2007-2013 Highlander Kluger · Service Manual TRANSMISSION

REASSEMBLY

Removal / installation · Vehicles built from May 2007


1. INSTALL UNDERDRIVE CLUTCH DRUM O-RING

  1. D026465E04
    Coat a new O-ring with ATF and install it to the underdrive clutch drum.

    NOTICE:
    Make sure that the O-ring is not twisted or pinched.


2. INSTALL UNDERDRIVE CLUTCH PISTON SET

  1. D003860
    Coat the underdrive clutch piston with ATF, and install it to the underdrive clutch piston drum.

    NOTICE:
    1. Be careful not to damage the O-ring.
    2. Be careful not to damage the lip of the piston.


3. INSTALL UNDERDRIVE CLUTCH RETURN SPRING SUB-ASSEMBLY

  1. C056360E06
    Install the return spring to the underdrive clutch drum.

    NOTICE:
    After installing the spring sub-assembly, check that all of the springs are engaged in the piston correctly.

  1. Coat the clutch balancer with ATF.

  1. C056359E03
    Install the clutch balancer to the underdrive clutch drum.

    NOTICE:
    Be careful not to damage the lip of the clutch balancer.

  1. D003703E01
    Place SST on the clutch balancer and compress the piston return spring with a press.
    SST
    09350-32014   (09351-32070)

  1. Using a snap ring expander, install the snap ring to the underdrive clutch drum.

  1. Be sure that the end gap of the snap ring is not aligned with the spring retainer claw.

    NOTICE:
    1. Stop the press when the spring seat is lowered to the place 1 to 2 mm (0.039 to 0.078 in.) from the snap ring groove. This prevents the spring seat from being deformed.
    2. Do not expand the snap ring excessively.

  1. D025592E01
    Set the end gap of the snap ring in the underdrive clutch drum as shown in the illustration.

    NOTICE:
    The end gap of the snap ring should not align with any of the stoppers.


4. INSTALL NO. 1 UNDERDRIVE CLUTCH DISC

  1. D026431E01
    Coat the 4 discs with ATF.

  1. Install the 4 plates, 4 discs, and flange to the underdrive clutch drum.

    NOTICE:
    Make sure that the plates, discs, and flange are installed as shown in the illustration.


5. INSTALL NO. 2 UNDERDRIVE CLUTCH FLANGE HOLE SNAP RING

  1. D003701
    Using a screwdriver, install the No. 2 underdrive clutch flange hole snap ring.

  1. Check that the end gap of the snap ring is not aligned with one of the cutouts.

    NOTICE:
    The snap ring should be fully engaged in the groove of the drum.


6. INSPECT UNDERDRIVE PACK CLEARANCE

  1. D026429E01
    Install the underdrive clutch to the transaxle case.

    NOTICE:
    Be careful not to damage the oil seal rings.

  1. Install a dial indicator as shown in the illustration.

  1. Measure the underdrive clutch pack clearance while applying and releasing compressed air (392 kPa, 4.0 kgf/cm2, 57 psi).

    Pack clearance:
    1.51 to 1.71 mm (0.0594 to 0.0673 in.)

    If the pack clearance is not as specified, inspect the discs, plates, and flange.

    HINT:
    There are 5 different thicknesses of flanges available.
    Flange thickness: mm (in.) 
    Mark
    Thickness
    Mark
    Thickness
    1
    3.0 (0.118)
    4
    3.6 (0.141)
    2
    3.2 (0.126)
    5
    3.8 (0.150)
    3
    3.4 (0.134)
    -
    -

← INSPECTION (from May 2007)COMPONENTS (from May 2007) →