2007-2013 Highlander Kluger · Service Manual BODY ELECTRICAL

Only Passenger Door LOCK / UNLOCK Functions do not Operate

Circuit diagnosis · Vehicles built May 2007 – Jul 2008

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010

DESCRIPTION

The main body ECU (instrument panel junction block) receives lock/unlock switch signals and activates the door lock motor according to these signals.

WIRING DIAGRAM

B164398E23
B164398E24

INSPECTION PROCEDURE


1. INSPECT FRONT DOOR LOCK ASSEMBLY

  1. Remove the front passenger side door lock assembly (Click here).B164413E02

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Measurement Condition
    Door Lock Condition
    Specified Condition
    7 - 8
    Battery positive (+) → Terminal 4
    Battery negative (-) → Terminal 1
    Locked
    10 kΩ or higher
    7 - 8
    Battery positive (+) → Terminal 1
    Battery negative (-) → Terminal 4
    Unlocked
    Below 1 Ω



NG
REPLACE FRONT DOOR LOCK ASSEMBLY (Click here)
OK


2. CHECK HARNESS AND CONNECTOR (FRONT DOOR LOCK MOTOR CIRCUIT)
  1. Disconnect the instrument panel junction block connector.

  1. for LHD:

    1. B171380E01
      Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      Tester Connection
      Condition
      Specified Condition
      G8-1 (UL) - 1J-2
      Always
      Below 1 Ω
      G8-4 (L) - 1J-1
      Always
      Below 1 Ω
      G8-1 (UL) - Body ground
      Always
      10 kΩ or higher
      G8-4 (L) - Body ground
      Always
      10 kΩ or higher

  1. for RHD:

    1. Measure the resistance according to the value(s) in the table below.B178842E02

      Standard resistance:
      Tester Connection
      Condition
      Specified Condition
      H6-1 (UL) - 1J-2
      Always
      Below 1 Ω
      H6-4 (L) - 1K-2
      Always
      Below 1 Ω
      H6-1 (UL) - Body ground
      Always
      10 kΩ or higher
      H6-4 (L) - Body ground
      Always
      10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. CHECK HARNESS AND CONNECTOR (DOOR UNLOCK DETECTION SWITCH CIRCUIT)
  1. Disconnect the main body ECU (instrument panel junction block) connector.

  1. for LHD:

    1. B111708E35
      Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      Tester Connection
      Condition
      Specified Condition
      G8-7 (LSSR) - D6-27 (LSWP)
      Always
      Below 1 Ω
      G8-7 (LSSR) - Body ground
      Always
      10 kΩ or higher
      G8-8 (E) - Body ground
      Always
      Below 1 Ω

  1. for RHD:

    1. B111708E36
      Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      Tester Connection
      Condition
      Specified Condition
      H6-8 (LSSR) - D6-27 (LSWP)
      Always
      Below 1 Ω
      H6-8 (LSSR) - Body ground
      Always
      10 kΩ or higher
      H6-7 (E) - Body ground
      Always
      Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU (INSTRUMENT PANEL JUNCTION BLOCK)


← Only Driver Door LOCK / UNLOCK Functions do not Operate (from Jul 2010)Only Passenger Door LOCK / UNLOCK Functions do not Operate (Aug 2008 – Jun 2010) →