2007-2013 Highlander Kluger · Service Manual STEERING

INSTALLATION

Removal / installation · Vehicles built Aug 2008 – Jun 2010

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010


1. INSTALL STEERING INTERMEDIATE SHAFT SUB-ASSEMBLY

  1. C166132E01
    Align the matchmarks on the steering intermediate shaft sub-assembly and the steering column assembly.

  1. C166131
    Install a new bolt.

    Torque:
    35 N*m{ 360 kgf*cm , 26 ft.*lbf }


2. INSTALL STEERING COLUMN ASSEMBLY (for LHD)

  1. C166135E01
    Check that the 2 bushings are securely installed to the steering column assembly.

    HINT:
    If the bushings are missing or damaged, replace the steering column assembly with a new one.

  1. C166130
    Install the steering column assembly with the bolt and 2 nuts.

    Torque:
    Bolt:
    36 N*m{ 367 kgf*cm , 27 ft.*lbf }
    Nut:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf }

    NOTICE:
    There are two different bolt sizes (12 mm (0.472 in.) or 14 mm (0.551 in.)) available.

  1. Connect the connectors and engage the wire harness clamps to the steering column assembly.

  1. C166140
    Connect the connector to the power steering ECU assembly.

  1. C166139
    Connect the connector to the power steering ECU assembly.

    HINT:
    As shown in the illustration, securely return the lock lever to its original position to connect the connector.


3. INSTALL STEERING COLUMN ASSEMBLY (for RHD)

  1. C166135E01
    Check that the 2 bushings are securely installed to the steering column assembly.

    HINT:
    If the bushings are missing or damaged, replace the steering column assembly with a new one.

  1. C168095
    Install the steering column assembly with the bolt and 2 nuts.

    Torque:
    Bolt:
    36 N*m{ 367 kgf*cm , 27 ft.*lbf }
    Nut:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf }

    NOTICE:
    There are two different bolt sizes (12 mm (0.472 in.) or 14 mm (0.551 in.)) available.

  1. Connect the connectors and engage the wire harness clamps to the steering column assembly.

  1. C166143
    Connect the connector to the power steering ECU assembly.

  1. C166141
    Connect the connector to the power steering ECU assembly.

    HINT:
    As shown in the illustration, securely return the lock lever to its original position to connect the connector.


4. CONNECT STEERING INTERMEDIATE SHAFT SUB-ASSEMBLY

  1. C165545E01
    Align the matchmarks on the steering intermediate shaft sub-assembly and the power steering link assembly.

  1. C165544
    Install a new bolt.

    Torque:
    35 N*m{ 360 kgf*cm , 26 ft.*lbf }

  1. C166146
    Install the steering intermediate shaft sub-assembly to the steering column hole shield.

  1. C166145
    Tighten the bolt.


5. INSTALL NO. 1 AIR DUCT SUB-ASSEMBLY (for LHD)

  1. C166133
    Engage the 2 claws to install the No. 1 air duct sub-assembly.


6. INSTALL NO. 1 AIR DUCT SUB-ASSEMBLY (for RHD)

  1. C166134
    Engage the 2 claws to install the No. 1 air duct sub-assembly.


7. POSITION FRONT WHEELS STRAIGHT AHEAD

8. INSTALL TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY

  1. C166129
    Using pliers, engage the claw. Install the turn signal switch assembly with spiral cable sub-assembly to the steering column assembly.

