DATA LIST / ACTIVE TEST
System information · Vehicles built Aug 2008 – Jun 2010
Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010
| DATA LIST |
- HINT:
- Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
- NOTICE:
- In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Warm up the engine.
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Chassis / ABS/VSC/TRC / Data List.
According to the display on the tester, read the Data List.
(*1): for 4WDABS / VSC / TRC: Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
ABS Warning Light
ABS warning light / ON or OFF
ON: Warning light ON
OFF: Warning light OFF
-
Brake Warning Light
Brake warning light / ON or OFF
ON: Warning light ON
OFF: Warning light OFF
-
Slip Indicator Light
Slip indicator light / ON or OFF
ON: Indicator light ON
OFF: Indicator light OFF
-
Downhill Assist Control Light (*1)
Downhill assist control indicator light / ON or OFF
ON: Indicator light ON
OFF: Indicator light OFF
-
Buzzer
Skid control buzzer / ON or OFF
ON: Buzzer ON
OFF: Buzzer OFF
-
Stop Light SW
Stop light switch / ON or OFF
ON: Brake pedal depressed
OFF: Brake pedal released
-
Parking Brake SW
Parking brake switch / ON or OFF
ON: Parking brake applied
OFF: Parking brake released
-
Main Idle SW
Main idle switch / ON or OFF
ON: Accelerator pedal released
OFF: Accelerator pedal depressed
-
Brake Pedal Load Sensing SW
Brake pedal load sensing switch / ON or OFF
ON: Brake pedal depressed beyond the specified point
OFF: Brake pedal not depressed beyond the specified point
-
Gear Position
Gear position information / P/N, R, 1st-8th, FAIL, NOT R
Actual gear position
-
Shift Lever Position
Shift lever position information / P/N, R, D/M, 1st-6th/B, FAIL
Actual shift lever position
-
Shift Information
Shift information / ON or OFF
ON: During gear change
-
Inspection Mode
Inspection mode / OTHER or INSPECT
OTHER: Normal mode
INSPECT: Inspection mode
-
Number of IG ON (Inspection)
Number of ignition switch being turned on (IG) after entering inspection mode / min.: 0, max.: 255
Min.: 0
Max.: 255
-
Downhill Assist Control Switch (*1)
Downhill assist control switch / ON or OFF
ON: Switch ON
OFF: Switch OFF
-
Master Cylinder Sensor
Master cylinder pressure sensor / min.: 0 V, max.: 5 V
When brake pedal is released: 0.3 to 0.9 V
Reading increases when brake pedal is depressed
Zero Point of M/C
Memorized zero value / min.: -12.5 MPa, max.: 12.4 MPa
Min.: -12.5 MPa
Max.: 12.4 MPa
-
Deceleration Sensor
Acceleration sensor / min.: -18.52 m/s2, max.: 18.39 m/s2
Min.: -18.52 m/s2
Max.: 18.39 m/s2
Reading changes when vehicle is bounced
Zero Point of Decele
Memorized zero value / min.: -25.11 m/s2, max.: 24.91 m/s2
Min.: -25.11 m/s2
Max.: 24.91 m/s2
-
Deceleration Sensor 2
Acceleration sensor 2 / min.: -18.52 m/s2, max.: 18.39 m/s2
Min.: -18.52 m/s2
Max.: 18.39 m/s2
Reading changes when vehicle is bounced
Zero Point of Decele 2
Memorized zero value / min.: -25.11 m/s2, max.: 24.91 m/s2
Min.: -25.11 m/s2
Max.: 24.91 m/s2
-
Yaw Rate Sensor
Yaw rate sensor / min.: -128 deg/s, max.: 127 deg/s
Vehicle stationary: 0 deg/s
Right turn: -128 to 0 deg/s
Left turn: 0 to 127 deg/s
-
Zero Point of Yaw Rate
Memorized zero value / min.: -128 deg/s, max.: 127 deg/s
Min.: -128 deg/s
Max.: 127 deg/s
-
Yaw Rate Sensor 2
Yaw rate sensor 2 / min.: -128 deg/s, max.: 127 deg/s
