2007-2013 Highlander Kluger · Service Manual RESTRAINTS

SRS Warning Light does not Come ON

Circuit diagnosis · Vehicles built May 2007 – Jul 2008

Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010

DESCRIPTION

The SRS warning light is located on the combination meter assembly.
When the SRS is normal, the SRS warning light comes on for approximately 6 seconds after the ignition switch is turned from off to on (IG), and then goes off automatically.
If there is a malfunction in the SRS, the SRS warning light comes on to inform the driver of a problem.
When terminals TC and CG of the DLC3 are connected, the DTC is displayed by blinking of the SRS warning light.
The SRS is equipped with a voltage-increase circuit (DC-DC converter) in the center airbag sensor assembly in case the source voltage drops.
When the battery voltage drops, the voltage-increase circuit (DC-DC converter) functions to increase the voltage of the SRS to the normal voltage.
A malfunction in this circuit is not recorded in the center airbag sensor assembly. The SRS warning light automatically goes off when the source voltage returns to normal.
The signal to illuminate the SRS warning light is transmitted from the center airbag sensor assembly to the combination meter assembly through the CAN communication system.

WIRING DIAGRAM

C170104E01

INSPECTION PROCEDURE


1. CHECK BATTERY VOLTAGE
  1. Measure the voltage of the battery.

    Standard voltage:
    11 to 14 V



NG
INSPECT CHARGING SYSTEM AND BATTERY
OK


2. CHECK CONNECTOR
  1. Turn the ignition switch off.

  1. Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.

  1. Check that the connector is properly connected to the combination meter assembly.

    OK:
    The connector is properly connected.

    HINT:
    If the connector is not connected securely, reconnect the connector and proceed to the next inspection.

  1. Disconnect the connector from the combination meter assembly.

  1. Check that the connector terminals are not damaged.

    OK:
    The terminals are not deformed or damaged.



NG
REPLACE WIRE HARNESS
OK


3. CHECK WIRE HARNESS (COMBINATION METER ASSEMBLY - BODY GROUND)

  1. E146920E01
    Connect the negative (-) terminal cable to the battery.

  1. Turn the ignition switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    E1-21 (B) - Body ground
    Ignition switch on (IG)
    11 to 14 V
    E1-22 (B2) - Body ground
    Always
    11 to 14 V
    E1-1 (IG+) - Body ground
    Always
    11 to 14 V

  1. Turn the ignition switch off.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E1-20 (ES) - Body ground
    Always
    Below 1 Ω
    E1-40 (E2) - Body ground
    Always
    Below 1 Ω



NG
REPLACE WIRE HARNESS
OK


4. CHECK SRS WARNING LIGHT
  1. Connect the connector to the combination meter assembly.

  1. Disconnect the connector from the center airbag sensor assembly.

  1. Connect the negative (-) terminal cable to the battery.

  1. Turn the ignition switch on (IG).

  1. Check the SRS warning light condition.

    OK:
    After the primary check period, the SRS warning light goes off for approximately 10 seconds and remains on.

    HINT:
    The primary check is performed for approximately 6 seconds after the ignition switch is turned on (IG).



NG
REPLACE COMBINATION METER ASSEMBLY (Click here)
OK

REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)


← SRS Warning Light Remains ON (from Jul 2012)SRS Warning Light does not Come ON (Aug 2008 – Jun 2010) →