  1. Connect the connectors to the turn signal switch assembly with spiral cable sub-assembly.


9. INSTALL STEERING COLUMN COVER

  1. C165716
    Engage the claw to install the upper steering column cover.

  1. C166128
    Engage the 2 claws to install the lower steering column cover.

  1. C165715
    Install the 2 screws.

    Torque:
    2.0 N*m{ 20 kgf*cm , 18 in.*lbf }


10. INSTALL BRAKE PEDAL SUPPORT SUB-ASSEMBLY (for LHD)

  1. C165374
    Install the brake pedal support sub-assembly with the 4 nuts.

    Torque:
    13 N*m{ 132 kgf*cm , 10 ft.*lbf }

  1. C165373
    Install the brake pedal support sub-assembly to the instrument panel reinforcement with the 2 bolts.

    Torque:
    35 N*m{ 357 kgf*cm , 26 ft.*lbf }

  1. C165371
    Connect the brake pedal load sensing switch connector and engage the clamp.


11. INSTALL BRAKE PEDAL SUPPORT SUB-ASSEMBLY (for RHD)

  1. C165376
    Install the brake pedal support sub-assembly with the 4 nuts.

    Torque:
    13 N*m{ 132 kgf*cm , 10 ft.*lbf }

  1. C165375
    Install the brake pedal support sub-assembly to the instrument panel reinforcement with the 2 bolts.

    Torque:
    35 N*m{ 357 kgf*cm , 26 ft.*lbf }

  1. C165372
    Connect the brake pedal load sensing switch connector and engage the clamp.


12. CONNECT BRAKE MASTER CYLINDER PUSH ROD CLEVIS

  1. C166415E01
    Apply lithium soap base glycol grease to the push rod pin.

  1. Connect the brake master cylinder push rod clevis to the brake pedal with the push rod pin, and install a new clip as shown in the illustration.


13. INSTALL BRAKE PEDAL RETURN SPRING

  1. C165369
    Install the brake pedal return spring between the instrument panel reinforcement and brake master cylinder push rod clevis.


14. INSTALL STOP LIGHT SWITCH ASSEMBLY

  1. E150075E01
    Temporarily install the stop light switch assembly with the stop light switch lock nut.

  1. E150611E01
    Turn the stop light switch assembly so that the clearance between the nut end and stop light switch cushion is between 0.5 to 2.4 mm (0.020 to 0.095 in.).

  1. Tighten the stop light switch lock nut.

    Torque:
    17 N*m{ 173 kgf*cm , 12 ft.*lbf }

  1. E150073
    Connect the connector.


15. INSPECT AND ADJUST BRAKE PEDAL HEIGHT

  1. Check the brake pedal height.

    1. C165370E03
      Turn back the carpet.
      Text in Illustration 
      *1
      Stop Light Switch Assembly
      *2
      Clevis Lock Nut
      *3
      Front Floor Footrest (for LHD)
      No. 2 Dash Panel Insulator Pad (for RHD)
      *a
      Brake Pedal Height

    2. Measure the shortest distance between the brake pedal surface and front floor footrest (for LHD) or No. 2 dash panel insulator pad (for RHD).

      Pedal height (for LHD: from front floor footrest, for RHD: from No. 2 dash panel insulator pad) 
      Model
      Specified Condition
      LHD
      148.8 to 158.8 mm (5.858 to 6.252 in.)
      RHD
      165.9 to 175.9 mm (6.531 to 6.925 in.)

  1. Adjust the brake pedal height.

    1. Disconnect the stop light switch connector.

    2. Remove the stop light switch assembly.

    3. Loosen the push rod clevis lock nut.

    4. Adjust the brake pedal height by turning the push rod.

    5. Tighten the push rod clevis lock nut.

      Torque:
      26 N*m{ 265 kgf*cm , 19 ft.*lbf }

    6. Install and adjust the stop light switch (Click here).

      NOTICE:
      Do not depress the brake pedal.

    7. Connect the stop light switch connector.


16. INSPECT BRAKE PEDAL FREE PLAY

  1. C132708E01
    Stop the engine. Depress the pedal several times until no vacuum is left in the brake booster. Release the brake pedal.

  1. Depress the pedal until a slight resistance is felt. Measure the distance as shown in the illustration.

    Pedal free play:
    1.0 to 6.0 mm (0.039 to 0.236 in.)

    If the pedal free play is not as specified, check the stop light switch clearance (Click here). If the pedal free play is as specified, proceed to the "INSPECT BRAKE PEDAL RESERVE DISTANCE" procedure.


17. INSPECT BRAKE PEDAL RESERVE DISTANCE

HINT:
Measure the distance at the same point used for the brake pedal height inspection.

  1. Release the parking brake.

  1. C111339E13
    With the engine running, depress the brake pedal and measure the pedal reserve distance as shown in the illustration.
    Text in Illustration 
    *1
    Front Floor Footrest (for LHD)
    No. 2 Dash Panel Insulator Pad (for RHD)
    *a
    Pedal Reserve Distance

    Pedal reserve distance at 500 N (51 kgf, 112 lbf) (for LHD: from front floor footrest, for RHD: from No. 2 dash panel insulator pad):
    Model
    Specified Condition
    LHD
    84.4 mm (3.32 in.)
    RHD
    97.8 mm (3.85 in.)

    If the distance is not as specified, troubleshoot the brake system (Click here).


18. INSTALL DRIVER SIDE KNEE AIRBAG ASSEMBLY
  1. Check that the ignition switch is off.

  1. Check that the battery negative (-) cable is disconnected.

    CAUTION:
    Wait for at least 90 seconds after disconnecting the cable to prevent airbag deployment.

