2007-2013 Highlander Kluger · Service Manual RESTRAINTS

REMOVAL

Removal / installation · Vehicles built Aug 2008 – Jun 2010

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010


1. PRECAUTION

CAUTION:
Be sure to read "PRECAUTION" thoroughly before servicing (Click here).


2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait for at least 90 seconds after disconnecting the cable to prevent airbag deployment.

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


3. REMOVE FRONT DOOR SCUFF PLATE LH

  1. B173224
    Disengage the 8 claws and guide, and remove the front door scuff plate LH.


4. REMOVE COWL SIDE TRIM SUB-ASSEMBLY LH

  1. B173227
    Remove the clip.

  1. Disengage the clip and claw, and remove the cowl side trim sub-assembly LH.


5. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY (for Manual Air Conditioning System)

  1. B168371
    Remove the 2 bolts <B>.

  1. Disengage the 3 claws and 10 clips.

  1. Disconnect each connector.

  1. Disconnect the hood lock control cable assembly and remove the lower instrument panel finish panel sub-assembly.


6. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY (for Automatic Air Conditioning System)

  1. B173021
    Remove the 2 bolts <B>.

  1. Disengage the 3 claws and 10 clips.

  1. B173009
    Disconnect each connector and the aspirator duct.

  1. Disconnect the hood lock control cable assembly and remove the lower instrument panel finish panel sub-assembly.


7. REMOVE FRONT DOOR SCUFF PLATE RH

HINT:
Use the same procedure for the RH side and the LH side (Click here).


8. REMOVE COWL SIDE TRIM SUB-ASSEMBLY RH

HINT:
Use the same procedure for the RH side and the LH side (Click here).


9. REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

  1. B172999
    Disengage the 3 claws.

  1. Disengage the 2 guides and remove the No. 2 instrument panel under cover sub-assembly.


10. REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY

  1. B168370
    Remove the 2 bolts <B> and 3 screws <F>.

  1. Disengage the 4 claws and 3 clips.

  1. Disconnect each connector and clamp, and remove the lower instrument panel sub-assembly.


11. REMOVE CENTER INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY (w/o Smart Entry and Start System)

  1. B184678E01
    Apply protective tape to the areas shown in the illustration.

  1. Using a moulding remover, disengage the 10 claws and 8 clips starting from the upper part of the center instrument cluster finish panel assembly.

    NOTICE:
    Do not pull on the small storage compartment lid. Doing so may cause damage.

  1. Disconnect each connector and remove the center instrument cluster finish panel assembly.


12. REMOVE CENTER INSTRUMENT CLUSTER FINISH PANEL ASSEMBLY (w/ Smart Entry and Start System)

  1. B184680E01
    Apply protective tape to the areas shown in the illustration.

  1. Using a moulding remover, disengage the 10 claws and 8 clips starting from the upper part of the center instrument cluster finish panel assembly.

    NOTICE:
    Do not pull on the small storage compartment lid. Doing so may cause damage.

  1. Disconnect each connector and remove the center instrument cluster finish panel assembly.


13. REMOVE UPPER CONSOLE PANEL SUB-ASSEMBLY

  1. B168372
    Disengage the 4 claws and 4 clips.

  1. Disconnect the connector and remove the upper console panel sub-assembly.


14. REMOVE NO. 2 CONSOLE BOX DUCT (w/o Rear Air Conditioning System)

  1. B173012
    Remove the No. 2 console box duct as shown in the illustration.


15. REMOVE LOWER REAR CONSOLE BOX
  1. Remove the lower rear console box.


16. REMOVE CONSOLE BOX ASSEMBLY (w/o Rear Air Conditioning System)

  1. B173628
    Remove the 4 bolts and 2 screws.

  1. B173629
    Disengage the 6 claws and remove the console box assembly.


17. REMOVE CONSOLE BOX ASSEMBLY (w/ Rear Air Conditioning System)

  1. B181135
    Remove the 4 bolts and 2 screws.

  1. B175149
    Disconnect the connector.

  1. Disengage the 6 claws, and remove the console box assembly.


18. REMOVE FRONT NO. 1 CONSOLE BOX INSERT (for LHD)

  1. B168373
    Using a clip remover, remove the 2 clips.

  1. Remove the 3 screws <F>.

  1. Disengage the claw and 2 guides, and then remove the front No. 1 console box insert.


19. REMOVE FRONT NO. 1 CONSOLE BOX INSERT (for RHD)

  1. B173037
    Using a clip remover, remove the clip.

  1. Remove the 3 screws <F>.

  1. Disengage the claw and 2 guides, and then remove the front No. 1 console box insert.


20. REMOVE FRONT NO. 2 CONSOLE BOX INSERT (for LHD)

  1. B168374
    Using a clip remover, remove the clip.

  1. Remove the 3 screws <F>.

  1. Disengage the claw and 2 guides, and then remove the front No. 2 console box insert.


21. REMOVE FRONT NO. 2 CONSOLE BOX INSERT (for RHD)

  1. B173038
    Using a clip remover, remove the clip.

  1. Remove the 3 screws <F>.

  1. Disengage the claw and 2 guides, and then remove the front No. 2 console box insert.


22. REMOVE CENTER AIRBAG SENSOR ASSEMBLY

  1. C165110
    Disconnect the holder (with connectors).

    NOTICE:
    When handling the airbag connector, take care not to damage the airbag wire harness.

  1. Remove the 3 bolts and center airbag sensor assembly.

← REMOVAL (May 2007 – Jul 2008)REMOVAL (from Jul 2010) →