2007-2013 Highlander Kluger · Service Manual BODY

REASSEMBLY

Removal / installation · Vehicles built from Jul 2010

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010


1. INSTALL SEAT POSITION SENSOR

  1. C168034
    Install the seat position sensor to the seat slide position sensor protector with the pin as shown in the illustration.

  1. C107067E10
    Using a 1.3 mm (0.051 in.) feeler gauge, temporarily install the seat position sensor.

    NOTICE:
    1. If the seat position sensor has been dropped, or there are any cracks, dents or other defects in the case or connector, replace the seat position sensor with a new one.
    2. When installing the seat position sensor, be careful that the SRS wiring does not interfere with other parts and that it is not pinched between other parts.

    HINT:
    Be sure that the clearance between the seat position sensor and the seat rail is within 0.6 mm (0.024 in.) to 2.0 mm (0.079 in.).

  1. C166974
    Using a "TORX" socket wrench (T30), tighten the "TORX" screw to install the seat position sensor.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Make sure that the clearance between the seat position sensor and the seat rail is within 0.6 mm (0.024 in.) to 2.0 mm (0.079 in.).

  1. Check that there are no loose parts after installing the seat position sensor.

  1. Connect the connector.


2. INSTALL FRONT SEAT LOWER CUSHION SHIELD RH

  1. B174617
    Engage the guide and the claw.

  1. Install the front seat lower cushion shield RH with the screw.


3. INSTALL FRONT SEAT LOWER CUSHION SHIELD LH

  1. B174616
    Engage the claw.

  1. Install the front seat lower cushion shield LH with the screw.


4. INSTALL FRONT SEAT AIRBAG ASSEMBLY

CAUTION:
  1. The nuts must not be reused.
  2. Make sure that the seat frame assembly is not deformed. If it is, replace it with a new one.

  1. C223333
    Install the front seat airbag assembly with 2 new nuts.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

  1. Engage the 2 clamps to connect the wire harness.


5. INSTALL RECLINING ADJUSTER INSIDE COVER RH

  1. B174610
    Engage the claw.

  1. Install the reclining adjuster inside cover RH with the screw.


6. INSTALL RECLINING ADJUSTER INSIDE COVER RH

  1. B174608
    Engage the guide.

  1. Install the reclining adjuster inside cover RH with the screw.


7. INSTALL RECLINING ADJUSTER INSIDE COVER LH

  1. B174609
    Engage the claw.

  1. Install the reclining adjuster inside cover LH with the screw.


8. INSTALL RECLINING ADJUSTER INSIDE COVER LH

  1. B174607E01
    Engage the guide.

  1. w/ Front Seat Side Airbag:
    Engage the clamp.

  1. Install the reclining adjuster inside cover LH with the screw.


9. INSTALL ACTIVE HEADREST LOWER UNIT

  1. B176346
    Install the active headrest lower unit with the 4 nuts.

    Torque:
    8.5 N*m{ 87 kgf*cm , 75 in.*lbf }


10. INSTALL ACTIVE HEADREST UPPER UNIT

  1. B176345
    Install the active headrest upper unit with the 4 nuts.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }

  1. Connect the cable to the active headrest upper unit with the nut as shown in the illustration.

    Torque:
    8.5 N*m{ 87 kgf*cm , 75 in.*lbf }


11. INSTALL SEPARATE TYPE FRONT SEATBACK COVER

  1. B173750E01
    Using hog ring pliers, install the separate type front seatback cover with 7 new hog rings.

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, take care to minimize wrinkles as much as possible.


12. INSTALL FRONT SEATBACK COVER WITH PAD
  1. Temporarily install the front seatback cover with pad to the front seat frame assembly with adjuster.

  1. B172866
    Engage the 4 claws and install the 2 front seat headrest supports.

  1. B174631E01
    w/ Front Seat Side Airbag:
    Install the front seatback cover bracket with the nut.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }

    NOTICE:
    1. For vehicles with side airbags, the side airbags may not be activated normally unless the front seatback cover is securely installed.
    2. Check that the strap is not twisted after installing the bracket.
    3. Install the bracket securely.

  1. B174634E01
    Using hog ring pliers, install 5 new hog rings.

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, take care to minimize wrinkles as much as possible.

  1. B174635E01
    Using hog ring pliers, install the front seatback cover with pad with 3 new hog rings.

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, take care to minimize wrinkles as much as possible.


13. INSTALL SEPARATE TYPE FRONT SEAT CUSHION COVER

  1. B173751E01
    Using hog ring pliers, install the separate type front seat cushion cover with 11 new hog rings.

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, take care to minimize wrinkles as much as possible.

  1. B173749E01
    Using hog ring pliers, install the separate type front seat cushion cover with 6 new hog rings.


14. INSTALL FRONT SEAT CUSHION COVER WITH PAD
  1. Temporarily install the front seat cushion cover with pad to the front seat frame assembly with adjuster.

  1. Engage the hooks.

    B174636

  1. Install the front seat cushion cover with pad with the 2 clips.

  1. for Front Passenger Side:

    1. B174643
      w/ Occupant Classification System:
      Connect the occupant detection sensor connector as shown in the illustration.

  1. B174625
    w/ Front Seat Side Airbag:
    Engage the clamp.


15. INSTALL FRONT SEAT CUSHION INNER SHIELD

  1. B174637
    Insert the guide and temporarily install the front seat cushion inner shield.

  1. B174623
    Engage the claw.

  1. Install the front seat cushion inner shield with the screw.


16. INSTALL FRONT SEAT INNER BELT ASSEMBLY

  1. B170883E01
    Install the front seat inner belt assembly with the nut.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    NOTICE:
    Do not allow the anchor part of the front seat inner belt assembly to overlap the protruding part of the front seat adjuster.

  1. Connect each connector and clamp.


17. INSTALL FRONT SEAT CUSHION SHIELD

  1. B174606
    Engage the 2 guides.

  1. Engage the claw.

  1. Install the front seat cushion shield with the 3 screws.

  1. B180387
    Engage the hooks.


18. INSTALL VERTICAL ADJUSTING HANDLE

  1. B174605
    Install the vertical adjusting handle with the 2 screws.


19. INSTALL VERTICAL ADJUSTER COVER

  1. B174619
    Engage the 2 claws and install the vertical adjuster cover.


20. INSTALL RECLINING ADJUSTER RELEASE HANDLE

  1. B174618
    Engage the claw and install the reclining adjuster release handle.


21. INSTALL VERTICAL SEAT ADJUSTER KNOB

  1. B174622E01
    Install the snap ring to the vertical seat adjuster knob as shown in the illustration.

  1. Install the vertical seat adjuster knob.

← REASSEMBLY (Aug 2008 – Jun 2010)INSTALLATION (May 2007 – Jul 2008) →