  1. C165102
    Install the DLC3 to the driver side knee airbag assembly with the 2 claws.

  1. C168061
    Connect the connector to the driver side knee airbag assembly.

    NOTICE:
    When handling the airbag connector, take care not to damage the airbag wire harness.

  1. C168059
    Support the driver side knee airbag assembly with one hand as shown in the illustration.

  1. C165099
    Temporarily install the driver side knee airbag assembly with the 2 hooks.

  1. C165098
    Install the driver side knee airbag assembly with the 4 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }


19. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY (for Manual Air Conditioning System)

  1. B168371
    Connect the hood lock control cable assembly.

  1. Connect each connector.

  1. Engage the 3 claws and 10 clips.

  1. Install the lower instrument panel finish panel sub-assembly with the 2 bolts <B>.


20. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL SUB-ASSEMBLY (for Automatic Air Conditioning System)

  1. B173009
    Connect the hood lock control cable assembly.

  1. Connect each connector and the aspirator duct.

  1. B173021
    Engage the 3 claws and 10 clips.

  1. Install the lower instrument panel finish panel sub-assembly with the 2 bolts <B>.


21. INSTALL COWL SIDE TRIM SUB-ASSEMBLY LH

  1. B173227
    Engage the claw and clip, install the cowl side trim sub-assembly LH.

  1. Install the clip.


22. INSTALL FRONT DOOR SCUFF PLATE LH

  1. B173224
    Engage the guide and the 8 claws, and install the front door scuff plate LH.


23. ADJUST SPIRAL CABLE
  1. Check that the ignition switch is off.

  1. Check that the battery negative (-) cable is disconnected.

    CAUTION:
    Wait for at least 90 seconds after disconnecting the cable to prevent airbag deployment.

  1. C165096
    Rotate the spiral cable counterclockwise slowly by hand until it stops.

    NOTICE:
    Do not turn the spiral cable using the airbag wire harness.

  1. C165097E01
    Rotate the spiral cable clockwise approximately 2.5 turns to align the marks.

    NOTICE:
    Do not turn the spiral cable using the airbag wire harness.

    HINT:
    The spiral cable will rotate approximately 2.5 turns to both the left and right from the center.


24. INSTALL STEERING WHEEL ASSEMBLY

  1. C165708E01
    Align the matchmarks on the steering wheel assembly and steering main shaft.

  1. Install the steering wheel assembly set nut.

    Torque:
    50 N*m{ 510 kgf*cm , 37 ft.*lbf }

  1. Connect the connectors to the spiral cable sub-assembly.


25. INSPECT STEERING WHEEL CENTER POINT

26. INSTALL STEERING PAD
  1. Check that the ignition switch is off.

  1. Check that the battery negative (-) terminal is disconnected.

    CAUTION:
    Wait for at least 90 seconds after disconnecting the cable to prevent airbag deployment.

  1. C165092
    Support the steering pad with one hand as shown in the illustration.

  1. C165093
    Connect the 2 airbag connectors to the steering pad.

    NOTICE:
    When handling the airbag connector, take care not to damage the airbag wire harness.

  1. Connect the horn connector to the steering pad.

  1. Confirm that the circumference groove of the "TORX" screw fits in the screw case, and place the steering pad onto the steering wheel assembly.

  1. C166982E01
    Using a "TORX" socket wrench (T30), tighten the 2 "TORX" screws.

    Torque:
    8.8 N*m{ 90 kgf*cm , 78 in.*lbf }


27. INSTALL LOWER NO. 3 STEERING WHEEL COVER

  1. C165090
    Install the lower No. 3 steering wheel cover with the claw.


28. INSTALL LOWER NO. 2 STEERING WHEEL COVER

  1. C165091
    Install the lower No. 2 steering wheel cover with the claw.


29. INSTALL FRONT WHEEL LH

Torque:
103 N*m{ 1050 kgf*cm , 76 ft.*lbf }


30. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


31. INSPECT STEERING PAD

  1. C166979
    With the steering pad installed on the vehicle, perform a visual check. If there are any defects as mentioned below, replace the steering pad with a new one:
    1. Cuts, minute cracks or marked discoloration on the steering pad top surface or grooves.

  1. Make sure that the horn sounds.

    HINT:
    If the horn does not sound, inspect the horn system (Click here).


32. INSPECT SRS WARNING LIGHT

HINT:
Click here.

← INSTALLATION (May 2007 – Jul 2008)INSTALLATION (from Jul 2010) →