2007-2013 Highlander Kluger · Service Manual ENGINE

TERMINALS OF ECU

System information · Vehicles built from Jul 2010

Versions by build date: May 2007 – Jun 2010 from Jul 2010


CHECK MAIN BODY ECU (INSTRUMENT PANEL JUNCTION BLOCK)
B112605E15
  1. Disconnect the D6, D7, D8, 1E, 1F and 1M connectors.

  2. Measure the voltage and resistance of the wire harness side connector.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    D7-6 (AM1) - Body ground
    GR - Body ground
    +B power supply
    Always
    11 to 14 V
    D6-1 (AM2) - Body ground
    G - Body ground
    +B power supply
    Always
    11 to 14 V
    D7-16 (SSW2) - Body ground
    L - Body ground
    Engine switch signal
    Engine switch pushed
    Below 1 Ω
    D7-16 (SSW2) - Body ground
    L - Body ground
    Engine switch signal
    Engine switch not pushed
    10 kΩ or higher
    D7-17 (SSW1) - Body ground
    P - Body ground
    Engine switch signal
    Engine switch pushed
    Below 1 Ω
    D7-17 (SSW1) - Body ground
    P - Body ground
    Engine switch signal
    Engine switch not pushed
    10 kΩ or higher
    1M-9 (GND2) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    D8-5 (CANH) - Body ground
    GR - Body ground
    CAN Line
    Always
    10 kΩ or higher
    D8-6 (CANL) - Body ground
    W - Body ground
    CAN Line
    Always
    10 kΩ or higher
    D8-15 (CANN) - Body ground
    W - Body ground
    CAN Line
    Always
    10 kΩ or higher
    D8-16 (CANP) - Body ground
    Y - Body ground
    CAN Line
    Always
    10 kΩ or higher
    1F-10 (GND1) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    1E-7 (LIN1) - Body ground
    R - Body ground
    LIN line
    Always
    10 kΩ or higher
    If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the connectors.

  4. Measure the voltage of the connector.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    D6-3 (ACCR) - 1M-9 (GND2)
    BE - W-B
    Starter assist signal
    (ACC cut signal)
    Brake pedal depressed, shift lever P position, engine switch is pushed once → on (IG)
    0.1 to 0.8 V *1
    → Output voltage at terminal AM1 or AM2 is -2 V or more.
    D6-11 (IG2D) - 1M-9 (GND2)
    Y - W-B
    IG2 signal
    Engine switch on (IG)
    Output voltage at terminal AM1 or AM2 is -2 V or more.
    D6-11 (IG2D) - 1M-9 (GND2)
    Y - W-B
    IG2 signal
    Engine switch on (ACC)
    Below 1 V
    D7-3 (IG1D) - 1M-9 (GND2)
    SB - W-B
    IG1 signal
    Engine switch on (IG)
    Output voltage at terminal AM1 or AM2 is -2 V or more.
    D7-3 (IG1D) - 1M-9 (GND2)
    SB - W-B
    IG1 signal
    Engine switch on (ACC)
    Below 1 V
    D7-8 (STR) - 1M-9 (GND2)
    B - W-B
    Park/Neutral position switch signal
    Engine switch on (IG), shift lever except P or N position → P or N position
    Below 2 V → Pulse generation *3
    D7-18 (SLP) - 1M-9 (GND2)
    BE - W-B
    Steering lock actuator position signal
    Steering lock is locked
    Pulse generation
    (See waveform 3)
    D7-18 (SLP) - 1M-9 (GND2)
    BE - W-B
    Steering lock actuator position signal
    Steering lock is released
    Pulse generation
    (See waveform 3)
    D7-19 (SLR+) - 1M-9 (GND2)
    Y - W-B
    Steering lock motor signal
    Steering lock motor operating
    Below 1 V
    D7-19 (SLR+) - 1M-9 (GND2)
    Y - W-B
    Steering lock motor signal
    Steering lock motor does not operate
    Output voltage at terminal AM1 or AM2 is -2 V or more.
    D7-22 (ACCD) - 1M-9 (GND2)
    GR - W-B
    ACC signal
    Engine switch on (ACC)
    Output voltage at terminal AM1 or AM2 is -2 V or more.
    D7-22 (ACCD) - 1M-9 (GND2)
    GR - W-B
    ACC signal
    Engine switch off
    Below 1 V
    D7-25 (SWIL) - 1M-9 (GND2)
    R - W-B
    Illumination signal
    Light control switch TAIL or HEAD
    Output voltage at terminal AM1 or AM2 is -2 V or more.
    D8-8 (TACH) - 1M-9 (GND2)
    V - W-B
    Tachometer signal
    Engine running
    Pulse generation
    (See waveform 2)
    D8-9 (SPD) - 1M-9 (GND2)
    R - W-B
    Vehicle speed signal
    Engine switch on (IG), rotate rear wheel slowly
    Pulse generation
    (See waveform 1)
    D9-4 (STSW) - 1M-9 (GND2)
    P - W-B
    Starter activation request signal
    Brake pedal depressed, engine switch held on (ST)
    Output voltage at terminal AM1 or AM2 is -2 V or more.
    D9-6 (STR2) - 1M-9 (GND2)
    LG - W-B
    Starter signal (Sub)
    Brake pedal depressed, shift lever P or N position, engine switch on (ST)
    Output voltage at terminal AM1 or AM2 is -3.5 V or more. *2
    1A-1 (IG) - Body ground
    B - Body ground
    IG power supply
    Always
    11 to 14 V
    1C-13 (STP) - 1M-9 (GND2)
    L - W-B
    Stop light signal
    Brake pedal depressed
    Output voltage at terminal AM1 or AM2 is -2 V or more.
    1C-13 (STP) - 1M-9 (GND2)
    L - W-B
    Stop light signal
    Brake pedal released
    Below 1 V

