Using SST, turn the V-ribbed belt tensioner assembly counterclockwise and remove the bar.

    SST
    09961-00950  

  1. A139509E01
    If it is difficult to install the V-ribbed belt, perform the following procedure:

    1. Put the V-ribbed belt on every pulley except the tensioner pulley as shown in the illustration.

    2. Release the V-ribbed belt tension by turning the V-ribbed belt tensioner assembly counterclockwise, and put the V-ribbed belt on the V-ribbed belt tensioner assembly pulley.

      NOTICE:
      1. Put the backside of the V-ribbed belt on the V-ribbed belt tensioner assembly pulley and No. 2 idler pulley sub-assembly.
      2. Check that the V-ribbed belt is properly set to each pulley.

    3. After installing the V-ribbed belt, check that it fits properly in the ribbed grooves. Confirm that the V-ribbed belt has not slipped out of the grooves on the bottom of the crankshaft pulley by hand.


2. INSTALL FRONT FENDER APRON SEAL RH

  1. A171853
    Install the front fender apron seal RH with the 2 bolts and clip.


3. INSTALL FRONT FENDER LINER RH

  1. B260028
    Install the front fender liner RH with the 5 clips and 8 screws.

  1. Install the bolt.

  1. B260030
    Install 3 new grommets.

  1. Using a 4 mm hexagon wrench, install the 2 screws.

  1. B261128E01
    Install the screw and 2 pin hold clips.
    Text in Illustration 
    *1
    Correct
    *2
    Incorrect

    NOTICE:
    Insert the pin hold clip with the slot aligned vertically. Do not rotate the clip after inserting it. After installation, confirm that the slot is aligned vertically.


4. INSTALL FRONT FENDER MOULDING SUB-ASSEMBLY RH
  1. Clean the vehicle body surface.

    1. Using a heat light, heat the vehicle body surface.

    2. Remove the front fender side protector from the vehicle body.

    3. Wipe off any tape adhesive residue with cleaner.

  1. A176045
    Clean the front fender moulding sub-assembly RH. (If reusing the front fender moulding sub-assembly RH)

    1. Using a heat light, heat the front fender moulding sub-assembly RH.

    2. Remove the front fender side protector from the front fender moulding sub-assembly RH.

    3. Wipe off any tape adhesive residue with cleaner.

    4. Install a new front fender side protector to the the front fender moulding sub-assembly RH.

  1. A176044
    Install the front fender moulding sub-assembly RH.

    1. Using a heat light, heat the vehicle body and the front fender moulding sub-assembly RH.

    2. Remove the release paper from the front fender moulding sub-assembly RH.

      HINT:
      After removing the release paper, keep the exposed adhesive free from foreign matter.

    3. Engage the 3 clips and install the front fender moulding sub-assembly RH.

  1. A176043
    Using a 4 mm hexagon wrench, install the screw.

  1. Install the clip.


5. INSTALL NO. 1 ENGINE UNDER COVER

  1. A237657
    Install the No. 1 engine under cover with the 6 bolts and 2 clips.


6. INSTALL ENGINE UNDER COVER ASSEMBLY

  1. A171850
    Install the engine under cover assembly with the 2 bolts, 2 screws and 5 clips.

  1. A171849
    Install the engine under cover assembly RR with the 2 bolts.


7. INSTALL FRONT WHEEL RH

Torque:
103 N*m{ 1050 kgf*cm , 76 ft.*lbf }

← INSTALLATION (Aug 2008 – Jun 2010)COMPONENTS (May 2007 – Jun 2010) →