Vehicle stationary: 0 deg/s
Right turn: -128 to 0 deg/s
Left turn: 0 to 127 deg/s
-
Zero Point of Yaw Rate 2
Memorized zero value / min.: -128 deg/s, max.: 127 deg/s
Min.: -128 deg/s
Max.: 127 deg/s
-
Steering Angle Sensor
Steering angle sensor / min.: -3276.8 deg, max.: 3276.7 deg
Left turn: Increase
Right turn: Decrease
-
Zero Point of Steering Angle
Memorized zero value / min.: -3276.8 deg, max.: 3276.7 deg
Min.: -3276.8 deg
Max.: 3276.7 deg
-
Lateral G
Lateral G / min.: -25.11 m/s2, max.: 24.91 m/s2
Min.: -25.11 m/s2
Max.: 24.91 m/s2
-
Forward and Rearward G
Forward and backward G / min.: -25.11 m/s2, max.: 24.91 m/s2
Min.: -25.11 m/s2
Max.: 24.91 m/s2
-
Yaw Rate Value
Yaw rate value / min.: -128 deg/s, max.: 127 deg/s
Min.: -128 deg/s
Max.: 127 deg/s
-
Steering Angle Value
Steering angle value / min.: -3276.8 deg, max.: 3276.7 deg
Min.: -3276.8 deg
Max.: 3276.7 deg
-
Stop Light Relay (*2)
Stop light control relay / ON or OFF
ON: Relay ON
OFF: Relay OFF
-
FR Wheel Speed
FR wheel speed sensor reading / min.: 0 km/h (0 mph), max.: 326 km/h (202 mph)
Actual wheel speed
Similar speed as indicated on speedometer
FL Wheel Speed
FL wheel speed sensor reading / min.: 0 km/h (0 mph), max.: 326 km/h (202 mph)
Actual wheel speed
Similar speed as indicated on speedometer
RR Wheel Speed
RR wheel speed sensor reading / min.: 0 km/h (0 mph), max.: 326 km/h (202 mph)
Actual wheel speed
Similar speed as indicated on speedometer
RL Wheel Speed
RL wheel speed sensor reading / min.: 0 km/h (0 mph), max.: 326 km/h (202 mph)
Actual wheel speed
Similar speed as indicated on speedometer
Vehicle Speed
Maximum wheel speed sensor reading / min.: 0 km/h (0 mph), max.: 326 km/h (202 mph)
Actual vehicle speed
Speed indicated on speedometer
FR Wheel Acceleration
FR wheel acceleration / min.: -200.84 m/s2, max.: 199.27 m/s2
0 m/s2
-
FL Wheel Acceleration
FL wheel acceleration / min.: -200.84 m/s2, max.: 199.27 m/s2
0 m/s2
-
RR Wheel Acceleration
RR wheel acceleration / min.: -200.84 m/s2, max.: 199.27 m/s2
0 m/s2
-
RL Wheel Acceleration
RL wheel acceleration / min.: -200.84 m/s2, max.: 199.27 m/s2
0 m/s2
-
Stop Light Relay Output (*2)
Stop light control relay output / ON or OFF
ON: Relay output ON
OFF: Relay output OFF
-
FR Wheel ABS Ctrl Status
FR wheel ABS control status / ON or OFF
ON: During control
-
FL Wheel ABS Ctrl Status
FL wheel ABS control status / ON or OFF
ON: During control
-
RR Wheel ABS Ctrl Status
RR wheel ABS control status / ON or OFF
ON: During control
-
RL Wheel ABS Ctrl Status
RL wheel ABS control status / ON or OFF
ON: During control
-
RR Wheel EBD Ctrl Status
RR wheel EBD control status / ON or OFF
ON: During control
-
RL Wheel EBD Ctrl Status
RL wheel EBD control status / ON or OFF
ON: During control
-
BA Ctrl Status
BA control status / ON or OFF
ON: During control
-
TRC (TRAC) Ctrl Status
TRC control status / ON or OFF
ON: During control
-
TRC (TRAC) Engine Ctrl Status
TRC engine control status / ON or OFF
ON: During control
-
TRC (TRAC) Brake Ctrl Status
TRC brake control status / ON or OFF
ON: During control
-
FR Wheel VSC Ctrl Status
FR wheel VSC control status / ON or OFF
ON: During control
-
FL Wheel VSC Ctrl Status
FL wheel VSC control status / ON or OFF
ON: During control
-
RR Wheel VSC Ctrl Status
RR wheel VSC control status / ON or OFF
ON: During control
-
RL Wheel VSC Ctrl Status
