2007-2013 Highlander Kluger · Service Manual RESTRAINTS

DISPOSAL

Removal / installation · Vehicles built from Jul 2010

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010

HINT:
When scrapping a vehicle equipped with an SRS or disposing of the steering pad, be sure to deploy the airbag first in accordance with the procedure described below. If any abnormality occurs with the airbag deployment, contact the Service Dept. of the distributor.

CAUTION:
  1. An airbag or pretensioner may be activated by static electricity. To prevent this, be sure to touch a metal surface with your bare hands to discharge static electricity before performing this procedure.
  2. Never dispose of a steering pad with an undeployed airbag.
  3. The airbag produces an exploding sound when it is deployed, so perform the operation outdoors and where it will not create a nuisance to nearby residents.
  4. When deploying the airbag, always use the specified SST (SRS Airbag Deployment Tool). Perform the operation in a place away from electrical noise.
  5. When deploying the airbag, perform the operation at least 10 m (33 ft.) away from the steering pad.
  6. The steering pad becomes extremely hot when the airbag is deployed, so do not touch it for at least 30 minutes after deployment.
  7. Use gloves and safety glasses when handling a steering pad with a deployed airbag.
  8. Do not apply water, etc. to a steering pad with a deployed airbag.
  9. Always wash your hands with water after completing the operation.


1. DISPOSE OF STEERING PAD (WHEN INSTALLED IN VEHICLE)

HINT:
Prepare a battery as the power source to deploy the airbag.

  1. C110371E06
    Check the function of SST.
    SST
    09082-00700  

    CAUTION:
    When deploying the airbag, always use the specified SST:
    SRS Airbag Deployment Tool


    1. C110372E05
      Connect SST to the battery.
      Connect the red clip of SST to the battery positive (+) terminal and the black clip of SST to the negative (-) terminal.

    2. C110475E01
      Check the function of SST.
      Press the SST activation switch and check that the LED of the SST activation switch comes on.

      CAUTION:
      1. Do not connect the SST connector (yellow colored one) to the airbag.
      2. If the LED comes on when the activation switch is not being pressed, an SST malfunction is possible, so replace SST with a new one.

    3. Disconnect SST from the battery.

  1. Refer to PRECAUTION (Click here).

  1. Disconnect the cable from the negative battery terminal.

    CAUTION:
    Wait for at least 90 seconds after disconnecting the cable to prevent airbag deployment.

  1. C166984
    Remove the steering column cover (lower).

    1. While turning the steering wheel assembly to the right and left, remove the 2 screws and steering column cover (lower).

  1. Install SST.

    CAUTION:
    Check that there is no looseness in the steering wheel assembly and steering pad.


    1. Disconnect the airbag connector (yellow colored one) from the spiral cable.

      NOTICE:
      When handling the airbag connector, take care not to damage the airbag wire harness.

    2. C166983E01
      Connect the SST connector to the airbag connector of the spiral cable.
      SST
      09082-00700  
      09082-00780  

      NOTICE:
      To avoid damaging the SST connector and wire harness, do not lock the secondary lock of the twin lock.

    3. C110476E12
      Move SST at least 10 m (33 ft.) away from the vehicle front side window.

    4. Maintaining sufficient clearance for the SST wire harness in the front side window, close all doors and windows of the vehicle.

      NOTICE:
      Take care not to damage the SST wire harness.

    5. Connect the red clip of SST to the battery positive (+) terminal and the black clip of SST to the negative (-) terminal.

  1. Deploy the airbag.

    1. Check that no one is inside the vehicle or within a 10 m (33 ft.) radius of the vehicle.

    2. Press the SST activation switch and deploy the airbag.

      CAUTION:
      1. When deploying the airbag, make sure that no one is near the vehicle.
      2. The steering pad becomes extremely hot when the airbag is deployed, so do not touch it for at least 30 minutes after deployment.
      3. Use gloves and safety glasses when handling a steering pad with a deployed airbag.
      4. Do not apply water, etc. to a steering pad with a deployed airbag.
      5. Always wash your hands with water after completing the operation.

      HINT:
      The airbag is deployed as the LED of the SST activation switch comes on.


2. DISPOSE OF STEERING PAD (WHEN NOT INSTALLED IN VEHICLE)

NOTICE:
  1. When disposing of the steering pad, never use the customer's vehicle to deploy the airbag.
  2. Be sure to follow the procedure detailed below when deploying the airbag.

HINT:
Prepare a battery as the power source to deploy the airbag.

  1. C110371E06
    Check the function of SST.
    SST
    09082-00700  

    CAUTION:
    When deploying the airbag, always use the specified SST:
    SRS Airbag Deployment Tool


    1. C110372E05
      Connect SST to the battery.
      Connect the red clip of SST to the battery positive (+) terminal and the black clip of SST to the negative (-) terminal.

    2. C110475E01
      Check the function of SST.
      Press the SST activation switch and check that the LED of the SST activation switch comes on.

      CAUTION:
      1. Do not connect the SST connector (yellow colored one) to the airbag.
      2. If the LED comes on when the activation switch is not being pressed, an SST malfunction is possible, so replace SST with a new one.

