2007-2013 Highlander Kluger · Service Manual BODY

DISASSEMBLY

Removal / installation · Vehicles built from Jul 2010

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010


1. REMOVE VERTICAL SEAT ADJUSTER KNOB

  1. B174621E01
    Using a screwdriver wrapped with protective tape, remove the snap ring as shown in the illustration.

    NOTICE:
    Be careful not to lose the snap ring.

  1. Remove the vertical seat adjuster knob.


2. REMOVE RECLINING ADJUSTER RELEASE HANDLE

  1. B174603E01
    Using a screwdriver wrapped with protective tape, disengage the claw and remove the reclining adjuster release handle.


3. REMOVE VERTICAL ADJUSTER COVER

  1. B174604E01
    Using a screwdriver wrapped with protective tape, disengage the 2 claws and remove the vertical adjuster cover.


4. REMOVE VERTICAL ADJUSTING HANDLE

  1. B174605
    Remove the 2 screws and the vertical adjusting handle.


5. REMOVE FRONT SEAT CUSHION SHIELD

  1. B180387
    Disengage the hooks.

  1. B174606
    Remove the 3 screws.

  1. Disengage the claw.

  1. Disengage the 2 guides and remove the front seat cushion shield.


6. REMOVE FRONT SEAT INNER BELT ASSEMBLY
  1. Disconnect each connector and clamp.

  1. B170882
    Remove the nut and the front seat inner belt assembly.


7. REMOVE FRONT SEAT CUSHION INNER SHIELD

  1. B174623
    Remove the screw.

  1. Disengage the claw.

  1. B174624
    Separate the guide and remove the front seat cushion inner shield as shown in the illustration.


8. REMOVE FRONT SEAT CUSHION COVER WITH PAD

  1. B174625
    w/ Front Seat Side Airbag:
    Disengage the clamp.

  1. for Front Passenger Side:

    1. B174642
      w/ Occupant Classification System:
      Disconnect the occupant detection sensor connector as shown in the illustration.

  1. Using a clip remover, remove the 2 clips.

    B174627

  1. Disengage the hooks and remove the front seat cushion cover with pad as shown in the illustration.


9. REMOVE SEPARATE TYPE FRONT SEAT CUSHION COVER

  1. B172860
    Remove the 6 hog rings.

  1. B172861
    Remove the 11 hog rings and the separate type front seat cushion cover.


10. REMOVE FRONT SEATBACK COVER WITH PAD

  1. B174628
    Remove the 3 hog rings.

  1. B174629
    Remove the 5 hog rings.

  1. B174630
    Remove the 2 hooks.

  1. B174631E01
    w/ Front Seat Side Airbag:
    Turn back the separate type front seatback cover to remove the nut, and separate the bracket of the separate type front seatback cover.

  1. B172866
    Disengage the 4 claws and remove the 2 front seat headrest supports.

  1. Remove the separate type front seatback cover with pad from the front seat frame assembly with adjuster.


11. REMOVE SEPARATE TYPE FRONT SEATBACK COVER

  1. B172868
    Remove the 7 hog rings and the separate type front seatback cover.


12. REMOVE ACTIVE HEADREST UPPER UNIT

  1. B176345
    Remove the nut and disconnect the cable from the active headrest upper unit as shown in the illustration.

  1. Remove the 4 nuts and the active headrest upper unit.


13. REMOVE ACTIVE HEADREST LOWER UNIT

  1. B176346
    Remove the 4 nuts and the active headrest lower unit.


14. REMOVE RECLINING ADJUSTER INSIDE COVER LH

  1. B174607E01
    Remove the screw.

  1. w/ Front Seat Side Airbag:
    Disengage the clamp.

  1. Disengage the guide and remove the reclining adjuster inside cover LH.


15. REMOVE RECLINING ADJUSTER INSIDE COVER LH

  1. B174609
    Remove the screw.

  1. Disengage the claw and remove the reclining adjuster inside cover LH.


16. REMOVE RECLINING ADJUSTER INSIDE COVER RH

  1. B174608
    Remove the screw.

  1. Disengage the guide and remove the reclining adjuster inside cover RH.


17. REMOVE RECLINING ADJUSTER INSIDE COVER RH

  1. B174610
    Remove the screw.

  1. Disengage the claw and remove the reclining adjuster inside cover RH.


18. REMOVE FRONT SEAT AIRBAG ASSEMBLY

  1. C223333
    Disengage the 2 clamps and separate the airbag wire harness.

  1. Remove the 2 nuts and front seat airbag assembly.

    CAUTION:
    1. The nuts must not be reused.
    2. Make sure that the seat frame assembly is not deformed. If it is, replace it with a new one.


19. REMOVE FRONT SEAT LOWER CUSHION SHIELD LH

  1. B174611
    Remove the screw.

  1. Disengage the claw and remove the front seat lower cushion shield LH as shown in the illustration.


20. REMOVE FRONT SEAT LOWER CUSHION SHIELD RH

  1. B174612
    Remove the screw.

  1. Disengage the claw and the guide, and remove the front seat lower cushion shield RH as shown in the illustration.


21. REMOVE SEAT POSITION SENSOR

  1. C166974
    Disconnect the connector.

  1. Using a "TORX" socket wrench (T30), remove the "TORX" screw and seat position sensor with the seat slide position sensor protector.

  1. C133892
    Remove the seat position sensor from the seat slide position sensor protector as shown in the illustration.

← DISASSEMBLY (Aug 2008 – Jun 2010)REASSEMBLY (May 2007 – Jul 2008) →