RL wheel VSC control status / ON or OFF
ON: During control
-
Engine Revolutions
Engine revolutions / min.: 0 r/min, max.: 65535 r/min
Min..: 0 r/min
Max.: 65535 r/min
-
Real Engine Torque
Real engine torque / min.: -1024 N*m, max.: 1023 N*m
Min.: -1024 N*m
Max.: 1023 N*m
-
Accelerator Opening Angle %
The difference of a present accelerator / min.: 0 %, max.: 128 %
Min.: 0 %
Max.: 128 %
-
Solenoid Relay
ABS solenoid relay / ON or OFF
ON: Solenoid relay ON
OFF: Solenoid relay OFF
-
ABS Motor Relay
ABS motor relay / ON or OFF
ON: Motor relay ON
OFF: Motor relay OFF
-
Fail Safe Motor Relay
ABS motor fail safe relay / ON or OFF
ON: Motor relay ON
OFF: Motor relay OFF
-
TR(A)C/VSC Solenoid (SM2)
Master cut solenoid (SM2) / ON or OFF
ON: Operates
-
TR(A)C/VSC Solenoid (SM1)
Master cut solenoid (SM1) / ON or OFF
ON: Operates
-
ABS Solenoid (SFRH)
ABS solenoid (SFRH) / ON or OFF
ON: Operates
-
ABS Solenoid (SFRR)
ABS solenoid (SFRR) / ON or OFF
ON: Operates
-
ABS Solenoid (SFLH)
ABS solenoid (SFLH) / ON or OFF
ON: Operates
-
ABS Solenoid (SFLR)
ABS solenoid (SFLR) / ON or OFF
ON: Operates
-
ABS Solenoid (SRRH)
ABS solenoid (SRRH) / ON or OFF
ON: Operates
-
ABS Solenoid (SRRR)
ABS solenoid (SRRR) / ON or OFF
ON: Operates
-
ABS Solenoid (SRLH)
ABS solenoid (SRLH) / ON or OFF
ON: Operates
-
ABS Solenoid (SRLR)
ABS solenoid (SRLR) / ON or OFF
ON: Operates
-
FR Speed Open
FR speed sensor open detection / ERROR or NORMAL
ERROR: Momentary interruption
NORMAL: Normal
-
FL Speed Open
FL speed sensor open detection / ERROR or NORMAL
ERROR: Momentary interruption
NORMAL: Normal
-
RR Speed Open
RR speed sensor open detection / ERROR or NORMAL
ERROR: Momentary interruption
NORMAL: Normal
-
RL Speed Open
RL speed sensor open detection / ERROR or NORMAL
ERROR: Momentary interruption
NORMAL: Normal
-
EFI Communication Open
EFI communication open detection / ERROR or NORMAL
ERROR: Momentary interruption
NORMAL: Normal
-
Yaw Rate Open
Yaw rate sensor open detection / ERROR or NORMAL
ERROR: Momentary interruption
NORMAL: Normal
-
Deceleration Open
Acceleration sensor open detection / ERROR or NORMAL
ERROR: Momentary interruption
NORMAL: Normal
-
Steering Open
Steering angle sensor open detection / ERROR or NORMAL
ERROR: Momentary interruption
NORMAL: Normal
-
Master Cylinder Open
Master cylinder pressure sensor open detection / ERROR or NORMAL
ERROR: Momentary interruption
NORMAL: Normal
-
MT Voltage Value
Motor driving monitor voltage / min.: 0 V, max.: 255 V
Min.: 0 V
Max.: 255 V
-
TRC/VSC Off Mode
VSC OFF switch / NORMAL, TRC OFF or VSC OFF
NORMAL: Normal mode
TRC OFF: TRC off mode
VSC OFF: VSC off mode
-
Number of DTC
Number of DTC recorded / min.: 0, max.: 255
Min.: 0
Max.: 255
-
IG Voltage Value Decreased
IG voltage value decrease detection / ERROR or NORMAL
ERROR: Decrease
NORMAL: Normal
-
IG Voltage Value Increased
IG voltage value increase detection / ERROR or NORMAL
ERROR: Increase
NORMAL: Normal
-
FR Speed Sensor Voltage Open
FR speed sensor voltage open detection / ERROR or NORMAL
ERROR: Momentary interruption
NORMAL: Normal
-
FL Speed Sensor Voltage Open
FL speed sensor voltage open detection / ERROR or NORMAL
ERROR: Momentary interruption
NORMAL: Normal
-
RR Speed Sensor Voltage Open
RR speed sensor voltage open detection / ERROR or NORMAL
ERROR: Momentary interruption
