2007-2013 Highlander Kluger · Service Manual ENGINE

MIL Circuit

Circuit diagnosis · Vehicles built May 2007 – Jul 2008

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010

DESCRIPTION

The MIL (Malfunction Indicator Lamp) is used to indicate vehicle malfunctions detected by the ECM. When the ignition switch is turned on (IG), power is supplied to the MIL circuit, and the ECM provides the circuit ground which illuminates the MIL.
The MIL operation can be checked visually. When the ignition switch is first turned on (IG), the MIL should be illuminated and should then turn off. If the MIL remains illuminated or is not illuminated, conduct the following troubleshooting procedure using the intelligent tester.

WIRING DIAGRAM

A172780E02
A141118E04

INSPECTION PROCEDURE


1. CHECK THAT MIL IS ILLUMINATED
  1. Turn the ignition switch on (IG).

  1. Check the illumination of the MIL.

    Result:
    Result
    Proceed to
    MIL remains illuminated (Even after ignition switch is turned on (IG) and several seconds have passed, MIL still remains illuminated)
    A
    MIL remains off (Does not illuminate at all)
    B



B
Go to step 5
A


2. CHECK WHETHER MIL TURNS OFF
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG) and turn the tester on.

  1. Select the following menu items: Powertrain / Engine and ECT / Trouble Code.

  1. Check if any DTCs have been stored. Note down any DTCs.

  1. Clear the DTCs (Click here).

  1. Check if the MIL goes off.

    Standard:
    MIL goes off.



NG
Go to step 3
OK

REPAIR CIRCUITS INDICATED BY OUTPUT DTCS

3. CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT IN WIRE HARNESS)

  1. A163321E05
    Disconnect the ECM connector.

  1. Turn the ignition switch on (IG).

  1. Check that the MIL is not illuminated.

    OK:
    MIL is not illuminated.

  1. Reconnect the ECM connector.



NG
Go to step 4
OK

REPLACE ECM (Click here)

4. CHECK HARNESS AND CONNECTOR (COMBINATION METER - ECM)

  1. A163122E07
    Disconnect the ECM connector.

  1. Disconnect the combination meter connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    D32-30 (W) - E1-10
    Always
    Bellow 1 Ω

    Standard resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    D32-30 (W) or E1-10 - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the ECM connector.

  1. Reconnect the combination meter connector.



NG
CHECK HARNESS AND CONNECTOR (COMBINATION METER - ECM)
OK

REPLACE COMBINATION METER ASSEMBLY (Click here)

5. CHECK THAT ENGINE STARTS
  1. Turn the ignition switch on (IG).

  1. Start the engine.

    Result:
    Result
    Proceed to
    Engine starts
    A
    Engine does not start*
    B

    HINT:
    *: The intelligent tester cannot communicate with the ECM.



B
GO TO VC OUTPUT CIRCUIT (Click here)
A


6. CHECK HARNESS AND CONNECTOR (COMBINATION METER - BODY GROUND)

  1. A163321E07
    Disconnect the ECM connector.

  1. Turn the ignition switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    D32-30 (W) - Body ground
    Ignition switch on (IG)
    11 to 14 V

  1. Reconnect the ECM connector.



NG
Go to step 7
OK

REPLACE ECM (Click here)

7. CHECK HARNESS AND CONNECTOR (COMBINATION METER - ECM)

  1. A163122E07
    Disconnect the ECM connector.

  1. Disconnect the combination meter connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for short):
    Tester Connection
    Condition
    Specified Condition
    D32-30 (W) - E1-10
    Always
    Bellow 1 Ω

    Standard resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    D32-30 (W) or E1-10 - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the ECM connector.

  1. Reconnect the combination meter connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (COMBINATION METER - ECM)
OK

REPLACE COMBINATION METER ASSEMBLY (Click here)


← Brake Override System (from Jul 2010)MIL Circuit (Aug 2008 – Jun 2010) →