2007-2013 Highlander Kluger · Service Manual SUSPENSION & AXLE

REMOVAL

Removal / installation · Vehicles built from May 2007


1. REMOVE FRONT WHEEL

2. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY LH

  1. E150144
    Remove the nut, and the front wiper arm and blade assembly LH.


3. REMOVE FRONT WIPER ARM AND BLADE ASSEMBLY RH

  1. E150145
    Remove the nut, and the front wiper arm and blade assembly RH.


4. LOOSEN FRONT SUPPORT TO FRONT SHOCK ABSORBER NUT

  1. C165911
    Loosen the front support to front shock absorber nut of the front shock absorber.

    NOTICE:
    1. Do not remove the front support to front shock absorber nut.
    2. Loosen the nut only when the front shock absorber with coil spring needs to be disassembled.


5. REMOVE COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY

  1. E150146
    Disengage the 2 claws and disconnect the front fender to cowl side seal LH.

  1. E150147
    Disengage the 2 claws and disconnect the front fender to cowl side seal RH.

  1. Remove the 2 clips.

    E150149

  1. Disengage the 20 claws and remove the cowl top ventilator louver sub-assembly.


6. REMOVE WINDSHIELD WIPER MOTOR AND LINK

  1. E150150
    Disconnect the connector.

  1. Remove the 4 bolts, and the windshield wiper motor and link assembly.


7. REMOVE OUTER COWL TOP PANEL SUB-ASSEMBLY

  1. C165925
    Disengage the 4 clamps and separate the wiper wire harness from the outer cowl top panel sub-assembly.

  1. C165926
    Remove the 8 bolts, 6 nuts, and the outer cowl top panel sub-assembly.


8. SEPARATE FRONT SPEED SENSOR

  1. C167708
    Remove the bolt and clamp, and separate the front speed sensor and front flexible hose.


9. SEPARATE FRONT STABILIZER LINK ASSEMBLY

  1. C165915
    Remove the nut and separate the front stabilizer link assembly from the front shock absorber.

    HINT:
    If the ball joint turns together with the nut, use a hexagon wrench (6 mm) to hold the stud.


10. REMOVE FRONT SHOCK ABSORBER WITH COIL SPRING

  1. C165927E01
    Support the front axle using a jack and wooden block.

  1. C165908
    Remove the 2 bolts and 2 nuts, and separate the front shock absorber with coil spring (lower side) from the steering knuckle.

    NOTICE:
    When removing the nuts, keep the bolts from rotating.

  1. C165912
    Remove the nut and 2 spacers on the upper side of the front shock absorber with coil spring.

    NOTICE:
    Make sure that the front speed sensor is completely separated from the front shock absorber with coil spring.


11. REMOVE FRONT SUPPORT TO FRONT SHOCK ABSORBER NUT

  1. C267414E01
    Secure SST in a vise.
    SST
    09727-30021   (09727-00010, 09727-00031)
    09727-00050  

  1. C263591
    Attach the arm of SST to the diameter of the front coil spring.

    CAUTION:
    1. Make sure that the front coil spring is installed so that the distance between the upper and lower hooks of SST is at the maximum.
    2. Make sure that the claws of the hooks are securely attached.

  1. Using SST, compress the front coil spring.

    CAUTION:
    1. If the front coil spring bends during the compression, immediately stop the compression and reinstall SST.
    2. Do not compress the spring until the coil springs contact each other.
    3. Do not use an impact wrench. It will damage SST.

  1. C267415
    Confirm that the front coil spring becomes free and remove the front support to front shock absorber nut.

    CAUTION:
    Do not remove the front support to front shock absorber nut when the front coil spring is not free.


12. REMOVE FRONT SUSPENSION SUPPORT SUB-ASSEMBLY

13. REMOVE FRONT SUSPENSION SUPPORT BEARING

14. REMOVE FRONT COIL SPRING UPPER SEAT

15. REMOVE FRONT COIL SPRING UPPER INSULATOR

16. REMOVE FRONT COIL SPRING

17. REMOVE FRONT SPRING BUMPER

18. REMOVE FRONT COIL SPRING LOWER INSULATOR
← COMPONENTS (from Jul 2010)INSPECTION (from May 2007) →