2007-2013 Highlander Kluger · Service Manual BODY ELECTRICAL

Front Passenger Side Door Entry Lock Function does not Operate

Circuit diagnosis · Vehicles built Aug 2008 – Jun 2010

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010

DESCRIPTION

If the front passenger side door entry lock function does not operate but the entry unlock function operates, the communication line between the vehicle and electrical key transmitter is normal. As a faulty part, the entry lock switch circuit (certification ECU (smart key ECU assembly) → passenger side door outside handle (entry lock switch) → passenger side door electrical key oscillator) can be considered.

WIRING DIAGRAM

B164327E14

INSPECTION PROCEDURE

NOTICE:
Before performing the inspection, check that there are no problems related to "CAN COMMUNICATION SYSTEM" and "LIN COMMUNICATION SYSTEM".


1. CHECK POWER DOOR LOCK OPERATION
  1. When the door control switch on the master switch assembly is operated, check that the locked doors unlock (Click here).

    OK:
    Locked doors unlock.



NG
GO TO POWER DOOR LOCK CONTROL SYSTEM (Click here)
OK


2. READ VALUE USING INTELLIGENT TESTER (DOOR LOCK POSITION SWITCH)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / Main Body / Data List.

  1. Read the Data List according to the display on the intelligent tester.

    Main Body (Main Body ECU (Instrument Panel Junction Block)) 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    P-Door Lock Pos SW
    Front passenger side door lock position switch signal/ON or OFF
    ON: Front passenger side door is unlocked
    OFF: Front passenger side door is locked
    -

    OK:
    On the intelligent tester screen, the display changes between ON and OFF as shown in the chart above.


    Result:
    Result
    Proceed to
    OK
    A
    NG
    B
    (Proceed to "Front Passenger Door LOCK/UNLOCK Functions do not Operate")



B
GO TO POWER DOOR LOCK CONTROL SYSTEM (Click here)
A


3. READ VALUE ON INTELLIGENT TESTER (DOOR OUTSIDE HANDLE)
  1. Select P Trigger SW in the Data List and read the tester display.

    Entry & Start (Certification ECU (Smart Key ECU Assembly)): 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    P Trigger SW
    Front passenger side door lock switch / ON or OFF
    ON: Entry lock switch is pressed
    OFF: Entry lock switch is not pressed
    -

    OK:
    On the tester screen, the item changes between ON and OFF according to the chart above.



NG
Go to step 4
OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

4. CHECK HARNESS AND CONNECTOR (FRONT DOOR OUTSIDE HANDLE - DOOR ELECTRICAL KEY OSCILLATOR)

  1. B164339E34
    Remove the front door outside handle (Click here).

  1. Disconnect the door electrical key oscillator connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    for LHD:
    Tester Connection
    Condition
    Specified Condition
    z15-1 (TRG-) - z16-9 (TRG-)
    Always
    Below 1 Ω
    z15-1 (TRG-) - Body ground
    Always
    10 kΩ or higher
    for RHD:
    Tester Connection
    Condition
    Specified Condition
    z13-1 (TRG-) - z14-9 (TRG-)
    Always
    Below 1 Ω
    z13-1 (TRG-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5. CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU - FRONT DOOR OUTSIDE HANDLE)

  1. B171408E04
    Disconnect the certification ECU (smart key ECU assembly) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    for LHD:
    Tester Connection
    Condition
    Specified Condition
    D36-4 (TSW2) - z15-3 (TRG+)
    Always
    Below 1 Ω
    D36-4 (TSW2) - Body ground
    Always
    10 kΩ or higher
    for RHD:
    Tester Connection
    Condition
    Specified Condition
    D36-4 (TSW2) - z13-3 (TRG+)
    Always
    Below 1 Ω
    D36-4 (TSW2) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6. INSPECT FRONT DOOR OUTSIDE HANDLE (FRONT PASSENGER SIDE)

  1. B112465E33
    Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    for LHD:
    Tester Connection
    Condition
    Specified Condition
    z15-1 (TRG-) - z15-3 (TRG+)
    Lock switch not pushed
    10 kΩ or higher
    z15-1 (TRG-) - z15-3 (TRG+)
    Lock switch pushed
    Below 1 Ω
    for RHD:
    Tester Connection
    Condition
    Specified Condition
    z13-1 (TRG-) - z13-3 (TRG+)
    Lock switch not pushed
    10 kΩ or higher
    z13-1 (TRG-) - z13-3 (TRG+)
    Lock switch pushed
    Below 1 Ω



NG
REPLACE FRONT DOOR OUTSIDE HANDLE (Click here)
OK


7. REPLACE DOOR ELECTRICAL KEY OSCILLATOR
  1. Replace the door electrical key oscillator (Click here).


NEXT


8. CHECK DOOR ELECTRICAL KEY OSCILLATOR (OPERATION)
  1. Check that the entry functions operate normally.

    OK:
    Entry functions operate normally.



NG
REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
OK

END (DOOR ELECTRICAL KEY OSCILLATOR IS DEFECTIVE)


← Front Passenger Side Door Entry Lock Function does not Operate (May 2007 – Jul 2008)Front Passenger Side Door Entry Lock Function does not Operate (from Jul 2010) →