2007-2013 Highlander Kluger · Service Manual BRAKE

C1425 Open in Stop Light Switch Circuit

Diagnostic trouble codes · Vehicles built May 2007 – Jul 2008

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010

DESCRIPTION

The skid control ECU (housed in the actuator assembly) inputs stop light switch signals and the condition of brake operation.
The skid control ECU has an open detection circuit, which outputs this DTC when detecting an open in the stop light input line or the ground line of the stop light circuit with the stop light switch off (brake pedal not depressed).
DTC Code
DTC Detection Condition
Trouble Area
C1425
When IG1 terminal voltage is between 9.5 and 17.4 V, an open stop light switch circuit continues for 3 seconds or more.
  1. STOP fuse
  2. Stop light switch
  3. Stop light switch circuit
  4. Stop light control relay
  5. Stop light control relay circuit
  6. Brake actuator assembly (Skid control ECU)

WIRING DIAGRAM

C171154E01
C168442E02

INSPECTION PROCEDURE

NOTICE:
When replacing the brake actuator assembly, perform zero point calibration (Click here).


1. CHECK STOP LIGHT OPERATION
  1. Check that the stop lights come on when the brake pedal is depressed, and go off when the brake pedal is released.

    OK:
    Condition
    Illumination Condition
    Brake pedal depressed
    ON
    Brake pedal released
    OFF



NG
Go to step 4
OK


2. READ VALUE ON INTELLIGENT TESTER (STOP LIGHT SWITCH)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch on (IG).

  1. Select the Data List mode on the intelligent tester (Click here).

    ABS / VSC / TRC: 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Stop Lamp SW
    Stop light switch / ON or OFF
    ON: Brake pedal depressed
    OFF: Brake pedal released
    -

  1. Check that the stop light switch display observed on the intelligent tester changes according to brake pedal operation.

    OK:
    The intelligent tester displays ON or OFF according to brake pedal operation.



NG
Go to step 11
OK


3. RECONFIRM DTC
  1. Turn the ignition switch off.

  1. Clear the DTCs (Click here).

  1. Start the engine.

  1. Depress the brake pedal several times to test the stop light circuit.

  1. Check if the same DTC is recorded (Click here).

    Result:
    Result
    Proceed to
    DTC (C1425) is not output
    A
    DTC (C1425) is output
    B

    HINT:
    If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step (Click here).



B
REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)
A

CHECK FOR INTERMITTENT PROBLEMS (SYMPTOM SIMULATION) (Click here)

4. INSPECT STOP FUSE

  1. C156506E02
    Remove the STOP fuse from the main body ECU (instrument panel junction block).

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    STOP (10 A) fuse
    Always
    Below 1 Ω



NG
REPLACE STOP FUSE
OK


5. INSPECT STOP LIGHT SWITCH (POWER SOURCE TERMINAL)

  1. C142000E13
    Install the STOP fuse.

  1. Make sure that there is no looseness at the locking part and the connecting part of the connectors.

  1. Disconnect the stop light switch connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    A20-2 - Body ground
    Always
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)
OK


6. INSPECT STOP LIGHT SWITCH

  1. C147842E03
    Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 - 2
    Switch pin free
    Below 1 Ω
    1 - 2
    Switch pin pushed in
    10 kΩ or higher



NG
REPLACE STOP LIGHT SWITCH (Click here)
OK


7. INSPECT STOP LIGHT CONTROL RELAY

  1. C126459E06
    Remove the stop light control relay.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    3 - 4
    Voltage is not applied between terminals 1 and 2
    Below 1 Ω



NG
REPLACE STOP LIGHT CONTROL RELAY
OK


8. CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH - ENGINE ROOM RELAY BLOCK)

  1. C168479E02
    Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A20-1 - Stop light control relay terminal 4
    Always
    Below 1 Ω
    A20-1 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


9. CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - ENGINE ROOM RELAY BLOCK)

  1. C168480E01
    Make sure that there is no looseness at the locking part and the connecting part of the connectors.

  1. Disconnect the skid control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A24-2 (STP) - Stop light control relay terminal 3
    Always
    Below 1 Ω
    A24-2 (STP) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


10. RECONFIRM DTC
  1. Clear the DTCs (Click here).

  1. Start the engine.

  1. Depress the brake pedal several times to test the stop light circuit.

  1. Check if the same DTC is recorded (Click here).

    HINT:
    Reinstall the relay, connectors, etc. and restore the vehicle to its prior condition before rechecking for DTCs.


    Result:
    Result
    Proceed to
    DTC (C1425) is not output
    A
    DTC (C1425) is output
    B

    HINT:
    If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step (Click here).



B
REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)
A

INSPECT LIGHTING SYSTEM (STOP LIGHT CIRCUIT) (Click here)

11. CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - ENGINE ROOM RELAY BLOCK)

  1. C168480E01
    Turn the ignition switch off.

  1. Remove the stop light control relay.

  1. Make sure that there is no looseness at the locking part and the connecting part of the connectors.

  1. Disconnect the skid control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A24-2 (STP) - Stop light control relay terminal 3
    Always
    Below 1 Ω
    A24-2 (STP) - Body ground
    Always
    10 kΩ or higher

    HINT:
    If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step (Click here).



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)


← C1422 Master Cylinder Pressure Sensor Zero Point High Malfunction (from Jul 2010)C1425 Open in Stop Light Switch Circuit (Aug 2008 – Jun 2010) →