    HINT:
    *1: Voltage is output only when the engine is cranking.
    *2: Voltage is output for 0.3 seconds when the engine is cranking to start. Disconnect the B2 connector from the ECM and starter cut relay before measuring the voltage.
    *3: Remove the starter cut relay before measuring the voltage.

    If the result is not as specified, the ECU may have a malfunction.

  5. Using an oscilloscope, check the signal waveform of the ECU.

    1. I042329E01
      Waveform 1
      Waveform 1 (Reference): 
      Terminal No.
      D8-9 (SPD) - 1M-9 (GND2)
      Tool Setting
      5 V/DIV., 10 ms./DIV.
      Vehicle Condition
      Driving at approx. 20 km/h (12 mph)

      HINT:
      As the vehicle speed increases, the wavelength shortens.

    2. I042330E01
      Waveform 2
      Waveform 2 (Reference): 
      Terminal No.
      D8-8 (TACH) - 1M-9 (GND2)
      Tool Setting
      5 V/DIV., 10 ms./DIV.
      Vehicle Condition
      Engine idling

      HINT:
      As the engine revolution speed increases, the wavelength shortens.

    3. A130277E01
      Waveform 3
      Waveform 3 (Reference): 
      Terminal No.
      D7-18 (SLP) - 1M-9 (GND2)
      Tool Setting
      2 V/DIV., 100 ms./DIV.
      Vehicle Condition
      Steering lock/unlock


CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
B122343E30
  1. Disconnect the D36 ECU connector.

  2. Measure the voltage and resistance of the wire harness side connector.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    D36-1 (+B) - Body ground
    B - Body ground
    +B power supply
    Always
    11 to 14 V
    D36-10 (LIN) - Body ground
    L - Body ground
    LIN line
    Always
    10 kΩ or higher
    D36-17 (E) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the ECU connector.

  4. Measure the voltage of the connector.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    D36-18 (IG) - Body ground
    G - Body ground
    Ignition power supply
    Engine switch on (IG)
    11 to 14 V
    D36-18 (IG) - Body ground
    G - Body ground
    Ignition power supply
    Engine switch off
    Below 1 V
    If the result is not as specified, the ECU may have a malfunction.