    3. Disconnect SST from the battery.

  1. Remove the steering pad (Click here).

    CAUTION:
    1. When removing the steering pad, work must be started at least 90 seconds after the ignition switch is turned off and the negative (-) terminal cable is disconnected from the battery.
    2. When storing the steering pad, keep the airbag deployment side facing upward.

  1. B104882E16
    Using braided wire, tie down the steering pad to an unneeded wheel.

    Wire:
    Stripped wire section
    1.25 mm2 (0.0019 in.2) or more

    CAUTION:
    If the wire is too thin or an alternative object is used to tie down the steering pad, it may be snapped by the shock when the airbag is deployed. Always use a wire for vehicle use with an area of at least 1.25 mm2 (0.0019 in.2).

    HINT:
    To calculate the area of the stripped wire section:
    Area = 3.14 x (Diameter)2 divided by 4


    1. C138936E01
      Install the 2 bolts with washers into the 2 bolt holes on the steering pad.

      Bolt:
      L:
      35.0 mm (1.378 in.)
      M:
      6.0 mm (0.236 in.)
      Pitch:
      1.0 mm (0.039 in.)

      NOTICE:
      1. Tighten the bolts by hand until they become difficult to turn.
      2. Do not tighten the bolts excessively.

    2. C138937E01
      After connecting the following SST to each other, connect them to the steering pad.
      SST
      09082-00802   (09082-10801, 09082-30801)

    3. C138938E01
      Wind 3 wires at least 2 times each around each of the bolts installed on the left and right sides of the steering pad.

      CAUTION:
      1. Tightly wind the wires around the bolts so that there is no slack.
      2. Make sure that the wires are tight. If there is slack in the wires, the steering pad may break loose due to the shock when the airbag is deployed.

    4. C138939
      Face the airbag deployment side of the steering pad upward on top of an unneeded tire and wheel set. Separately tie the left and right sides of the steering pad to the wheel through the hub nut holes. Position the SST connector so that it hangs downward through the hub hole of the wheel.

      CAUTION:
      1. Make sure that the wires are tight. If there is slack in the wires, the steering pad may break loose due to the shock when the airbag is deployed.
      2. Always tie down the steering pad with the airbag deployment side facing upward.

      NOTICE:
      The wheel will be damaged by the airbag deployment, so use an unneeded wheel.

  1. C138940E01
    Install SST.

    CAUTION:
    Place the wheel on level ground.


    1. Connect the SST connector.

      SST
      09082-00700  

      NOTICE:
      To avoid damaging the SST connector and wire harness, do not lock the secondary lock of the twin lock. Also, secure some slack for the SST wire harness inside the wheel.

    2. C111070E04
      Move SST at least 10 m (33 ft.) away from the airbag tied down to the wheel.

  1. C111071E04
    Cover the steering pad (using a cardboard box).

    1. Cover the steering pad with the cardboard box.

    2. Place weights on the cardboard box in 4 places totalling at least 190 N (19 kg, 43 lb).

      Minimum cardboard box size:
      Must exceed the following dimensions
      X:
      460 mm (18.11 in.)
      Y:
      650 mm (25.59 in.)

      NOTICE:
      1. When dimension Y of the cardboard box exceeds the diameter of the wheel and tire which the steering pad is tied to, X should be the following size.
        X = 460 mm (18.11 in.) + width of tire
      2. If a cardboard box which is smaller than the specified size is used, the cardboard box may be broken by the shock from the airbag deployment.

  1. Cover the steering pad (using tires).

    1. C111105E05
      Place at least 3 tires without wheels onto the wheel and tire which the steering pad is tied to.

    2. Place the wheel and tire on top of them.

      Minimum tire size:
      Must exceed the following dimensions

      Width:
      185 mm (7.28 in.)

      Inner diameter:
      360 mm (14.17 in.)

      CAUTION:
      Do not use tires with wheels except for on the top and bottom.

      NOTICE:
      1. The tires may be damaged by the airbag deployment, so use unneeded tires.
      2. Do not place the SST connector under the tire because it could be damaged.

    3. C107322
      Tie the tires together with the 2 wires.

      CAUTION:
      Make sure that the wires are tight. Looseness in the wires results in the tires breaking loose due to the shock when the airbag is deployed.

  1. Deploy the airbag.

    1. C111072E09
      Connect the red clip of SST to the battery positive (+) terminal and the black clip of SST to the negative (-) terminal.

    2. Check that no one is within a 10 m (33 ft.) radius of the wheel which the steering pad is tied to.

    3. Press the SST activation switch and deploy the airbag.

      CAUTION:
      When deploying the airbag, make sure that no one is near the tire.

      HINT:
      The airbag is deployed as the LED of the SST activation switch comes on.

  1. C051699E01
    Dispose of the steering pad.

    CAUTION:
    1. The steering pad becomes extremely hot when the airbag is deployed, so do not touch it for at least 30 minutes after deployment.
    2. Use gloves and safety glasses when handling a steering pad with a deployed airbag.
    3. Do not apply water, etc. to a steering pad with a deployed airbag.
    4. Always wash your hands with water after completing the operation.


    1. Remove the steering pad from the wheel.

    2. Place the steering pad in a plastic bag, tie it tightly and dispose of it according to local regulations.

← DISPOSAL (Aug 2008 – Jun 2010)COMPONENTS (from May 2007) →