2007-2013 Highlander Kluger · Service Manual TRANSMISSION

DATA LIST / ACTIVE TEST

System information · Vehicles built May 2007 – Jul 2008

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010


DATA LIST

HINT:
Using Intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Warm up the engine.

  2. Turn the ignition switch off.

  3. Connect Intelligent tester to the DLC3.

  4. Turn the ignition switch on (IG).

  5. Turn on the tester.

  6. Select the item "Powertrain / Engine and ECT / Data List".

  7. According to the display on the tester, read the "Data List".

    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Stop Light Switch
    Stop light switch Status/
    ON or OFF
    Brake Pedal is depressed: ON
    Brake Pedal is released: OFF
    -
    Neutral Position SW Signal
    PNP switch Status/
    ON or OFF
    Shift lever position is:
    P and N: ON
    Except P and N: OFF
    When the shift lever position displayed on Intelligent tester differs from the actual position, adjustment of the PNP switch or the shift cable may be incorrect.

    HINT:
    When the failure still occurs even after adjusting these parts, Click here.

    Shift SW Status (P Range)
    PNP switch Status/
    ON or OFF
    Shift lever position is:
    P: ON
    Except P: OFF
    ↑
    Shift SW Status (N Range)
    PNP switch Status/
    ON or OFF
    Shift lever position is:
    N: ON
    Except N: OFF
    ↑
    Shift SW Status (R Range)
    PNP switch Status/
    ON or OFF
    Shift lever position is:
    R: ON
    Except R: OFF
    ↑
    Shift SW Status (D Range)
    PNP switch Status/
    ON or OFF
    Shift lever position is:
    D, and S : ON
    Except D, and S: OFF
    ↑
    Sports Mode Selection SW
    Sport Mode Select switch Status/
    ON or OFF
    Shift lever position is:
    S, "+" and "-": ON
    Except S, "+" and "-": OFF
    -
    Sports Shift Up SW
    Sport Shift Up switch Status/
    ON or OFF
    Press continuously "+" (Up shift): ON
    Release "+" (Up shift): OFF
    -
    Sports Shift Down SW
    Sport Shift Down switch Status/
    ON or OFF
    Press continuously "-" (Down shift): ON
    Release "-" (Down shift): OFF
    -
    Shift Status
    Actual Gear Position/
    1st, 2nd, 3rd, 4th or 5th
    Shift Lever Position is:
    D: 1st, 2nd, 3rd, 4th or 5th
    S: 1st, 2nd, 3rd, 4th or 5th
    -
    Lock Up
    Lock Up Status/
    ON or OFF
    Lock Up: ON
    Except Lock Up: OFF
    -
    Lock Up Solenoid Status
    Lock Up Solenoid Status/
    ON or OFF
    Lock Up Solenoid: ON
    Except Lock Up Solenoid: OFF
    -
    SLT Solenoid Status
    Shift Solenoid SLT Status/
    ON or OFF
    Accelerator pedal is depressed: OFF
    Accelerator pedal is released: ON
    -
    A/T Oil Temperature 1
    ATF Temp. Sensor Value/
    min.: -40°C (-40°F)
    max.: 215°C (419°F)
    After Stall Test:
    Approx. 80°C (176°F)
    Equal to ambient temperature when cold soak
    If the value is "-40°C (-40°F)" or "215°C (419°F)", ATF temp. sensor circuit is opened or shorted.
    SPD (NC)
    Counter Gear Speed/
    display: 50 r/min

    HINT:
    3rd when shift lever position is D position (After warming up the engine):
    1. Intermediate shaft speed (NC) becomes close to the engine speed.

    -
    SPD (NT)
    Input Turbine Speed/display: 50 r/min

    HINT:
    1. Lock-up ON (After warming up the engine):
      Input Turbine speed (NT) equal to the engine speed.
    2. Lock-up OFF (Idling at N position):
      Input Turbine speed (NT) nearly equal to the engine speed.

    -
    Snow Switch Status
    Pattern SW (ECT SNOW) status/ ON or OFF
    Engine switch ON: OFF
    ↓
    Pattern switch (ECT SNOW) Push: ON
    ↓
    Pattern switch (ECT SNOW) Push: OFF
    -


ACTIVE TEST

HINT:
Using Intelligent tester to perform Active Test allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Test early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Test.

  1. Warm up the engine.

  2. Turn the ignition switch off.

  3. Connect Intelligent tester to the DLC3.

  4. Turn the ignition switch on (IG).

  5. Push the "ON" button of Intelligent tester.

  6. Select the item "Powertrain / Engine and ECT / Active Test".

  7. According to the display on tester, perform the "Active Test".

    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Control the Shift Position
    [Test Details]
    Operate the shift solenoid valve and set each shift position by yourself.
    [Vehicle Condition]
    1. IDL: ON
    2. Less than 50 km/h (31 mph)
    [Others]
    1. Press "→" button: Shift up
    2. Press "←" button: Shift down
    1st/2nd/3rd/4th/5th
    Possible to check the operation of the shift solenoid valves.
    Activate the Lock Up
    [Test Details]
    Control the shift solenoid DSL to set the automatic transaxle to the lock-up condition.
    [Vehicle Condition]
    1. Throttle valve opening angle: Less than 35 %
    2. Vehicle Speed: 60 km/h (37 mph) or more
    ON/OFF
    Possible to check the DSL operation.
    Activate the Solenoid (SL1)
    [Test Details]
    Operate the shift solenoid SL1
    [Vehicle Condition]
    1. Vehicle Stopped.
    2. Shift lever P or N position
    ON/OFF
    -
    Activate the Solenoid (SL2)
    [Test Details]
    Operate the shift solenoid SL2
    [Vehicle Condition]
    1. Vehicle Stopped.
    2. Shift lever P or N position
    ON/OFF
    -
    Activate the Solenoid (SL3)
    [Test Details]
    Operate the shift solenoid SL3
    [Vehicle Condition]
    1. Vehicle Stopped.
    2. Shift lever P or N position
    ON/OFF
    -
    Activate the Solenoid (S4)
    [Test Details]
    Operate the shift solenoid S4
    [Vehicle Condition]
    1. Vehicle Stopped.
    2. Shift lever P or N position
    ON/OFF
    -
    Activate the Solenoid (SR)
    [Test Details]
    Operate the shift solenoid SR
    [Vehicle Condition]
    1. Vehicle Stopped.
    2. Shift lever P or N position
    ON/OFF
    -
    Activate the Solenoid (DSL)
    [Test Details]
    Operate the shift solenoid DSL
    [Vehicle Condition]
    1. Vehicle Stopped.
    2. Shift lever P or N position
    ON/OFF
    -
    Activate the Solenoid (SLT)*
    [Test Details]
    Operate the shift solenoid SLT and raise the line pressure.
    [Vehicle Condition]
    1. Vehicle Stopped.
    2. IDL: ON

    HINT:
    OFF: Line pressure up (When the active test of "Activate the Solenoid (SLT)" is performed, the ECM commands the SLT solenoid to turn off).
    ON: No action (normal operation)

    ON/OFF
    -
    *: "Activate the Solenoid (SLT)" in the Active Test is performed to check the line pressure changes by connecting the SST to the automatic transaxle, which is used in the HYDRAULIC TEST (Click here) as well.

    HINT:
    The pressure values in Active Test and HYDRAULIC TEST are different from each other.

← FAIL-SAFE CHART (from May 2007)DATA LIST / ACTIVE TEST (Aug 2008 – Jun 2010) →