CHECK ECM
A206553E10
  1. Disconnect the B47, B48, D55 and D56 ECM connectors.

  2. Measure the voltage and resistance of the wire harness side connectors.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    D56-23 (+B2) - Body ground
    GR - Body ground
    Power source of ECM
    Engine switch on (IG)
    11 to 14 V
    D56-22 (+B) - Body ground
    SB - Body ground
    Power source of ECM
    Engine switch on (IG)
    11 to 14 V
    D55-21 (IGSW) - Body ground
    W - Body ground
    Engine switch signal
    Engine switch on (IG)
    11 to 14 V
    B47-10 (ME01) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    B47-15 (E02) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    B47-14 (E01) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    B47-16 (E04) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    B47-18 (E05) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    B48-12 (E1) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    B47-11 (E03) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the ECM connectors.

  4. Measure the voltage of the connectors.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    D55-13 (ACCR) - B48-12 (E1)
    BE - W-B
    ACC relay cut signal (output)
    Brake pedal depressed, shift lever P or N position, engine switch is pushed once → on (IG)
    0.1 to 0.8 V *1 → Output voltage at terminal AM1 or AM2 is -2 V or more.
    D55-30 (STSW) - B48-12 (E1)
    P - W-B
    Starter activation request signal
    Brake pedal depressed, engine switch held (IG)
    Output voltage at terminal AM1 or AM2 is -2 V or more.
    D55-29 (TACH) - B48-12 (E1)
    B - W-B
    Engine revolution signal (output)
    Idling
    Pulse generation (see waveform 1)
    D55-18 (STP) - B48-12 (E1)
    R - W-B
    Stop light switch signal (input)
    Brake pedal depressed
    7.5 to 14 V
    D55-18 (STP) - B48-12 (E1)
    R - W-B
    Stop light switch signal (input)
    Brake pedal released
    Below 1.5 V
    D55-10 (STA) - B48-12 (E1)
    B - W-B
    Starter relay operation signal
    Cranking
    11 to 14 V
    B48-31 (STAR) - B48-12 (E1)
    GR - W-B
    Starter signal (Main)
    Brake pedal depressed, shift lever P or N position, engine switch on (ST)
    11 to 14 V

    HINT:
    *1: Voltage is output only when the engine is cranking.

    If the result is not as specified, the ECM may have a malfunction.

  5. I042330E01
    Using an oscilloscope, check the signal waveform of the ECM.
    Waveform 1 (Reference): 
    Terminal No.
    D55-29 (TACH) - B48-12 (E1)
    Tool Setting
    5 V/DIV., 10 ms./DIV.
    Vehicle Condition
    Engine idling

    HINT:
    As the vehicle speed increases, the wavelength shortens.


CHECK STEERING LOCK ECU
B118684E13
  1. Disconnect the D10 ECU connector.

  2. Measure the voltage and resistance of the wire harness side connector.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    D10-1 (GND) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    D10-2 (SGND) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    D10-6 (IG2) - Body ground
    V - Body ground
    Ignition power supply
    Engine switch on (IG)
    11 to 14 V
    D10-6 (IG2) - Body ground
    V - Body ground
    Ignition power supply
    Engine switch off
    Below 1 V
    D10-7 (B) - Body ground
    G - Body ground
    +B power supply
    Always
    11 to 14 V
    1. If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the D10 ECU connector.

  4. Measure the voltage of the connector.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    D10-4 (SLP1) - D10-1 (GND)
    BE - W-B
    Steering lock actuator position signal
    Steering is locked
    11 to 14 V
    D10-4 (SLP1) - D10-1 (GND)
    BE - W-B
    Steering lock actuator position signal
    Steering is released
    Below 1 V
    1. If the result is not as specified, the ECU may have a malfunction.

← TERMINALS OF ECU (May 2007 – Jun 2010)DIAGNOSIS SYSTEM (from May 2007) →