2007-2013 Highlander Kluger · Service Manual TRANSMISSION

DISASSEMBLY

Removal / installation · Vehicles built from May 2007


1. INSPECT OIL PUMP ASSEMBLY

  1. D009205
    Turn the drive gear with 2 screwdrivers and make sure that it rotates smoothly.

    NOTICE:
    Be careful not to damage the oil seal lip.


2. REMOVE CLUTCH DRUM OIL SEAL RING

  1. D003650E03
    Remove the 2 clutch drum oil seal rings.


3. REMOVE STATOR SHAFT ASSEMBLY

  1. D003651E01
    Using a "TORX" socket (T30), remove the 11 bolts and stator shaft.


4. INSPECT CLEARANCE OF OIL PUMP ASSEMBLY

  1. D009207E03
    Push the driven gear to one side of the body.

  1. Using a feeler gauge, measure the clearance.

    Standard body clearance:
    0.10 to 0.17 mm (0.0039 to 0.0067 in.)

    Maximum body clearance:
    0.17 mm (0.0067 in.)

    If the body clearance is greater than the maximum, replace the oil pump body sub-assembly.

  1. D009208
    Using a feeler gauge, measure the tip clearance between the driven gear teeth and drive gear teeth.

    Standard tip clearance:
    0.07 to 0.15 mm (0.0028 to 0.0059 in.)
    Maximum tip clearance:
    0.15 mm (0.0059 in.)

    If the tip clearance is greater than the maximum, replace the oil pump body sub-assembly.

  1. D009209
    Using a straightedge and feeler gauge, measure the side clearance of both gears.

    Standard side clearance:
    0.02 to 0.05 mm (0.0008 to 0.0020 in.)
    Maximum side clearance:
    0.05 mm (0.0020 in.)

    Drive gear thickness: mm (in.) 
    Mark
    Thickness
    A
    11.690 to 11.699 (0.4602 to 0.4606)
    B
    11.700 to 11.709 (0.4606 to 0.4610)
    C
    11.710 to 11.720 (0.4610 to 0.4614)
    D
    11.721 to 11.730 (0.4615 to 0.4618)
    E
    11.731 to 11.740 (0.4619 to 0.4622)
    Driven gear thickness: mm (in.) 
    Mark
    Thickness
    A
    11.690 to 11.699 (0.4602 to 0.4606)
    B
    11.700 to 11.709 (0.4606 to 0.4610)
    C
    11.710 to 11.720 (0.4610 to 0.4614)
    D
    11.721 to 11.730 (0.4615 to 0.4618)
    E
    11.731 to 11.740 (0.4619 to 0.4622)


5. REMOVE FRONT OIL PUMP DRIVE GEAR

  1. D009206E02
    Remove the front oil pump drive gear.


6. REMOVE FRONT OIL PUMP DRIVEN GEAR

  1. C119012
    Remove the front oil pump driven gear.


7. REMOVE FRONT OIL PUMP BODY O-RING

  1. D025586E03
    Using a screwdriver, remove the O-ring.

    HINT:
    Tape the screwdriver before use.


8. REMOVE FRONT OIL PUMP OIL SEAL

  1. D003647E01
    Mount the oil pump in a soft jaw vise.

  1. Using SST, remove the oil seal from the oil pump body.

    SST
    09308-00010  

← COMPONENTS (from May 2007)INSPECTION (from May 2007) →