2007-2013 Highlander Kluger · Service Manual BODY ELECTRICAL

CUSTOMIZE PARAMETERS

Troubleshooting · Vehicles built May 2007 – Jun 2010

Versions by build date: May 2007 – Jun 2010 from Jul 2010


CUSTOMIZING FUNCTION WITH INTELLIGENT TESTER

HINT:
The items in the table below can be customized.

NOTICE:
  1. When the customer requests a change in a function, first make sure that the function can be customized.
  2. Be sure to make a note of the current setting before customizing.
  3. When troubleshooting a function, first make sure that the function is set to the default setting.

HINT:
The following functions' default settings are ON. Part of these functions can be customized.

  1. Connect the intelligent tester to the DLC3.

  2. Turn the engine switch on (IG).

  3. Turn the tester on.

  4. Select the setting by referring to the table below.

    Entry & Start (Certification ECU (Smart Key ECU Assembly) (SMART)): 
    Display (Item)
    Default
    Contents
    Setting
    Ignition Available Area
    ALL
    Function to choose the available area for electrical key to start engine and release the steering lock.
    FRONT / ALL
    Park Wait Time
    2.5s
    Function that sets waiting time to permit opening door after door is locked with entry lock function.
    0.5s / 1.5s / 2.5s / 5.0s
    Glass Hatch Open Operation
    ON
    Function to open the glass hatch when the driver has the electrical key and presses glass hatch opener switch.
    ON / OFF
    Back Door Opening Operation
    LONG
    Function to open the back door when the driver has the electrical key and presses back door opener switch.
    LONG / TWICE / OFF
    Smart Key (Certification ECU (Smart Key ECU Assembly) (WARNING)): 
    Display (Item)
    Default
    Contents
    Setting
    Passenger Take Key
    ON
    Function to warn that the electrical key is taken out by passengers (It means that the key is taken out from except the driver's door) when engine is running.
    ON / OFF
    Key Out Range Warning
    ON
    Function to set a warning function for trying to start the engine before key is still out of its range.
    ON / OFF
    Key Low Battery Warning
    ON
    Function to set a warning function for the time when a key battery becomes weak.
    ON / OFF


ENTRY UNLOCK MODE SWITCHING FUNCTION *

HINT:
  1. *: for RHD
  2. The function only changes the entry unlock mode of the smart entry and start system. This function is not for the wireless door lock control.

  1. To change the vehicle to entry unlock mode switching function:

    1. Driver door unlock mode:
      When the driver door's touch sensor is touched, only the driver door unlocks. When another touch sensor is touched, all doors unlock.
    2. All door unlock mode:
      When any touch sensor is touched, all doors unlock.

    1. When the engine switch is off, press the LOCK button and one of the other buttons on the key at the same time for approximately 5 seconds while the key is in the actuation area.

    2. The certification ECU (smart key ECU assembly) receives this signal from the door control receiver and switches the entry unlock mode.

    3. The certification ECU (smart key ECU assembly) sounds the wireless door lock buzzer and the buzzer in the combination meter to inform the user that the mode has been switched.

    4. If the entry unlock mode needs to be switched again, press the LOCK button and one of the other three buttons on the key at the same time for approximately 5 seconds after the LED of the key goes off.

      NOTICE:
      After pressing and holding the switches for 4.5 seconds, wait 5 seconds before performing the same procedure again.

  2. The certification ECU (smart key ECU assembly) receives this signal from the door control receiver and changes the smart entry and start system to the entry unlock mode.

  3. The certification ECU (smart key ECU assembly) sounds the wireless door lock buzzer and the buzzer of the combination meter to inform the user that the mode has been switched.
    B178844E01


ELECTRICAL KEY CANCEL
The electrical key cancel operation disables the following functions:
  1. Entry Unlock/Lock
  2. Entry Back Door Open
  3. Entry Glass Hatch Open
  4. Electrical Key Lock-in Prevention
  5. Warning
  1. The operation procedures are as follows:
    Precondition:
    Engine switch off, driver side door closed and unlocked.

    1. Unlock the driver side door once with the UNLOCK switch of the electrical key.

    2. Open the driver door within 5 seconds.

    3. Unlock the driver side door twice with the UNLOCK switch of the electrical key within 5 seconds.

    4. Repeat open and close the driver door twice within 30 seconds, and open again.
      (Open → Close → Open → Close → Open)

    5. Unlock the driver side door twice with the UNLOCK switch of the electrical key within 5 seconds.

    6. Open and close the driver door within 30 seconds, and open again.
      (Open → Close → Open)

    7. Close the driver door within 5 seconds.
      When electrical key cancel is activated, the wireless door lock buzzer sounds twice.
      To return to the original condition, perform the procedures again. When the original condition is returned, the wireless door lock buzzer sounds once.

← OPERATION CHECK (from Jul 2010)CUSTOMIZE PARAMETERS (from Jul 2010) →