NORMAL: Normal
-
RL Speed Sensor Voltage Open
RL speed sensor voltage open detection / ERROR or NORMAL
ERROR: Momentary interruption
NORMAL: Normal
-
M/C Pressure Sensor Noise
Master cylinder pressure sensor noise detection / ERROR or NORMAL
ERROR: Malfunction
NORMAL: Normal
-
Brake Pedal Switch Open
Brake pedal load sensing switch open detection / ERROR or NORMAL
ERROR: Momentary interruption
NORMAL: Normal
-
Yaw Rate Sensor Voltage Open
Yaw rate sensor voltage open detection / ERROR or NORMAL
ERROR: Momentary interruption
NORMAL: Normal
-
EFI Communication Invalid
EFI communication invalid detection / ERROR or NORMAL
ERROR: Invalid
NORMAL: Normal
-
(*2): with downhill assist control (for 4WD) or hill-start assist control
| ACTIVE TEST |
- HINT:
- Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts to operate without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
Warm up the engine.
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Turn the ignition switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Chassis / ABS/VSC/TRC / Active Test.
According to the display on the tester, perform the Active Test.
(*1): for 4WDABS / VSC / TRC: Tester Display
Test Part
Control Range
Diagnostic Note
ABS Warning Light
ABS warning light
Warning light ON / OFF
Observe combination meter
Brake Warning Light
Brake warning light
Warning light ON / OFF
Observe combination meter
Slip Indicator Light
Slip indicator light
Indicator light ON / OFF
Observe combination meter
VSC OFF Indicator Light
VSC OFF indicator light
Indicator light ON / OFF
Observe combination meter
TRC OFF Indicator Light
TRC OFF indicator light
Indicator light ON / OFF
Observe combination meter
Downhill Assist Control Light (*1)
Downhill assist control indicator light
Indicator light ON / OFF
Observe combination meter
Buzzer
Skid control buzzer
Buzzer ON / OFF
Buzzer can be heard
Solenoid Relay
ABS solenoid relay
Relay ON / OFF
-
Motor Relay
ABS motor relay
Relay ON / OFF
Operating sound of motor can be heard
Stop Light Relay (*2)
Stop light control relay
Relay ON / OFF
Stop lights come on
ABS Solenoid (SRLR)
ABS solenoid (SRLR)
Solenoid ON / OFF
Operating sound of solenoid (clicking sound) can be heard
ABS Solenoid (SRLH)
ABS solenoid (SRLH)
Solenoid ON / OFF
Operating sound of solenoid (clicking sound) can be heard
ABS Solenoid (SRRR)
ABS solenoid (SRRR)
Solenoid ON / OFF
Operating sound of solenoid (clicking sound) can be heard
ABS Solenoid (SRRH)
ABS solenoid (SRRH)
Solenoid ON / OFF
Operating sound of solenoid (clicking sound) can be heard
ABS Solenoid (SFLR)
ABS solenoid (SFLR)
Solenoid ON / OFF
Operating sound of solenoid (clicking sound) can be heard
ABS Solenoid (SFLH)
ABS solenoid (SFLH)
Solenoid ON / OFF
Operating sound of solenoid (clicking sound) can be heard
ABS Solenoid (SFRR)
ABS solenoid (SFRR)
Solenoid ON / OFF
Operating sound of solenoid (clicking sound) can be heard
ABS Solenoid (SFRH)
ABS solenoid (SFRH)
Solenoid ON / OFF
Operating sound of solenoid (clicking sound) can be heard
VSC/TRC Solenoid (SMR)
Master cut solenoid (SM2)
Solenoid ON / OFF
Operating sound of solenoid (clicking sound) can be heard
VSC/TRC Solenoid (SMF)
Master cut solenoid (SM1)
Solenoid ON / OFF
Operating sound of solenoid (clicking sound) can be heard
(*2): with downhill assist control (for 4WD) or hill-start assist control