2007-2013 Highlander Kluger · Service Manual BRAKE

C1427 Motor Malfunction

Diagnostic trouble codes · Vehicles built May 2007 – Jul 2008

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010

DESCRIPTION

DTC Code
DTC Detection Condition
Trouble Area
C1427
Actuator pump motor does not operate properly.
  1. Brake actuator assembly (Ground circuit)
  2. Brake actuator assembly (Motor circuit)

WIRING DIAGRAM

Refer to DTCs C0273, C0274 and C1361 (Click here).

INSPECTION PROCEDURE

NOTICE:
When replacing the brake actuator assembly, perform zero point calibration (Click here).


1. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (ABS MOTOR RELAY)
  1. Connect the intelligent tester to the DLC3.

  1. Start the engine.

  1. Select the Active Test mode on the intelligent tester (Click here).

    ABS / VSC / TRC: 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Motor Relay
    ABS motor relay
    Relay ON / OFF
    Operating sound of motor can be heard

  1. Check for operating sound of the ABS motor relay when operating it with the intelligent tester.

    Result:
    Result
    Proceed to
    Operating sound is not heard
    A
    Operating sound is heard
    B



B
Go to step 3
A


2. INSPECT SKID CONTROL ECU (GND2 TERMINAL)

  1. C160263E48
    Turn the ignition switch off.

  1. Make sure that there is no looseness at the locking part and the connecting part of the connectors.

  1. Disconnect the skid control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A24-13 (GND2) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (GND2 CIRCUIT)
OK


3. RECONFIRM DTC

HINT:
This code is detected when a problem is identified in the brake actuator assembly.
The ABS motor relay is in the brake actuator assembly.
Therefore, ABS motor relay unit inspection cannot be performed. Be sure to check if the DTC is output before replacing the brake actuator assembly.

  1. Turn the ignition switch off.

  1. Reconnect the skid control ECU connector.

  1. Clear the DTCs (Click here).

  1. Start the engine.

  1. Drive the vehicle at a speed of 20 km/h (12 mph) or more for 30 seconds or more.

  1. Check if the same DTC is recorded (Click here).

    Result:
    Result
    Proceed to
    DTC (C1427) is not output
    A
    DTC (C1427) is output
    B

    HINT:
    1. If a speed signal of 6 km/h (4 mph) or more is input to the skid control ECU with the ignition switch on (IG) and the stop light switch off, the ECU performs self diagnosis of the motor and solenoid circuits.
    2. If the normal system code is output (no trouble codes are output), slightly jiggle the connectors, wire harness, and fuses of the brake actuator assembly. Make sure that no DTCs are output.
    3. If any DTCs are output while jiggling a connector or wire harness of the brake actuator assembly (skid control ECU), inspect and repair the connector or wire harness.
    4. It is suspected that the DTCs were output due to a bad connection of the connector terminal.



B
REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)
A

CHECK FOR INTERMITTENT PROBLEMS (SYMPTOM SIMULATION) (Click here)


← C1426 Stop Light Switch OFF Stuck Malfunction (from Jul 2010)C1427 Motor Malfunction (Aug 2008 – Jun 2010) →