DATA LIST / ACTIVE TEST
System information · Vehicles built May 2007 – Jul 2008
Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010
| DATA LIST |
- HINT:
- Using Intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
- NOTICE:
- In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Warm up the engine.
Turn the ignition switch off.
Connect Intelligent tester to the DLC3.
Turn the ignition switch on (IG).
Turn on the tester.
Select the item "Powertrain / Engine and ECT / Data List".
According to the display on the tester, read the "Data List".
Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Stop Light Switch
Stop light switch Status/
ON or OFF
Brake Pedal is depressed: ON
Brake Pedal is released: OFF
-
Neutral Position SW Signal
PNP switch Status/
ON or OFF
Shift lever position is:
P and N: ON
Except P and N: OFF
When the shift lever position displayed on Intelligent tester differs from the actual position, adjustment of the PNP switch or the shift cable may be incorrect. - HINT:
- When the failure still occurs even after adjusting these parts, Click here.
Shift SW Status (P Range)
PNP switch Status/
ON or OFF
Shift lever position is:
P: ON
Except P: OFF
↑
Shift SW Status (N Range)
PNP switch Status/
ON or OFF
Shift lever position is:
N: ON
Except N: OFF
↑
Shift SW Status (R Range)
PNP switch Status/
ON or OFF
Shift lever position is:
R: ON
Except R: OFF
↑
Shift SW Status (D Range)
PNP switch Status/
ON or OFF
Shift lever position is:
D, and S : ON
Except D, and S: OFF
↑
Sports Mode Selection SW
Sport Mode Select switch Status/
ON or OFF
Shift lever position is:
S, "+" and "-": ON
Except S, "+" and "-": OFF
-
Sports Shift Up SW
Sport Shift Up switch Status/
ON or OFF
Press continuously "+" (Up shift): ON
Release "+" (Up shift): OFF
-
Sports Shift Down SW
Sport Shift Down switch Status/
ON or OFF
Press continuously "-" (Down shift): ON
Release "-" (Down shift): OFF
-
Shift Status
Actual Gear Position/
1st, 2nd, 3rd, 4th or 5th
Shift Lever Position is:
D: 1st, 2nd, 3rd, 4th or 5th
S: 1st, 2nd, 3rd, 4th or 5th
-
Lock Up
Lock Up Status/
ON or OFF
Lock Up: ON
Except Lock Up: OFF
-
Lock Up Solenoid Status
Lock Up Solenoid Status/
ON or OFF
Lock Up Solenoid: ON
Except Lock Up Solenoid: OFF
-
SLT Solenoid Status
Shift Solenoid SLT Status/
ON or OFF
Accelerator pedal is depressed: OFF
Accelerator pedal is released: ON
-
A/T Oil Temperature 1
ATF Temp. Sensor Value/
min.: -40°C (-40°F)
max.: 215°C (419°F)
After Stall Test:
Approx. 80°C (176°F)
Equal to ambient temperature when cold soak
If the value is "-40°C (-40°F)" or "215°C (419°F)", ATF temp. sensor circuit is opened or shorted.
SPD (NC)
Counter Gear Speed/
display: 50 r/min
- HINT:
- 3rd when shift lever position is D position (After warming up the engine):
- Intermediate shaft speed (NC) becomes close to the engine speed.
- Intermediate shaft speed (NC) becomes close to the engine speed.
-
SPD (NT)
Input Turbine Speed/display: 50 r/min
- HINT:
- Lock-up ON (After warming up the engine):
Input Turbine speed (NT) equal to the engine speed.
- Lock-up OFF (Idling at N position):
Input Turbine speed (NT) nearly equal to the engine speed.
- Lock-up ON (After warming up the engine):
-
Snow Switch Status
Pattern SW (ECT SNOW) status/ ON or OFF
Engine switch ON: OFF
↓
Pattern switch (ECT SNOW) Push: ON
↓
Pattern switch (ECT SNOW) Push: OFF
-
| ACTIVE TEST |
- HINT:
- Using Intelligent tester to perform Active Test allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Test early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Test.
Warm up the engine.
Turn the ignition switch off.
Connect Intelligent tester to the DLC3.
Turn the ignition switch on (IG).
Push the "ON" button of Intelligent tester.
Select the item "Powertrain / Engine and ECT / Active Test".
According to the display on tester, perform the "Active Test".
*: "Activate the Solenoid (SLT)" in the Active Test is performed to check the line pressure changes by connecting the SST to the automatic transaxle, which is used in the HYDRAULIC TEST (Click here) as well.Tester Display
Test Part
Control Range
Diagnostic Note
Control the Shift Position
[Test Details]
Operate the shift solenoid valve and set each shift position by yourself.
[Vehicle Condition]- IDL: ON
- Less than 50 km/h (31 mph)
- Press "→" button: Shift up
- Press "←" button: Shift down
1st/2nd/3rd/4th/5th
Possible to check the operation of the shift solenoid valves.
Activate the Lock Up
[Test Details]
Control the shift solenoid DSL to set the automatic transaxle to the lock-up condition.
[Vehicle Condition]- Throttle valve opening angle: Less than 35 %
- Vehicle Speed: 60 km/h (37 mph) or more
ON/OFF
Possible to check the DSL operation.
Activate the Solenoid (SL1)
[Test Details]
Operate the shift solenoid SL1
[Vehicle Condition]- Vehicle Stopped.
- Shift lever P or N position
ON/OFF
-
Activate the Solenoid (SL2)
[Test Details]
Operate the shift solenoid SL2
[Vehicle Condition]- Vehicle Stopped.
- Shift lever P or N position
ON/OFF
-
Activate the Solenoid (SL3)
[Test Details]
Operate the shift solenoid SL3
[Vehicle Condition]- Vehicle Stopped.
- Shift lever P or N position
ON/OFF
-
Activate the Solenoid (S4)
[Test Details]
Operate the shift solenoid S4
[Vehicle Condition]- Vehicle Stopped.
- Shift lever P or N position
ON/OFF
-
Activate the Solenoid (SR)
[Test Details]
Operate the shift solenoid SR
[Vehicle Condition]- Vehicle Stopped.
- Shift lever P or N position
ON/OFF
-
Activate the Solenoid (DSL)
[Test Details]
Operate the shift solenoid DSL
[Vehicle Condition]- Vehicle Stopped.
- Shift lever P or N position
ON/OFF
-
Activate the Solenoid (SLT)*
[Test Details]
Operate the shift solenoid SLT and raise the line pressure.
[Vehicle Condition]- Vehicle Stopped.
- IDL: ON
- HINT:
- OFF: Line pressure up (When the active test of "Activate the Solenoid (SLT)" is performed, the ECM commands the SLT solenoid to turn off).
- ON: No action (normal operation)
ON/OFF
-
- HINT:
- The pressure values in Active Test and HYDRAULIC TEST are different from each other.
- IDL: ON