2007-2013 Highlander Kluger · Service Manual TRANSMISSION

REASSEMBLY

Removal / installation · Vehicles built from May 2007


1. INSTALL UNDERDRIVE PLANETARY RING GEAR

  1. D008112E01
    Install a new snap ring to the outer race of a new radial ball bearing rear.

    HINT:
    When replacing the bearing, replace the counter driven gear with a new one.

  1. D008113
    Using a piston ring compressor, squeeze the snap ring.

  1. D008114E01
    Using SST and a press, press in the outer race of the radial ball bearing rear.
    SST
    09950-60020   (09951-00890)
    09950-70010   (09951-07100)

    NOTICE:
    Be sure not to damage the snap ring while installing the outer race.

  1. D003827E08
    Install the underdrive planetary ring gear to the counter driven gear.

  1. D008115E01
    Using snap ring pliers, install the snap ring.


2. INSTALL UNDERDRIVE PLANETARY GEAR ASSEMBLY

  1. D026435E01
    Using SST and a press, press the radial ball bearing rear in the underdrive planetary gear.
    SST
    09502-12010  
    09950-60010   (09951-00260)
    09950-70010   (09951-07100)

    NOTICE:
    Press the bearing until it becomes flat at the bottom.

  1. D008117
    Install the counter driven gear with planetary ring gear to the underdrive planetary gear.

  1. D026436E01
    Using SST and a press, press in a new radial ball bearing front.
    SST
    09502-12010  
    09950-60010   (09951-00260)
    09950-70010   (09951-07100)

    NOTICE:
    Press the counter driven gear while rotating it.

  1. D026433E01
    Using SST and a press, press in the parking lock gear.
    SST
    09502-12010  
    09950-60010   (09951-00260)
    09950-70010   (09951-07100)

    NOTICE:
    Press the counter driven gear while rotating it.


3. INSTALL DIFFERENTIAL DRIVE PINION

  1. D026434E01
    Using SST and a press, press the differential drive pinion.
    SST
    09726-40010  
    09950-60010   (09951-00260)
    09950-70010   (09951-07100)

    NOTICE:
    1. Press the counter driven gear while rotating it.
    2. Check the number and position of the gear teeth.

    NOTICE:
    Press the counter driven gear while rotating it.


4. INSTALL CYLINDRICAL ROLLER BEARING RACE INNER

  1. D026432E01
    Using SST and a press, press the cylindrical roller bearing race inner.
    SST
    09506-35010  
    09950-60010   (09951-00260)
    09950-70010   (09951-07100)

    NOTICE:
    Press the counter driven gear while rotating it.


5. INSTALL FRONT PLANETARY GEAR NUT

  1. D025609E06
    Place the underdrive planetary gear in a soft jaw vise.

    NOTICE:
    Be careful not to damage the differential drive pinion.

  1. Using a socket wrench, install a new lock nut.

    Torque:
    280 N*m{ 2855 kgf*cm , 207 ft.*lbf }

    HINT:
    Use a torque wrench with a fulcrum length of 750 mm (29.53 in.).

  1. C056809
    Using a pin punch and hammer, stake the lock nut.

    CAUTION:
    Be sure that there are no cracks on the nut.


6. INSPECT UNDERDRIVE PLANETARY GEAR PRELOAD

  1. D025593E01
    Using SST, secure the underdrive planetary gear assembly.
    SST
    09387-00050  

  1. D025594E01
    Using SST and a torque wrench, measure the turning torque of the underdrive planetary gear assembly while rotating the torque wrench at 60 rpm.
    SST
    09387-00050  

    Turning torque at 60 rpm.:
    0.50 to 1.42 N*m (5.1 to 14.5 kgf*cm, 4.4 to 12.6 in.*lbf)

    HINT:
    Use a torque wrench with a fulcrum length of 160 mm (6.3 in.).

← INSPECTION (from May 2007)COMPONENTS (from May 2007) →