2007-2013 Highlander Kluger · Service Manual ENGINE

B2278 Engine Switch Circuit Malfunction

Diagnostic trouble codes · Vehicles built from Jul 2010

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010

DESCRIPTION

This DTC is output if 1) a malfunction is detected between the main body ECU and the engine switch; or 2) either of the switches inside the engine switch is malfunctioning.

HINT:
If the main body ECU is replaced with a new one while the negative (-) battery terminal is connected, the power source mode will be in IG-ON mode. When the battery is removed and reinstalled, the power source mode that was selected when the battery was removed is restored.
After the main body ECU is replaced, perform the registration procedure for the engine immobiliser system.

DTC No.
DTC Detection Condition
Trouble Area
B2278
Communication is abnormal between the main body ECU and engine switch or the engine switch is defective
  1. Engine switch
  2. Main body ECU (Instrument panel junction block)
  3. Wire harness or connector

WIRING DIAGRAM

B177338E03

INSPECTION PROCEDURE


1. READ VALUE USING INTELLIGENT TESTER (START SWITCH)
  1. Connect the intelligent tester to the DLC3.

  1. Check the DATA LIST for proper functioning of the start switch.

    HINT:
    When using the intelligent tester with the engine switch off, turn on and off any of the door courtesy light switches repeatedly at 1.5 second intervals or less until communication between the tester and vehicle starts.

    Body: 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    St SW1
    Start Switch 1 / ON or OFF
    ON: Engine switch is pushed
    OFF: Engine switch is not pushed
    -
    St SW2
    Start Switch 2 / ON or OFF
    ON: Engine switch is pushed
    OFF: Engine switch is not pushed
    -

    OK:
    ON (engine switch is pushed) and OFF (engine switch is not pushed) appear on the screen.



NG
Go to step 2
OK

REPLACE MAIN BODY ECU (INSTRUMENT PANEL JUNCTION BLOCK)

2. INSPECT ENGINE SWITCH

  1. Remove the engine switch (Click here).A109252E01

  1. Disconnect the switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    7 (SS1) - 5 (GND)
    Pushed
    Below 1 Ω
    2 (SS2) - 5 (GND)
    Pushed
    Below 1 Ω
    7 (SS1) - 5 (GND)
    Not pushed
    10 kΩ or higher
    2 (SS2) - 5 (GND)
    Not pushed
    10 kΩ or higher

    HINT:
    This switch is a momentary type switch.



NG
REPLACE ENGINE SWITCH (Click here)
OK


3. CHECK HARNESS AND CONNECTOR (ENGINE SWITCH - MAIN BODY ECU AND BODY GROUND)

  1. Disconnect the D7 ECU connector.B175612E03

  1. Disconnect the D22 switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    D22-7 (SS1) - D7-17 (SSW1)
    Always
    Below 1 Ω
    D22-2 (SS2) - D7-16 (SSW2)
    Always
    Below 1 Ω
    D22-5 (GND) - Body ground
    Always
    Below 1 Ω
    D22-7 (SS1) or D7-17 (SSW1) - Body ground
    Always
    10 kΩ or higher
    D22-2 (SS2) or D7-16 (SSW2) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU (INSTRUMENT PANEL JUNCTION BLOCK)


← B2278 Engine Switch Circuit Malfunction (Aug 2008 – Jun 2010)B2281 "P" Signal Malfunction (May 2007 – Jul 2008) →