B1860/64 Short in Driver Side Knee Airbag Squib Circuit
Diagnostic trouble codes · Vehicles built from Jul 2010
Also covers:
- B1861/64 Open in Driver Side Knee Airbag Squib Circuit
- B1862/64 Short to GND in Driver Side Knee Airbag Squib Circuit
- B1863/64 Short to B+ in Driver Side Knee Airbag Squib Circuit
Versions by build date: May 2007 – Jul 2008 Aug 2008 – Jun 2010 from Jul 2010
DESCRIPTION
The driver side knee airbag squib circuit consists of the center airbag sensor assembly and the driver side knee airbag assembly.This circuit instructs the SRS to deploy when deployment conditions are met.
These DTCs are recorded when a malfunction is detected in the driver side knee airbag squib circuit.
| DTC No. |
DTC Detection Condition |
Trouble Area |
| B1860/64 |
|
|
| B1861/64 |
|
|
| B1862/64 |
|
|
| B1863/64 |
|
|
WIRING DIAGRAM


INSPECTION PROCEDURE
- HINT:
- Perform the simulation method by selecting "check mode" (signal check) with the intelligent tester (Click here).
- After selecting "check mode" (signal check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city or rough road (Click here).
- Perform the simulation method by selecting "check mode" (signal check) with the intelligent tester (Click here).
| 1. CHECK CONNECTORS |
Turn the ignition switch off.

Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Check that the connector are properly connected to the driver side knee airbag assembly and center airbag sensor assembly.
- OK:
- The connectors are properly connected.
- HINT:
- If the connector are not connected securely, reconnect the connectors and proceed to the next inspection.
Disconnect the connectors from the driver side knee airbag assembly and center airbag sensor assembly.
Check that the connector terminals are not damaged.
- OK:
- The terminals are not deformed or damaged.
Check that the instrument panel wire connector (on the driver side knee airbag assembly side) is not damaged.
- OK:
- The lock button is not disengaged, and the claw of the lock is not deformed or damaged.
|
|
||||
| OK | |
| 2. CHECK DRIVER SIDE KNEE AIRBAG ASSEMBLY (DRIVER SIDE KNEE AIRBAG SQUIB) |
Connect SST (resistance 2.1 Ω) to connector C.

- CAUTION:
- Never connect the tester to the driver side knee airbag assembly (driver side knee airbag squib) for measurement, as this may lead to a serious injury due to airbag deployment.
- NOTICE:
- Do not forcibly insert SST into the terminals of the connector when connecting.
- Insert SST straight into the terminals of the connector.
- Do not forcibly insert SST into the terminals of the connector when connecting.
- SST
- 09843-18061
Connect the negative (-) terminal cable to the battery.
Turn the ignition switch on (IG), and wait for at least 60 seconds.
Clear the DTCs stored in the memory (Click here).
Turn the ignition switch off.
Turn the ignition switch on (IG), and wait for at least 60 seconds.
Check for DTCs (Click here).
- OK:
- DTC B1860, B1861, B1862, B1863, or 64 is not output.
- HINT:
- Codes other than DTC B1860, B1861, B1862, B1863, and 64 may be output at this time, but they are not related to this check.
|
|
||||
| OK | ||
| ||
| 3. CHECK INSTRUMENT PANEL WIRE (DRIVER SIDE KNEE AIRBAG SQUIB CIRCUIT) |
Turn the ignition switch off.

Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Disconnect SST from connector C.
Disconnect the connector from the center airbag sensor assembly.
Check for a short to B+ in the circuit.
Connect the negative (-) terminal cable to the battery.
Turn the ignition switch on (IG).
Measure the voltage according to the value(s) in the table below.
- Standard voltage:
Tester Connection
Switch Condition
Specified Condition
D26-1 (DK+) - Body ground
Ignition switch on (IG)
Below 1 V
D26-2 (DK-) - Body ground
Ignition switch on (IG)
Below 1 V
Check for an open in the circuit.
Turn the ignition switch off.
Disconnect the negative (-) terminal cable from the battery, and wait for at least 90 seconds.
Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Switch Condition
Specified Condition
D26-1 (DK+) - D26-2 (DK-)
Always
Below 1 Ω
Check for a short to ground in the circuit.
Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Switch Condition
Specified Condition
D26-1 (DK+) - Body ground
Always
1 MΩ or higher
D26-2 (DK-) - Body ground
Always
1 MΩ or higher
Check for a short in the circuit.
Release the activation prevention mechanism built into connector B (Click here).
Measure the resistance according to the value(s) in the table below.
- Standard resistance:
Tester Connection
Switch Condition
Specified Condition
D26-1 (DK+) - D26-2 (DK-)
Always
1 MΩ or higher
|
|
||||
| OK | |
| 4. CHECK CENTER AIRBAG SENSOR ASSEMBLY |
Restore the released activation prevention mechanism of connector B to the original condition.

Connect the connectors to the driver side knee airbag assembly and the center airbag sensor assembly.
Connect the negative (-) terminal cable to the battery.
Turn the ignition switch on (IG), and wait for at least 60 seconds.
Clear the stored DTCs in the memory (Click here).
Turn the ignition switch off.
Turn the ignition switch on (IG), and wait for at least 60 seconds.
Check for DTCs (Click here).
- OK:
- DTC B1860, B1861, B1862, B1863, or 64 is not output.
- HINT:
- Codes other than DTC B1860, B1861, B1862, B1863, and 64 may be output at this time, but they are not related to this check.
|
|
||||
| OK | ||
| ||
