2007-2013 Highlander Kluger · Service Manual BRAKE

ADJUSTMENT

Removal / installation · Vehicles built Aug 2008 – Jun 2010

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010


1. INSPECT PARKING BRAKE PEDAL TRAVEL
  1. Fully depress the parking brake pedal and release it to engage the parking brake.

  1. Depress the pedal to the floor again, and release it to disengage the parking brake.

  1. C107204
    Slowly depress the parking brake pedal to the floor, and count the number of clicks.

    Parking brake pedal travel:
    8 to 10 notches at 300 N (31 kgf, 67 lbf)

    If the parking brake pedal travel is not as specified, adjust the parking brake shoe clearance and parking brake pedal travel.


2. ADJUST PARKING BRAKE SHOE CLEARANCE AND PARKING BRAKE PEDAL TRAVEL (for LHD)
  1. Remove the driver side knee airbag assembly (Click here).

  1. Completely release the parking brake pedal.

  1. C166160E01
    Loosen the lock nut and the adjusting nut to completely release the parking brake cable.

  1. Remove the rear wheel.

  1. Temporarily install the hub nuts.

  1. Remove the shoe adjusting hole plug.

  1. C131914E01
    Turn the shoe adjuster and expand the shoe until the disc locks.

  1. Turn and contract the shoe adjuster until the disc can rotate smoothly.

    Standard:
    Return 8 notches.

  1. Check that there is no brake drag against the shoe.

  1. Install the shoe adjusting hole plug.

  1. Turn the adjusting nut until the parking brake pedal travel is corrected to be within the specified range.

    Parking brake pedal travel:
    8 to 10 notches at 300 N (31 kgf, 67 lbf)

  1. Using a wrench or an equivalent tool, hold the adjusting nut and tighten the lock nut.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }

  1. Operate the parking brake pedal 3 to 4 times, and check the parking brake pedal travel.

  1. Check that there is no brake drag against the shoe.

  1. Remove the hub nuts.

  1. Install the rear wheel.

    Torque:
    103 N*m{ 1050 kgf*cm , 76 ft.*lbf }

  1. Install the driver side knee airbag assembly (Click here).


3. ADJUST PARKING BRAKE SHOE CLEARANCE AND PARKING BRAKE PEDAL TRAVEL (for RHD)
  1. Remove the driver side knee airbag assembly (Click here).

  1. Completely release the parking brake pedal.

  1. C165692E01
    Loosen the lock nut and adjusting nut to completely release the parking brake cable.

  1. Remove the rear wheel.

  1. Temporarily install the hub nuts.

  1. Remove the shoe adjusting hole plug.

  1. C131914E01
    Turn the shoe adjuster and expand the shoe until the disc locks.

  1. Turn and contract the shoe adjuster until the disc can rotate smoothly.

    Standard:
    Return 8 notches.

  1. Check that there is no brake drag against the shoe.

  1. Install the shoe adjusting hole plug.

  1. Turn the adjusting nut until the parking brake pedal travel is corrected to be within the specified range.

    Parking brake pedal travel:
    8 to 10 notches at 300 N (31 kgf, 67 lbf)

  1. Using a wrench or an equivalent tool, hold the adjusting nut and tighten the lock nut.

    Torque:
    7.0 N*m{ 71 kgf*cm , 62 in.*lbf }

  1. Operate the parking brake pedal 3 to 4 times, and check the parking brake pedal travel.

  1. Check that there is no brake drag against the shoe.

  1. Remove the hub nuts.

  1. Install the rear wheel.

    Torque:
    103 N*m{ 1050 kgf*cm , 76 ft.*lbf }

  1. Install the driver side knee airbag assembly (Click here).


4. INSPECT BRAKE WARNING LIGHT
  1. When operating the parking brake pedal, check that the brake warning light illuminates.

    Standard:
    The brake warning light always illuminates at the first click.

← ADJUSTMENT (May 2007 – Jul 2008)ADJUSTMENT (from Jul 2010) →